Η ΒΥΠ διαθέτει αντίτυπο της διατριβής σε έντυπη μορφή στο βιβλιοστάσιο διδακτορικών διατριβών που βρίσκεται στο ισόγειο του κτιρίου της. / Τα ψηφιακά συστήματα UWB (Ultra Wide-Band) παρέχουν τη δυνατότητα ασύρματης μετάδοσης σε πολύ υψηλό ρυθμό. Λόγω του μεγάλου εύρους ζώνης, το κανάλι εισάγει πολλαπλές ανακλάσεις οι οποίες φέρουν μεγάλο ποσοστό της ωφέλιμης ενέργειας του μεταδιδόμενου σήματος. Η ικανότητα του δέκτη για σύλληψη όσο το δυνατόν περισσότερης ωφέλιμης ενέργειας έχει αντίκτυπο στη συνολική απόδοση του συστήματος. Η χρήση της τεχνικής διαμόρφωσης με πολύπλεξη συχνότητας ορθογωνίων φερουσών (OFDM), που στην συγκεκριμένη περίπτωση (UWB) συνδυάζεται με πολυζωνική (Multi-band) μετάδοση, απλοποιεί τη διαχείριση του συνολικού φάσματος συχνοτήτων. Όμως η διαμόρφωση OFDM παρουσιάζει ιδιαίτερη ευαισθησία σε προβλήματα τόσο διασυμβολικής παρεμβολής (ISI) όσο και διακαναλικής παρεμβολής (ICI), λόγω του έντονου διασκορπιστικού χαρακτήρα του καναλιού καθώς επίσης και τυχόν αποκλίσεων που εμφανίζονται στους ταλαντωτές πομπού-δέκτη. Τα παραπάνω επιβάλλουν τη χρήση σύνθετων αλγορίθμων συγχρονισμού και συντονισμού (time and frequency synchronization) μεταξύ πομπού και δέκτη για την ομαλή λειτουργία. Στα πλαίσια της διπλωματικής αυτής θα πραγματοποιηθεί επιλογή κατάλληλων αλγορίθμων για τα προαναφερθέντα προβλήματα, οι οποίοι θα πρέπει να πληρούν τις προδιαγραφές του υπό διαμόρφωση διεθνούς προτύπου 802.15.3α και θα αναπτυχθούν βέλτιστες αρχιτεκτονικές VLSI, με στόχο τόσο το χαμηλό κόστος υλοποίησης όσο και την χαμηλή κατανάλωση ισχύος. / In this project have been studied the low power VLSI architecture for synchronization algorithms in Multi-band UWB Wireless systems. The main issues are timing and frequency synchronization algorithms.

In this research we attempted several modifications to microstrip ring/loop antennas to design multi-frequency antennas through systematic approaches. Such multi-frequency antennas can be useful while building compact terminals to operate at multiple wireless standards. One of the primary contributions was the use of a capacitive feed arrangement that enables simultaneous excitation of multiple concentric rings from an underlying transmission line. The combined antenna operates in the same resonant bands as the individual rings and avoids some of the bands at harmonic frequencies. A similar feeding arrangement is used to obtain dual band characteristics from just one ring, with improved bandwidth. This is made possible by widening two adjacent sides of a square ring antenna symmetrically, and attaching an open stub to the inner edge of the side opposite to the feed line. Use of fractal segments replacing the side with the stub also results in a similar performance. Use of fractal geometries has been widely associated with multi-functional antennas. It has been observed from the parametric studies that, the ratio of the resonant frequencies can range from 1.5 to 2.0. This shows some flexibility in systematically designing dual-band antennas with a desired pair of resonant frequencies. An analysis technique based on multi-port network modeling (MNM) has been proposed to accurately predict the input characteristics of these antennas. This approach can make use of the ordered nature of fractal geometries to simplify computations. Several prototype antennas have been fabricated and tested successfully to validate simulation and analytical results.

This thesis analyzes charge properties of (undoped) cuprate compounds from a theoretical point of view. The central question considered here is: How does the dimensionality of the CU-O sub-structure influence its charge degrees of freedom? The model used to describe the Cu-O sub-structure is the three- (or multi-) band Hubbard model. Analytical approaches are employed (ground-state formalism for strongly correlated systems, Mori-Zwanzig projection technique) as well as numerical simulations (Projector Quantum Monte Carlo, exact diagonalization). Several results are compared to experimental data. The following materials have been chosen as candidates to represent different Cu-O sub-structures: Bi2CuO4 (isolated CuO4 plaquettes), Li2CuO2 (chains of edge-sharing plaquettes), Sr2CuO3 (chains of corner-sharing plaquettes), and Sr2CuO2Cl2 (planes of plaquettes). Several results presented in this thesis are valid for other cuprates as well. Two different aspects of charge properties are analyzed: 1) Charge properties of the ground state 2) Charge excitations. (gekürzte Fassung)

This thesis deals with modeling and produce of reconfigurable multi-band planar antennas, which allow electrical shifting of frequency band. After antennas simulation with PIN diode and FET switch in a commercial program CST MW, another step is to optimize the antenna for a new substrate. The next step was to produce antennas. Finally, the optimized antennas are compared with the measurement on experimental antennas.

Multiple-Input-Multiple-Output (MIMO) antenna technology refers to an antenna with multiple radiators at both transmitter and receiver ends. It is designed to increase the data rate in wireless communication systems by achieving multiple channels occupying the same bandwidth in a multipath environment. The main drawback associated with this technology is the coupling between the radiating elements. A MIMO antenna system merely acts as an antenna array if the coupling between the radiating elements is high. For this reason, strong decoupling between the radiating elements should be achieved, in order to utilize the benefits of MIMO technology. The main objectives of this thesis are to investigate and implement several printed MIMO antenna geometries with integrated decoupling approaches for WLAN, WiMAX, and 5G applications. The characteristics of MIMO antenna performance have been reported in terms of scattering parameters, envelope correlation coefficient (ECC), total active reflection coefficient (TARC), channel capacity loss (CCL), diversity gain (DG), antenna efficiency, antenna peak gain and antenna radiation patterns. Three new 2×2 MIMO array antennas are proposed, covering dual and multiple spectrum bandwidths for WLAN (2.4/5.2/5.8 GHz) and WiMAX (3.5 GHz) applications. These designs employ a combination of DGS and neutralization line methods to reduce the coupling caused by the surface current in the ground plane and between the radiating antenna elements. The minimum achieved isolation between the MIMO antennas is found to be better than 15 dB and in some bands exceeds 30 dB. The matching impedance is improved and the correlation coefficient values achieved for all three antennas are very low. In addition, the diversity gains over all spectrum bands are very close to the ideal value (DG = 10 dB). The forth proposed MIMO antenna is a compact dual-band MIMO antenna operating at WLAN bands (2.4/5.2/5.8 GHz). The antenna structure consists of two concentric double square rings radiating elements printed symmetrically. A new method is applied which combines the defected ground structure (DGS) decoupling method with five parasitic elements to reduce the coupling between the radiating antennas in the two required bands. A metamaterial-based isolation enhancement structure is investigated in the fifth proposed MIMO antenna design. This MIMO antenna consists of two dual-band arc-shaped radiating elements working in WLAN and Sub-6 GHz 5th generation (5G) bands. The antenna placement and orientation decoupling method is applied to improve the isolation in the second band while four split-ring resonators (SRRs) are added between the radiating elements to enhance the isolation in the first band. All the designs presented in this thesis have been fabricated and measured, with the simulated and measured results agreeing well in most cases. / Higher Committee for Education Development in Iraq (HCED)

Characteristic modes (CMs) provide deep insight into the electromagnetic behaviour of any arbitrarily shaped conducting structure because the CMs are unique to the geometry of the object. We exploit this very fact by predicting a perhaps surprising number of important antenna metrics such as resonance frequency, radiation efficiency and antenna Q (bandwidth) without needing to specify a feeding location. In doing so, it is possible to define a collection of objective functions that can be used in an optimizer to shape-synthesize antennas without needing to define a feed location a priori. We denote this novel form of optimization “feedless” or “excitation-free” antenna shape synthesis. Fundamentally, we are allowing the electromagnetics to dictate how the antenna synthesis should proceed and are in no way imposing the physical constraints enforced by fixed feeding structures. This optimization technique is broadly applied to three major areas of antenna research: electrically small antennas, multi-band antennas and reflectarrays. Thus, the scope of applicability ranges from small antennas, to intermediate sizes and concludes with electrically large antenna designs, which is a testament to the broad applicability of characteristic mode theory. Another advantage of feedless electromagnetic shape synthesis is the ability to synthesize antennas whose desirable properties approach the fundamental limits imposed by electromagnetics. As an additional benefit, the feedless optimization technique is shown to have greater computational efficiency than traditional antenna optimization techniques.

Characteristic modes (CMs) provide deep insight into the electromagnetic behaviour of any arbitrarily shaped conducting structure because the CMs are unique to the geometry of the object. We exploit this very fact by predicting a perhaps surprising number of important antenna metrics such as resonance frequency, radiation efficiency and antenna Q (bandwidth) without needing to specify a feeding location. In doing so, it is possible to define a collection of objective functions that can be used in an optimizer to shape-synthesize antennas without needing to define a feed location a priori. We denote this novel form of optimization “feedless” or “excitation-free” antenna shape synthesis. Fundamentally, we are allowing the electromagnetics to dictate how the antenna synthesis should proceed and are in no way imposing the physical constraints enforced by fixed feeding structures. This optimization technique is broadly applied to three major areas of antenna research: electrically small antennas, multi-band antennas and reflectarrays. Thus, the scope of applicability ranges from small antennas, to intermediate sizes and concludes with electrically large antenna designs, which is a testament to the broad applicability of characteristic mode theory. Another advantage of feedless electromagnetic shape synthesis is the ability to synthesize antennas whose desirable properties approach the fundamental limits imposed by electromagnetics. As an additional benefit, the feedless optimization technique is shown to have greater computational efficiency than traditional antenna optimization techniques.

The radio frequency (RF) spectrum as a natural resource is severely under-utilized over time and space due to an inefficient licensing framework. As a result, in-creasing cellular and wireless network usage is placing significant demands on the licensed spectrum. This has led to the development of cognitive radios, software defined radios and mm-wave radios. Cognitive radios (CRs) enable more efficient spectrum usage over a wide range of frequencies and hence have emerged as an effective solution to handle huge network demands. They promise versatility, flex-ability and cognition which can revolutionize communications systems. However, they present greater challenges to the design of radio frequency (RF) front-ends. Instead of a narrow-band front-end optimized and tuned to the carrier frequency of interest, cognitive radios demand front-ends which are versatile, configurable, tun-able and capable of transmitting and receiving signals with different bandwidths and modulation schemes. The primary purpose of this thesis is to design a re-configurable, wide-band and low phase-noise fast settling frequency synthesizer for cognitive radio applications. Along with frequency generation, an area efficient multi-band low noise amplifier (LNA) with integrated built-in-self-test (BIST) and a strong immunity to interferers has also been proposed and implemented for these radios. This designed LNA relaxes the specification of harmonic content in the synthesizer output. Finally some preliminary work has also been done for mm-wave (V-band) frequency synthesis. The Key Contributions of this thesis are: A frequency synthesizer, based on a type-2, third-order Phase Locked Loop (PLL), covering a frequency range of 0.1-5.4 GHz, is implemented using a 0.13 µm CMOS technology. The PLL uses three voltage controlled oscillators (VCOs) to cover the whole range. It is capable of switching between any two frequencies in less than 3 µs and has phase noise values, compatible with most communication standards. The settling of the PLL in the desired state is achieved in dynamic multiple steps rather than traditional single step settling. This along with other circuit techniques like a DAC-based discriminator aided charge pump, fast acquisition pulse-clocked based PFD and timing synchro-negation is used to obtain a significantly reduced settling time A single voltage controlled LC-oscillator (LC-VCO) has been designed to cover a wide range of frequencies (2.0-4.1 GHz) using an area efficient and switch-able multi-tap inductor and a capacitor bank. The switching of the multi-tap inductor is done in the most optimal manner so as to get good phase-noise at the output. The multi-tap inductor provides a significant area advantage, and in spite of a degraded Q, provides an acceptable phase noise of -123 dBc/Hz and -113 dBc/Hz at an offset of 1 MHz at carrier frequencies of 2 and 4 GHz, respectively. Implemented in a 0.13 µm CMOS technology, the oscillator with ≈ 69 % tuning range, occupies an active area of only 0.095 mm2. An active inductor based noise-filter has been proposed to improve the phase-noise performance of the oscillator without much increase in the area. A variable gain multi-band low noise amplifier (LNA) is designed to operate over a wide range of frequencies (0.8 GHz to 2.4 GHz) using an area efficient switchable-π network. The LNA can be tuned to different gain and linearity combinations for different band settings. Depending upon the location of the interferers, a specific band can be selected to provide optimum gain and the best signal-to-intermodulation ratio. This is accomplished by the use of an on-chip Built-in-Self-Test (BIST) circuit. The maximum power gain of the amplifier is 19 dB with a return loss better than 10 dB for 7 mW of power consumption. The noise figure is 3.2 dB at 1 GHz and its third-order intercept point (I I P3) ranges from -15 dBm to 0 dBm. Implemented in a 0.13 µm CMOS technology, the LNA occupies an active area of about 0.29 mm2. Three different types of VCOs (stand-alone LC VCO, push-push VCO and a ring oscillator based VCO) for generating mm-wave frequencies have been implemented using 65-nm CMOS technology and their measured results have been analyzed

Characteristic modes (CMs) provide deep insight into the electromagnetic behaviour of any arbitrarily shaped conducting structure because the CMs are unique to the geometry of the object. We exploit this very fact by predicting a perhaps surprising number of important antenna metrics such as resonance frequency, radiation efficiency and antenna Q (bandwidth) without needing to specify a feeding location. In doing so, it is possible to define a collection of objective functions that can be used in an optimizer to shape-synthesize antennas without needing to define a feed location a priori. We denote this novel form of optimization “feedless” or “excitation-free” antenna shape synthesis. Fundamentally, we are allowing the electromagnetics to dictate how the antenna synthesis should proceed and are in no way imposing the physical constraints enforced by fixed feeding structures. This optimization technique is broadly applied to three major areas of antenna research: electrically small antennas, multi-band antennas and reflectarrays. Thus, the scope of applicability ranges from small antennas, to intermediate sizes and concludes with electrically large antenna designs, which is a testament to the broad applicability of characteristic mode theory. Another advantage of feedless electromagnetic shape synthesis is the ability to synthesize antennas whose desirable properties approach the fundamental limits imposed by electromagnetics. As an additional benefit, the feedless optimization technique is shown to have greater computational efficiency than traditional antenna optimization techniques.

Η πληθώρα των εφαρμογών που μπορεί να εξυπηρετήσει η τεχνολογία Υπερευρείας Ζώνης (UWB), από τα ασύρματα προσωπικά δίκτυα υψηλών ταχυτήτων, μέχρι τα ασύρματα δίκτυα αισθητήρων με δυνατότητες ακριβούς εντοπισμού θέσης, και τα ασύρματα δίκτυα ιατρικών αισθητήρων, έχει προκαλέσει έντονο ερευνητικό ενδιαφέρον γύρω από τις υλοποιήσεις UWB συστημάτων. Η ασυνήθιστα μεγάλη περιοχή συχνοτήτων που έχει ανατεθεί στο UWB, από τα 3.1-10.6 GHz, επιτρέπει την επίτευξη υψηλών ταχυτήτων με απλά σχήματα διαμόρφωσης, ωστόσο, λόγω της διαμοίρασης του φάσματος με τις υφιστάμενες τεχνολογίες ασύρματης δικτύωσης, οι UWB εκπομπές πρέπει να περιορίζονται σε ισχύ κάτω από το κατώφλι των -41.3 dBm/MHz, ικανοποιώντας πολύ αυστηρές μάσκες εκπομπής που εισάγουν έντονες προκλήσεις στη σχεδίαση των πομπών. Η υλοποίηση αναδιατάξιμων UWB πομπών σε σύγχρονες CMOS τεχνολογίες, με υψηλή φασματική ευελιξία, ταχύτητα και ποιότητα διαμόρφωσης, καθώς και με χαμηλή κατανάλωση, αποτέλεσε το αντικείμενο της συγκεκριμένης διατριβής. Υιοθετώντας την αρχιτεκτονική Multi-Band Impulse-Radio (MB-IR) σε συνδυασμό με την τεχνική Direct Sequence BPSK, η έρευνα προσανατολίστηκε προς την ανάπτυξη καινοτόμων μονάδων βασικής ζώνης, με στόχο την ενεργειακά αποδοτική αντιστροφή Γκαουσιανών μορφοποιημένων παλμών υψηλής ποιότητας φάσματος και διάρκειας μικρότερης ακόμα και από 1 nsec. Προς αυτή την κατεύθυνση, αναπτύχθηκε μια καινοτόμα γεννήτρια Γκαουσιανών παλμών με πολύ χαμηλούς πλευρικούς λοβούς στο φάσμα, τυπικά κάτω από -40 dB, ώστε να υποστηρίζονται οι αυστηρότερες μάσκες εκπομπής ή και μελλοντικές. Η σχεδίασης της προτεινόμενης γεννήτριας είχε ως κριτήριο την ευέλικτη ρύθμιση της διάρκειας των παραγόμενων παλμών, και αξιοποίησε τη χαρακτηριστική μεταφοράς τάσης ενός ωμικά φορτωμένου, ασύμμετρου CMOS αντιστροφέα. Η γεννήτρια βασίζεται κυρίως σε ψηφιακά κυκλώματα πολύ χαμηλής τάσης και, σε σύγκριση με τις υφιστάμενες υλοποιήσεις, παρουσιάζει σημαντικό προβάδισμα στον τομέα της ταχύτητας, καθώς και στο πλάτος εξόδου, η μεγάλη τιμή του οποίου χαλαρώνει σημαντικά τη σχεδίαση του RF front end. Η γεννήτρια μελετήθηκε διεξοδικά, διεξήχθη ανάλυση κλιμάκωσης, έγινε εξαγωγή σχεδιαστικών εξισώσεων και αναπτύχθηκαν εργαλεία λογισμικού για την αυτοματοποιημένη σχεδίασή της. Για περαιτέρω αύξηση της ταχύτητας των παλμικών σημάτων εφαρμόσθηκε ειδική σχεδίαση, η οποία αντιπραγματεύεται την ταχύτητα με το επίπεδο των λοβών του φάσματος. Για την αποδοτική BSPK διαμόρφωση των Γκαουσιανών παλμών αναπτύχθηκε ειδική τοπολογία “Μεταγωγής Σήματος Πυροδότησης Πλήρους Ισορροπίας με Up-Conversion”. Η τοπολογία αυτή, σε αντίθεση με τις ανταγωνιστικές τοπολογίες, αποφεύγει την αντιστροφή του παλμού με αναλογικά κυκλώματα υψηλής κατανάλωσης, αλλά και την αναλογική μεταγωγή, καθώς η διαμόρφωση λαμβάνει χώρα πριν από την παραγωγή των παλμών. Παράλληλα, επιτυγχάνονται υψηλοί ρυθμοί, καθώς και υψηλή ποιότητα διαμόρφωσης λόγω των ισορροπημένων μονοπατιών της τοπολογίας. Η γεννήτρια μαζί με το διαμορφωτή αποτελούν τις καινοτόμες παρεμβάσεις στη μονάδα Βασικής Ζώνης του προτεινόμενου πομπού. Για την ολοκλήρωση της λειτουργικότητας του πομπού, αναπτύχθηκε ένα RF front end, το οποίο αποτελείται από έναν διπλά ισορροπημένο μίκτη, έναν LO buffer, ένα μετατροπέα διαφορικού σήματος σε απλό, και έναν ενισχυτή ισχύος, ο οποίος είναι προσαρμοσμένος στα 50 Ohms, χωρίς να απαιτεί κανένα εξωτερικό στοιχείο. Το RF front end ολοκληρώθηκε μαζί με τη μονάδα βασικής ζώνης, και ο ολοκληρωμένος πομπός κατασκευάστηκε σε τεχνολογία CMOS 130 nm. Το ολοκληρωμένο προσαρτήθηκε στην RF πλακέτα συστήματος με την τεχνική Chip on Board. Για την επιτυχία του συστήματος με την πρώτη προσπάθεια έγινε συσχεδίαση σε επίπεδο IC-Package-PCB, δίνοντας ιδιαίτερη έμφαση στα ζητήματα Signal/Power Integrity. Ο πομπός παρουσίασε την υψηλότερη ταχύτητα από τις ανταγωνιστικές MB-IR UWB υλοποιήσεις, ίση με 1.5 Gbps, με αντίστοιχη ενεργειακή αποδοτικότητα 21 pJoule/bit και μέτρο διανυσματικού σφάλματος 5.5%. Ο πομπός βελτίωσε τους πλευρικούς λοβούς στο φάσμα περισσότερο από 10 dB, ενώ η διατριβή, εκμεταλλευόμενη την αναδιαταξιμότητα του πομπού, παρουσιάζει, επιπλέον, τις πρώτες μετρήσεις σε ταχύτητες εκατοντάδων Mbps για ικανοποίηση της χαμηλής ζώνης της πρόσφατα θεσμοθετημένης, και εξαιρετικά αυστηρής, ευρωπαϊκής μάσκας εκπομπής. / The multitude of applications that Ultra-Wideband (UWB) technology can serve, from high-speed Wireless Personal Area Networks, to Wireless Sensor Networks with precision Geolocation abilities, and Wireless Medical Networks, has attracted intense research interest in the implementation of UWB systems. The unusually wide range of frequencies assigned to UWB, from 3.1-10.6 GHz, allows UWB systems employing low order modulation schemes to enjoy high throughput at low power consumption. However, since UWB shares the spectrum with existing wireless networking technologies, UWB emissions must be limited to a power spectral density below the threshold of -41.3 dBm/MHz, satisfying very stringent emission masks and introducing great challenges in the design of UWB transmitters. The subject of this thesis is the design of low power, fully integrated, reconfigurable CMOS UWB transmitters, with high spectral flexibility, high speed and high modulation quality. Adopting the Multi-Band Impulse-Radio architecture, in conjunction with the Direct Sequence BPSK modulation, the research focused on the development of a baseband unit, able to precisely invert Gaussian shaped, subnanosecond pulses. The key contributions of this thesis are a CMOS Gaussian Pulse Generator and a BSPK modulation topology, which jointly constitute the proposed baseband unit. The Pulse Generator (PG) is based on non-linear shaping, so as to facilitate the configurability of the output pulse duration, and exploits the voltage transfer characteristic of a Resistive Loaded Asymmetrical CMOS Inverter, which results in spectral sidelobes typically better than -40 dB. The PG incorporates mostly-digital low voltage circuits, while the MOSFET devices that undertake the pulse shaping avoid exclusive operation in weak inversion, in contrast to previous implementations. Consequently, the proposed CMOS PG is able to support higher throughput, as well as higher output amplitude, which relaxes considerably the design of the RF front end. This thesis presents a systematic design procedure and a scaling analysis of the non-linear pulse shaper. Moreover, in order to further increase the speed, a special PRF boost technique is proposed, which trades off speed and spectral efficiency for the spectral sidelobes level. Regarding the BPSK modulator, this work introduces the “Trigger Switching Fully Balanced Up-Conversion” topology, which avoids the use of power-hungry and distortion-prone analog circuits for the accurate inversion of the subnanosecond shaped pulses, as well as avoids the application of analog waveform switching to the baseband pulses, since the baseband modulation takes place before the generation of the pulses. The digital nature of the switching lends itself to high data rates, while the balanced paths of the topology ensure high modulation quality with minimal design effort. Wafer probing measurements confirmed the high performance of the baseband unit. The functionality of the transmitter was completed by the development of an RF front end which consists of a double balanced mixer, an LO buffer, a differential to single-ended (DtoSE) converter, and a power amplifier which is ready to drive a 50 Ohms load without requiring any off-chip components. The integrated transmitter, which incorporates the proposed baseband unit and the RF front end, was fabricated in 130 nm CMOS technology. The transmitter RFIC was directly attached to the system RF PCB using the Chip-on-Board packaging option. The First-Pass success of the system was ensured by paying particular attention to Signal/Power Integrity issues and following an IC-Package-PCB co-design procedure. The transmitter was measured up to 1.5 Gbps, which, to the author’s knowledge, was the highest speed amongst the competitive Multi-Band Impulse-Radio UWB implementations in the literature. The corresponding energy efficiency was 21 pJoule/bit and the Error Vector Magnitude (EVM) 5.5%, while the proposed transmitter improved the spectral sidelobes by over 10 dB. Exploiting the reconfigurability of the transmitter, this thesis presents the first measurements at multi-Mbps speeds that completely meet the final version of the European spectrum emission mask.