No description available.

No description available.

No description available.

No description available.

<p>The entrapment of biomolecules within TEOS-based sol-gel derived organic/inorganic nanocomposite materials has proven to be a viable platform for the development of biosensors and solid-phase biocatalysts. In this thesis, a series of organically modified silica materials were prepared by a two-step aqueous processing method that was suitable for biomolecule entrapment, and were formed as submicron thick films by dipcasting. Dispersed additives, such as polymers (Class I materials) and covalently bound additives, such as organically modified silanes (Class II materials), were used to modify the internal environment compared to the undoped matrices and to correlate the properties of entrapped enzymes.</p> <p>The morphology of organically modified silica materials could be modified through the use of either separate or co-hydrolysis of the silane precursors, with the later method generating optically transparent materials. Fluorescence microscopy revealed chemical heterogeneity in materials that appeared to be homogeneous by brightfield or SEM.</p> <p>Fluorescence emission studies of a solvatochromic dye entrapped within the film confirmed that the internal chemical environment of the films was strongly affected by doping with polymers and organosilanes. The films showed a rapid initial change in chemical properties owing to solvent evaporation, followed by a much slower evolution over several months owing to continued condensation reactions within the film.</p> <p>A reagentless biosensor was designed based on co-entrapment of an enzyme and a fluorescently labeled polymer. The enzymes urease and lipase were selected for this study as both catalyze reactions that alter the local pH. By co-entrapping pH sensitive fluorophores (SNARF-I and fluorescein) bound to a high molecular weight polymer, it was possible to detect the analytes urea and glyceryl tributyrate using changes in the fluorescence intensity (fluorescein) or emission ratio (SNARF-l). By tuning the polarity of the matrix it was possible to optimize the sensitivity of the sensing film for both the polar and non-polar analyte.</p> / Doctor of Philosophy (PhD)

Polymer composites are fast becoming a material in the manufacturing of automotive interior and exterior parts such as facias and dashboard components. Production of rigid structural foams are ideal because they reduce the overall weight as well as reduce the amount of material used to manufacture the part. Polymer-clay nanocomposites are a classification of materials containing a blend of polymer and a small weight percentage of nanoclay. These materials are currently of interest to automotive part manufacturers because they are known to deliver improved mechanical properties and increase foamability of a polymer. The current study investigates the changes in material properties and the foamability of a thermoplastic polyolefin (TPO)-clay nanocomposite as the degree of intercalation was varied. The TPO-clay nanocomposite was produced by melt blending TPO, nanoclay and maleic anhydride grafted polypropylene (MAHgPP) in a co-rotating twin screw extruder. The material was subjected to a multi-pass process to vary the degree of intercalation. Degree of intercalation was tracked by rheology, XRD and TEM micrographs. Part density, cell density and flexural modulus measurements were performed on foamed and non-foamed injection molded bars to observe changes in the foamability of the material. Material was also processed without clay and analyzed in the same manner. Through TEM and XRD analysis it was found that the degree of intercalation and delamination was varied with increasing number of passes. Rheological measurements showed that the TPO-clay nanocomposite underwent (beta)-scission and intercalation simultaneously. The changes in intercalation had a positive effect on the foamability of the TPO-clay nanocomposite. As well, the TPO-clay nanocomposite experienced an increase in flexural properties for both unfoamed and foamed parts compared to the TPO-PPgMAH blend; TPO-clay nanocomposite experienced a 44% and 23% increase in the flexural modulus for unfoamed and foamed parts respectively. Data also showed that there was a limit to the number of times the TPO-clay nanocomposite can be recycled before the foamability of the material begins to decrease, which was attributed to material degradation. / Thesis / Master of Applied Science (MASc)

Natural composites like wood are scale-integrated structures that range from molecular to the macroscopic scale. Inspired by this design, layer-by-layer (LbL) deposition technique was used to create lignocellulosic composites from isolated wood polymers namely cellulose and lignin, with a lamellar architecture. In the first phase of the study, adsorption of alkali lignin onto cationic surfaces was investigated using a quartz crystal microbalance with dissipation monitoring (QCM-D). Complete coverage of the cationic surface with alkali lignin occured at low solution concentration; large affinity coefficients were calculated for this system at differing pH levels. Adsorption studies with organosolv lignin in an organic solvent, and spectroscopic analysis of mixtures of cationic polymer with alkali lignin revealed a non-covalent interaction. The work demonstrated how noncovalent interactions could be exploited to molecular organize thin polyphenolic biopolymers on cationic surfaces. The second phase of the study examined the adsorption steps during the LbL assembly process to create novel lignocellulosic composites. LbL assembly was carried out using oxidized nanocellulose (NC) and lignin, along with a cationic polymer poly(diallyldimethylammonium chloride) (PDDA). QCM-D was used to follow the sequential adsorption process of the three different polymers. Two viscoelastic models, namely Johannsmann and Voigt, were respectively used to calculate the areal mass and thickness of the adsorbed layers. Atomic force microscopy studies showed a complete coverage of the surface with lignin in all the disposition cycles, however, surface coverage with NC was seen to increase with the number of layers. Free-standing composite films were obtained when the LbL process was carried out for 250 deposition cycles (500 bilayers) on a cellulose acetate substrate, following the dissolution of the substrate in acetone. Scanning electron microscopy of the cryo-fractured cross-sections showed a lamellar structure, and the thickness per adsorption cycle was estimated to be 17 nm. The third phase of the study investigated the effect of LbL ordering of the polymers versus a cast film composed of a blended mixture of the polymers, using dynamic mechanical analysis. A tan ï ¤ peak was observed in the 30 – 40 ºC region for both films, which was observed in the neat NC film. Heating of the samples under a compressive force produced opposite effects in the films, as the LbL films exhibited swelling, whereas the cast films showed densification. The apparent activation energy of this transition (65 – 80 kJ mol-1) in cast films, calculated based on the Arrhenius equation was found to be coincident to those reported for the ï ¢ transition of amorphous cellulose. The peak was seen to disappear in case of LbL films in the second heat, whereas it was recurring in case of cast films of the blended mixture, and neat NC films. Altogether, the together the work details a novel path to integrate an organized lignin and cellulose molecular structure, albeit modified from their native form, into a three-dimensional composite material. / Ph. D.

Cellulose nanomaterials (CNMs) have been widely studied for their potential as sustainable fillers in polymer nanocomposites, optical responsiveness in suspensions and thin films, and their orientation-dependent liquid crystalline behavior in suspensions. Cellulose nanocrystals (CNCs) have seen a particular prominence due to their versatility across a breadth of applications. The unique structure of CNCs, represented as nanoscale rods with a slight twist, provides for their self-assembly into liquid crystalline phases when their concentration is increased and can be used to generate iridescent materials with tunable wavelengths. Further, CNCs are often used as fillers in nanocomposites, due to their high single crystal Young's modulus, achieving vast enhancements in stiffness when incorporated above a critical concentration where a percolating network is formed. The breadth of applications for CNCs strongly depend not only on their crystalline structure, but crucially on the interactions between particles. These interactions are well-known, yet a complete understanding to enable the full exploitation of the properties attainable in CNC-based materials is lacking. The principal emphasis of this dissertation lies in further improving our comprehension of the interactions between CNCs across a variety of applications such that their full potential can be achieved. A review of the current research of CNC-based materials is provided to guide the discussion herein. Interparticle interactions are studied in aqueous suspensions of CNCs in evaporating sessile droplets. This system provides a complex interrelationship between mass, heat, and momentum transport which collectively provide a change in the local CNC concentration as a function of time. CNC interactions can be controlled throughout the evaporation process as a result of these local concentration variations. We implement a novel approach using time-resolved polarized light microscopy to characterize the evolution of these particle interactions via the orientation of CNCs as a function of CNC concentration and droplet volume. Ultimately, boundary interactions at the leading edge of the contact line during evaporation was found to drive a cascade of local CNC interactions resulting in alignment post-deposition. Computational analysis evaluated the influence of evaporation-induced shear flow during evaporation. Orientation was found to be independent of the bulk fluid flow, corroborating the importance of interparticle interactions on the ensuing alignment of CNCs. Characterization of an evaporating droplet of initially liquid crystalline suspension of CNCs verified the simulations which predicted that orientation was not coupled with entrainment. Finally, the multiple modes of orientation showed that local control over CNC properties can be realized through governance of the interactions between CNCs. The interactions of CNCs in polymer nanocomposites were also studied for the development of smart materials which can adapt their properties in response to external stimuli. A well-known example of this phenomena is found when CNCs are introduced as fillers in thermoplastic polyurethanes (TPUs) above a critical concentration required to achieve percolation. The interactions between CNCs in the percolating network provide a strong enhancement to the modulus of these materials. However, these materials soften upon exposure to water following the disruption of inter-CNC hydrogen bonding by the diffusing water molecules, as prevailing theories suggest. CNCs simultaneously enhance water transport into hydrophobic matrices. Thus, a complete understanding of the interrelationship between the mass transport and mechanical performance can facilitate the development of humidity sensing or shape memory materials which operate as a result of the interactions between CNCs inside of a polymer matrix. Despite an increase in the equilibrium water uptake with increasing CNC concentration, a decrease in the apparent diffusivity of water within the nanocomposites was observed as a result of swelling of the bulk polymer. Additionally, we developed a modification to the commonly used percolation model to predict the time-dependent evolution of storage modulus during water-induced softening. We found that the solvent mass transport can be directly coupled to the mechanical integrity of the percolating network of CNCs by evaluating the hydrogen bonding state of the network as a function of time. Finally, a novel nanocomposite filler comprised of CNCs and 2,2,6,6- tetramethylpiperidine 1-oxyl (TEMPO) oxidized cellulose nanofibrils (TOCNFs) was prepared through solution casting to improve the mechanical performance of the individual reinforcements alone. The physical interaction length is increased by incorporating CNMs of different length scales resulting in increased tensile strength and elongation. Further, the morphology, evaluated with polarized light microscopy, atomic force microscopy, and simulated with dissipative particle dynamics, revealed the combined fillers exhibit a cooperative enhancement between CNMs. Characterization of the crystallinity through x-ray diffraction confirmed the interactions occur primarily between the crystalline domains of each material. Accordingly, the combination of CNMs resulted in nanocomposite fillers which can be implemented such that the weak interfaces with polymer matrices can be bridged with fillers providing reinforcement over a broader length scale. / Doctor of Philosophy / Cellulose nanocrystals (CNCs) are sustainable and biorenewable nanoparticles derived from cellulose. These materials have been widely studied and are commonly used among a plethora of applications such as in reinforcing fillers in polymer nanocomposites, optically responsive materials that can be used in packaging or anti-counterfeiting technologies, as well as in suspension modifiers for skin care products. These techniques tune the interactions between individual CNCs to modify the behavior of the bulk material. The specific interactions are well-known, yet a complete understanding of the influence of these interactions resulting in the utility of CNC-based materials in various applications is lacking. The principal emphasis of this dissertation lies in further improving our comprehension of the interactions between CNCs across a variety of applications such that their full potential can be achieved. Interactions between CNCs were investigated in three systems comprising of a range of typical use cases for CNC-based materials. The behavior of CNCs was examined in evaporating droplets of aqueous suspensions. These materials exhibited a change in orientation in the final deposit which is dependent on variations in local CNC concentration during drying. These concentration changes describe the relative strength of interactions between CNCs which ultimately influences the final alignment of these materials. Further, these interactions provide a pathway to deposit a controlled orientation of CNCs on a substrate which can be utilized for optically responsive materials or serve as templates for other orientation-dependent materials. CNCs were also incorporated into a thermoplastic polyurethane (TPU) matrix to provide increased stiffness. In these composites, water preferentially interacts with CNCs preventing the nanoparticles from interacting with one another. As water is absorbed, these materials soften as a result of the reduced interactions between CNCs. We investigated the influence of dynamically changing CNC interactions on the mechanical performance of these materials during water absorption and developed an analytical model to describe the observed softening behavior. Finally, CNCs were combined with 2,2,6,6- tetramethylpiperidine 1-oxyl oxidized cellulose nanofibers (TOCNFs) and cast into thin films. The mechanical properties of these differently sized, yet chemically similar, nanoparticles were compared as a function of CNC composition. A cooperative enhancement of the ultimate tensile strength and elongation was observed at low CNC loadings where CNCs and TOCNFs were found to self-organize during casting in a mutually beneficial manner.

Projection Stereolithography (PSL) is an Additive Manufacturing process that digitally patterns light to selectively expose and layer photopolymer into three dimensional objects. Nanomaterials within the photopolymer are therefore embedded inside fabricated objects. Adding varying concentrations of multi-walled carbon nanotubes (MWCNT) to the photopolymer may allow for the engineering of an objects tensile strength and electric conductivity. This research has two goals (i) the fabrication of three-dimensional structures using PSL and (ii) the material characterization of nanocomposite photopolymers. A morphological matrix design tool was developed and used to categorically analyze published PSL systems. These results were used to justifying design tradeoffs during the design and fabricate of a new PSL system. The developed system has 300μm resolution, 45mm x 25mm fabrication area, 0.23mW/cm2 intensity, and 76.2mm per hour vertical build rate. Nanocomposite materials were created by mixing Objet VeroClear FullCure 810 photopolymer with 0.1, 0.2, and 0.5 weight percent MWCNT using non-localized bath sonication. The curing properties of these nanocomposite mixtures were characterized; adding 0.1 weight-percent MWCNT increases the critical exposure by 10.7% and decreases the depth of penetration by 40.1%. The material strength of these nanocomposites were quantified through tensile testing; adding 0.1 weight-percent MWCNT decreases the tensile stress by 45.89%, the tensile strain by 33.33%, and the elastic modulus by 28.01%. Higher concentrations always had exaggerated effects. Electrical conductivity is only measurable for the 0.5 weight-percent nanocomposite with a 8k/mm resistance. The 0.1 weight-percent nanocomposite was used in the PSL system to fabricate a three-dimensional nanocomposite structure. / Master of Science

Cost-effective purification and desalination of water is a global challenge. Reverse osmosis (RO), the current method of choice, requires high pressure drops across the membranes in order to achieve acceptably high flow rates. Conventional polymer membranes are limited in their performance by a trade-off between water permeability and water/salt selectivity. Biofilm fouling is another critical problem in RO applications. Recent simulations and experiments suggest that properly functionalized carbon nanotubes (CNTs) can be used to construct RO membranes that have high permeation flux as well as complete ion rejection, and that are resistant to biofilm formation. The objective of this research was to combine zwitterion-functionalized carbon nanotubes with traditional thin film polyamide (PA) to fabricate a novel desalination membrane which has both high permeability as well as selectivity. Zwitterion functional groups in CNTs act as molecular gatekeepers at the entrance of the nanotubes to enhance blockage for salt ions. Functionalized CNTs were oriented on a membrane support by high vacuum filtration. These oriented CNTs were sealed by a polyamide film via interfacial polymerization. Cross-sectional image of the nanocomposite membrane taken by scanning electron microscopy (SEM) showed semi-aligned zwitterion-CNTs on top of a porous support covered by a thin PA film with an overall thickness of approximately 250 nm. When the concentration of zwitterion-CNTs in the membrane increased, the nanocomposite membranes experienced significant improvement in permeation flux while the ion rejection increases slightly or remains unchanged. This indicated that the increased water flux is not due to an increase in nonspecific pores in the membrane, but rather due to an additional transport mechanism resulting from the presence of the functionalized CNTs. Significant increase of flux was also observed in separating cations other than sodium. The separation of the PA skin layer dominated the ion rejection mechanism by size exclusion even when the carbon nanotubes were introduced into the polyamide coating. The zwitterion functional groups exposed at the membrane surface also interacted with the feed water to form a strong hydration layer, which results in improved surface biofouling resistance. The adsorption rate of protein foulants on the nanocomposite membrane surface was significantly reduced compared to the control membrane without CNTs, and the adsorbed fouling layer could be easily removed by flushing with water. After washing, the nanocomposite membrane recovered 100% of the decreased water flux whereas the control membrane only recovered 10% of the decreased flux resulting in a permanent loss of 30% in water permeation. We have therefore demonstrated that advanced materials like CNTs can be synthesized with desired functional groups, and can be embedded into traditional RO membranes to simultaneously resolve the challenge of low flux and surface fouling in the current desalination process. / Ph. D.