In wireless communication systems, the use of multiple antennas, also known as Multiple-Input Multiple-Output(MIMO) communications, is now a widely accepted and important technology for improving their reliability and throughput performance. However, in order to achieve the performance gains predicted by the theory, the transmitter and receiver need to have accurate and up-to-date Channel State Information(CSI) to overcome the vagaries of the fading environment. Traditionally, the CSI is obtained at the receiver by sending a known training sequence in the forward-link direction. This CSI has to be conveyed to the transmitter via a low-rate, low latency and noisy feedback channel in the reverse-link direction. This thesis addresses three key challenges in sending the CSI to the transmitter of a MIMO communication system over the reverse-link channel, and provides novel solutions to them. The first issue is that the available CSI at the receiver has to be quantized to a finite number of bits, sent over a noisy feedback channel, reconstructed at the transmitter, and used by the transmitter for precoding its data symbols. In particular, the CSI quantization technique has to be resilient to errors introduced by the noisy reverse-link channel, and it is of interest to design computationally simple, linear filters to mitigate these errors. The second issue addressed is the design of low latency and low decoding complexity error correction codes to provide protection against fading conditions and noise in the reverse-link channel. The third issue is to improve the resilience of the reverse-link channel to fading. The solution to the first problem is obtained by proposing two classes of receive filtering techniques, where the output of the source decoder is passed through a filter designed to reduce the overall distortion including the effect of the channel noise. This work combines the high resolution quantization theory and the optimal Minimum Mean Square Error(MMSE) filtering formulation to analyze, and optimize, the total end-to-end distortion. As a result, analytical expressions for the linear receive filters are obtained that minimize the total end-to-end distortion, given the quantization scheme and source(channel state) distribution. The solution to the second problem is obtained by proposing a new family of error correction codes, termed trellis coded block codes, where a trellis code and block code are concatenated in order to provide good coding gain as well as low latency and low complexity decoding. This code construction is made possible due to the existence of a uniform partitioning of linear block codes. The solution to the third problem is obtained by proposing three novel transmit precoding methods that are applicable to time-division-duplex systems, where the channel reciprocity can be exploited in designing the precoding scheme. The proposed precoding methods convert the Rayleigh fading MIMO channel into parallel Additive White Gaussian Noise(AWGN) channels with fixed gain, while satisfying an average transmit power constraint. Moreover, the receiver does not need to have knowledge of the CSI in order to decode the received data. These precoding methods are also extended to Rayleigh fading multi-user MIMO channels. Finally, all the above methods are applied to the problem of designing a low-rate, low-latency code for the noisy and fading reverse-link channel that is used for sending the CSI. Simulation results are provided to demonstrate the improvement in the forward-link data rate due to the proposed methods. Note that, although the three solutions are presented in the context of CSI feedback in MIMO communications, their development is fairly general in nature, and, consequently, the solutions are potentially applicable in other communication systems also.

L’estimation fonctionnelle basée sur les espaces de Hilbert à noyau reproduisant demeure un sujet de recherche actif pour l’identification des systèmes non linéaires. L'ordre du modèle croit avec le nombre de couples entrée-sortie, ce qui rend cette méthode inadéquate pour une identification en ligne. Le critère de cohérence est une méthode de parcimonie pour contrôler l’ordre du modèle. Le modèle est donc défini à partir d'un dictionnaire de faible taille qui est formé par les fonctions noyau les plus pertinentes.Une fonction noyau introduite dans le dictionnaire y demeure même si la non-stationnarité du système rend sa contribution faible dans l'estimation de la sortie courante. Il apparaît alors opportun d'adapter les éléments du dictionnaire pour réduire l'erreur quadratique instantanée et/ou mieux contrôler l'ordre du modèle.La première partie traite le sujet des algorithmes adaptatifs utilisant le critère de cohérence. L'adaptation des éléments du dictionnaire en utilisant une méthode de gradient stochastique est abordée pour deux familles de fonctions noyau. Cette partie a un autre objectif qui est la dérivation des algorithmes adaptatifs utilisant le critère de cohérence pour identifier des modèles à sorties multiples.La deuxième partie introduit d'une manière abrégée le palier magnétique actif (PMA). La proposition de contrôler un PMA par un algorithme adaptatif à noyau est présentée pour remplacer une méthode utilisant les réseaux de neurones à couches multiples / Function approximation methods based on reproducing kernel Hilbert spaces are of great importance in kernel-based regression. However, the order of the model is equal to the number of observations, which makes this method inappropriate for online identification. To overcome this drawback, many sparsification methods have been proposed to control the order of the model. The coherence criterion is one of these sparsification methods. It has been shown possible to select a subset of the most relevant passed input vectors to form a dictionary to identify the model.A kernel function, once introduced into the dictionary, remains unchanged even if the non-stationarity of the system makes it less influent in estimating the output of the model. This observation leads to the idea of adapting the elements of the dictionary to obtain an improved one with an objective to minimize the resulting instantaneous mean square error and/or to control the order of the model.The first part deals with adaptive algorithms using the coherence criterion. The adaptation of the elements of the dictionary using a stochastic gradient method is presented for two types of kernel functions. Another topic is covered in this part which is the implementation of adaptive algorithms using the coherence criterion to identify Multiple-Outputs models.The second part introduces briefly the active magnetic bearing (AMB). A proposed method to control an AMB by an adaptive algorithm using kernel methods is presented to replace an existing method using neural networks

This master´s thesis deals an active elements called digitally controlled current amplifier, multiple-output current follower and its usage in tunable frequency filters. These tunable frequency filters operate in a pure current mode. In the first part of this work are presented the different types of current active elements. Universal current conveyor, multiple-output current follower, digitally controlled current amplifier (UCC, MO-CF, DCCA). In the second part of this work are introduced particular methods of design tunable frequency filters. Special attention is given to using the design method of via autonomous circuits because it is one of the most. In the last part of this thesis are designed and computer-simulated individual multifunction tunable frequency filters with those already active yet elements. These filters were designed via autonomous circuits or modification of existing circuits. The functionality of the proposed filtres have been verified by computer simulation. Snap3 program was used for the symbolic analyse of circuit and OrCad PSpice program was used to simulate the characteristics of multifunction filters.

This master´s thesis is about MO-CF, DCCA and CC frequency filters with current active elements proposal. Current active elements, their features, structure and utilization are shown in introduction. A progress propose of universal filter is described in thesis. With the use of active elements has been established an universal filter with basic parameter changes capability (quality and limit frequency). SNAP software was used in this propose and the characteristics simulation have been done in OrCad-PSpice. For control changes of quality and limit frequency was used active element DCCA. The main circuit board of universal controlled filter was made with the EAGLE software. Created sample was measured for each type of filter, the different quality and limit frequency. These values were compared with simulated values of the filter.

Spectrum, environment and location awareness are key characteristics of cognitive radio (CR). Knowledge of a user’s location as well as the surrounding environment type may enhance various CR tasks, such as spectrum sensing, dynamic channel allocation and interference management. This dissertation deals with the optimisation of adaptive localisation techniques for CR. The first part entails the development and evaluation of an efficient bandwidth determination (BD) model, which is a key component of the cognitive positioning system. This bandwidth efficiency is achieved using the Cramer-Rao lower bound derivations for a single-input-multiple-output (SIMO) antenna scheme. The performances of the single-input-single-output (SISO) and SIMO BD models are compared using three different generalised environmental models, viz. rural, urban and suburban areas. In the case of all three scenarios, the results reveal a marked improvement in the bandwidth efficiency for a SIMO antenna positioning scheme, especially for the 1×3 urban case, where a 62% root mean square error (RMSE) improvement over the SISO system is observed. The second part of the dissertation involves the presentation of a multiband time-of arrival (TOA) positioning technique for CR. The RMSE positional accuracy is evaluated using a fixed and dynamic bandwidth availability model. In the case of the fixed bandwidth availability model, the multiband TOA positioning model is initially evaluated using the two-step maximum-likelihood (TSML) location estimation algorithm for a scenario where line-of-sight represents the dominant signal path. Thereafter, a more realistic dynamic bandwidth availability model has been proposed, which is based on data obtained from an ultra-high frequency spectrum occupancy measurement campaign. The RMSE performance is then verified using the non-linear least squares, linear least squares and TSML location estimation techniques, using five different bandwidths. The proposed multiband positioning model performs well in poor signal-to-noise ratio conditions (-10 dB to 0 dB) when compared to a single band TOA system. These results indicate the advantage of opportunistic TOA location estimation in a CR environment. / Dissertation (MEng)--University of Pretoria, 2012. / Electrical, Electronic and Computer Engineering / unrestricted

This work concentrates on the application of diversity techniques and space time block coding for future high speed mobile wireless communications on multicarrier systems. At first, alternative multicarrier kernels robust for high speed doubly-selective fading channel are sought. They include the comparisons of discrete Fourier transform (DFT), fractional Fourier transform (FrFT) and wavelet transform (WT) multicarrier kernels. Different wavelet types, including the raised-cosine spectrum wavelets are implemented, evaluated and compared. From different wavelet families, orthogonal wavelets are isolated from detailed evaluations and comparisons as suitable for multicarrier applications. The three transforms are compared over a doubly-selective channel with the WT significantly outperforming all for high speed conditions up to 300 km/hr. Then, a new wavelet is constructed from an ideal filter approximation using established wavelet design algorithms to match any signal of interest; in this case under bandlimited criteria. The new wavelet showed better performance than other traditional orthogonal wavelets. To achieve MIMO communication, orthogonal space-time block coding, OSTBC, is evaluated next. First, the OSTBC is extended to assess the performance of the scheme over extended receiver diversity order. Again, with the extended diversity conditions, the OSTBC is implemented for a multicarrier system over a doubly-selective fading channel. The MIMO-OFDM systems (implemented using DFT and WT kernels) are evaluated for different operating frequencies, typical of LTE standard, with Doppler effects. It was found that, during high mobile speed, it is better to transmit OFDM signals using lower operating frequencies. The information theory for the 2-transmit antenna OSTBC does not support higher order implementation of multi-antenna systems, which is required for the future generation wireless communications systems. Instead of the OSTBC, the QO-STBC is usually deployed to support the design of higher order multi-antenna systems other than the 2-transmit antenna scheme. The performances of traditional QO-STBC methods are diminished by some off-diagonal (interference) terms such that the resulting system does not attain full diversity. Some methods for eliminating the interference terms have earlier been discussed. This work follows the construction of cyclic matrices with Hadamard matrix to derive QO-STBC codes construction which are N-times better than interference free QO-STBC, where N is the number of transmit antenna branches.

This work concentrates on the application of diversity techniques and space time block coding for future mobile wireless communications. The initial system analysis employs a space-time coded OFDM transmitter over a multipath Rayleigh channel, and a receiver which uses a selection combining diversity technique. The performance of this combined scenario is characterised in terms of the bit error rate and throughput. A novel four element QOSTBC scheme is introduced, it is created by reforming the detection matrix of the original QOSTBC scheme, for which an orthogonal channel matrix is derived. This results in a computationally less complex linear decoding scheme as compared with the original QOSTBC. Space time coding schemes for three, four and eight transmitters were also derived using a Hadamard matrix. The practical optimization of multi-antenna networks is studied for realistic indoor and mixed propagation scenarios. The starting point is a detailed analysis of the throughput and field strength distributions for a commercial dual band 802.11n MIMO radio operating indoors in a variety of line of sight and non-line of sight scenarios. The physical model of the space is based on architectural schematics, and realistic propagation data for the construction materials. The modelling is then extended and generalized to a multi-storey indoor environment, and a large mixed site for indoor and outdoor channels based on the Bradford University campus. The implications for the physical layer are also explored through the specification of antenna envelope correlation coefficients. Initially this is for an antenna module configuration with two independent antennas in close proximity. An operational method is proposed using the scattering parameters of the system and which incorporates the intrinsic power losses of the radiating elements. The method is extended to estimate the envelope correlation coefficient for any two elements in a general (N,N) MIMO antenna array. Three examples are presented to validate this technique, and very close agreement is shown to exist between this method and the full electromagnetic analysis using the far field antenna radiation patterns.

This thesis is concentrated on the Angle / Direction of Arrival (A/DOA) estimation and Beamforming techniques that can be used in the current and future engineering applications such as tracking of targets, wireless mobile communications, radar systems, etc. This thesis firstly investigates different types of AOA and beamforming techniques. A comprehensive comparison between the common AOA algorithms is performed to evaluate the estimation accuracy and illustrate the computational complexity of each algorithm. The effect of mutual coupling between the radiators and the impact of the position-error of the antenna elements on the estimation accuracy is also studied. Then, several new efficient AOA methods for current wireless localisation systems are proposed. The estimation accuracy and computational complexity are compared with well-known AOA methods over a wide range of scenarios. New methodologies for Covariance Matrix (CM) sampling are proposed to enhance and improve operational performance without increasing the computational burden. A new beamforming algorithm is proposed and implemented on a compact mm-Wave linear and planar antenna arrays to enhance the desired signal and suppress the interference sources in wireless communication systems. The issue of asset tracking in dense environments where the performance of the Global Positioning System (GPS) becomes unavailable or unreliable is addressed in the thesis as well. The proposed solution uses a low-profile array of sensors mounted on a finite conducting ground. A compact-size omnidirectional spiral sensor array of six electrically small dual-band antenna elements was designed to operate in the 402 and 837 MHz spectrum bands. For the lower band, a three-element superposition method is applied to support the estimated AOA whereas six sensors are considered for the higher band. An efficient and low complexity Projection Vector (PV) AOA method is proposed. An Orthogonal Frequency Division Multiplexing (OFDM) modulation is integrated with the PV technique to enhance the estimation resolution. The system was found to be suitable for installation on top of vehicles to localise the position of assets. The proposed system was tested to track non-stationary objectives, and then two scenarios were investigated: outdoor to outdoor and outdoor to indoor environments using Wireless In-Site Software. The results confirm that the proposed tracking system works efficiently with a single snapshot. / Higher Commission for Education Development (HCED) in Iraq Basra Oil Company Ministry of Oil

Multiple-Input-Multiple-Output (MIMO) antenna technology refers to an antenna with multiple radiators at both transmitter and receiver ends. It is designed to increase the data rate in wireless communication systems by achieving multiple channels occupying the same bandwidth in a multipath environment. The main drawback associated with this technology is the coupling between the radiating elements. A MIMO antenna system merely acts as an antenna array if the coupling between the radiating elements is high. For this reason, strong decoupling between the radiating elements should be achieved, in order to utilize the benefits of MIMO technology. The main objectives of this thesis are to investigate and implement several printed MIMO antenna geometries with integrated decoupling approaches for WLAN, WiMAX, and 5G applications. The characteristics of MIMO antenna performance have been reported in terms of scattering parameters, envelope correlation coefficient (ECC), total active reflection coefficient (TARC), channel capacity loss (CCL), diversity gain (DG), antenna efficiency, antenna peak gain and antenna radiation patterns. Three new 2×2 MIMO array antennas are proposed, covering dual and multiple spectrum bandwidths for WLAN (2.4/5.2/5.8 GHz) and WiMAX (3.5 GHz) applications. These designs employ a combination of DGS and neutralization line methods to reduce the coupling caused by the surface current in the ground plane and between the radiating antenna elements. The minimum achieved isolation between the MIMO antennas is found to be better than 15 dB and in some bands exceeds 30 dB. The matching impedance is improved and the correlation coefficient values achieved for all three antennas are very low. In addition, the diversity gains over all spectrum bands are very close to the ideal value (DG = 10 dB). The forth proposed MIMO antenna is a compact dual-band MIMO antenna operating at WLAN bands (2.4/5.2/5.8 GHz). The antenna structure consists of two concentric double square rings radiating elements printed symmetrically. A new method is applied which combines the defected ground structure (DGS) decoupling method with five parasitic elements to reduce the coupling between the radiating antennas in the two required bands. A metamaterial-based isolation enhancement structure is investigated in the fifth proposed MIMO antenna design. This MIMO antenna consists of two dual-band arc-shaped radiating elements working in WLAN and Sub-6 GHz 5th generation (5G) bands. The antenna placement and orientation decoupling method is applied to improve the isolation in the second band while four split-ring resonators (SRRs) are added between the radiating elements to enhance the isolation in the first band. All the designs presented in this thesis have been fabricated and measured, with the simulated and measured results agreeing well in most cases. / Higher Committee for Education Development in Iraq (HCED)

The fifth-generation (5G) wireless network has received a lot of attention from both academia and industry with many reported efforts. Multiple-input-multiple-output (MIMO) is the most promising wireless access technology for next-generation networks to provide high spectral and energy efficiency. For handheld devices such as smartphones, 2×2 MIMO antennas are currently employed in 4G systems and it is expected to employ a larger number of elements for 5G mobile terminals. Placing multiple antennas in the limited space of a smartphone PCB poses a significant challenge. Therefore, a new design technique using dual-polarized antenna resonators for 8×8 MIMO configuration is proposed for sub 6 GHz 5G applications. The proposed MIMO configuration could improve the channel capacity, diversity function, and multiplexing gain of the smartphone antenna system which makes it suitable for 5G applications. Different types of new and compact diversity MIMO antennas with Patch, Slot, and Planar inverted F antenna (PIFA) resonators are studied for different candidate bands of sub 6 GHz spectrum such as 2.6, 3.6, and 5.8 GHz. Unlike the reported MIMO antennas, the proposed designs provide full radiation coverage and polarization diversity with sufficient gain and efficiency values supporting different sides of the mainboard. Apart from the sub 6 GHz frequencies, 5G devices are also expected to support the higher bands at the centimeter/millimeter-wave spectrums. Compact antennas can be employed at different portions of a smartphone board to form linear phased arrays. Here, we propose new linear phased arrays with compact elements such as Dipole and Quasi Yagi resonators for 5G smartphones. Compared with the recently reported designs, the proposed phased arrays exhibit satisfactory features such as compact size, wide beam steering, broad bandwidth, end-fire radiation, high gain, and efficiency characteristics. The proposed 5G antennas can provide single-band, multi-band, and broad-band characteristics with reduced mutual coupling function. The fundamental characteristics of the 5G antennas are examined using both simulations and measurements and good agreement is observed. Furthermore, due to compact size and better placement of elements, quite good characteristics are observed in the presence of the user and the smartphone components. These advantages make the proposed antennas highly suitable for use in 5G smartphone applications. / European Union Horizon 2020 Research and Innovation Programme under grant agreement H2020-MSCA-ITN-2016 SECRET-722424