International Telemetering Conference Proceedings / October 27-30, 1997 / Riviera Hotel and Convention Center, Las Vegas, Nevada / This paper describes the two main causes of fading encountered at test ranges. The first cause of fading results from nulls in the transmit antenna gain pattern. Variations in the received signal level are a result of changes in the gain pattern as the spatial relationship between transmitter and receiver change. The second cause of fading is due to multipath interference. This occurs when multiple copies of the transmitted signal with different delays arrive at the receiver and are phased relative to each other so that destructive interference occurs.

This thesis reports the methods, the deployment strategies and the resulting system performance improvement of in-building environmental modification. With the increasing use of mobile computing devices such as PDAs, laptops, and the expansion of wireless local area networks (WLANs), there is growing interest in increasing productivity and efficiency through enhancing received signal power. This thesis proposes the deployment of waveguides consisting of frequency selective surfaces (FSSs) in indoor wireless environments and investigates their effect on radio wave propagation. The received power of the obstructed (OBS) path is attenuated significantly as compared with that of the line of sight (LOS) path, thereby requiring an additional link budget margin as well as increased battery power drain. In this thesis, the use of an innovative model is also presented to selectively enhance radio propagation in indoor areas under OBS conditions by reflecting the channel radio signals into areas of interest in order to avoid significant propagation loss. An FSS is a surface which exhibits reflection and/or transmission properties as a function of frequency. An FSS with a pass band frequency response was applied to an ordinary or modified wall as a wallpaper to transform the wall into a frequency selective (FS) wall (FS-WALL) or frequency selective modified wall (FS-MWALL). Measurements have shown that the innovative model prototype can enhance 2.4GHz (IEEE 802.11b/g/n) transmissions in addition to the unmodified wall, whereas other radio services, such as cellular telephony at 1.8GHz, have other routes to penetrate or escape. The FSS performance has been examined intensely by both equivalent circuit modelling, simulation, and practical measurements. Factors that influence FSS performance such as the FSS element dimensions, element conductivities, dielectric substrates adjacent to the FSS, and signal incident angles, were investigated. By keeping the elements small and densely packed, a largely angle-insensitive FSS was developed as a promising prototype for FSS wallpaper. Accordingly, the resultant can be modelled by cascading the effects of the FSS wallpaper and the ordinary wall (FSWALL) or modified wall (FS-MWALL). Good agreement between the modelled, simulated, and the measured results was observed. Finally, a small-scale indoor environment has been constructed and measured in a half-wave chamber and free space measurements in order to practically verify this approach and through the usage of the deterministic ray tracing technique. An initial investigation showing that the use of an innovative model can increase capacity in MIMO systems. This can be explained by the presence of strong multipath components which give rise to a low correlated Rayleigh Channel. This research work has linked the fields of antenna design, communication systems, and building architecture.

International Telemetering Conference Proceedings / October 30-November 02, 1995 / Riviera Hotel, Las Vegas, Nevada / This paper will discuss the performance of pulse code modulation (PCM)/frequency modulation (FM) during frequency selective fading. Frequency selective fading occurs when the attenuation in part of the frequency band of interest is much greater than in the rest of the band of interest. The frequency selective fading model used in this paper assumes that two paths with different delays exist between the transmitter and receiver (multipath). The two-path model was simulated in the laboratory and the effects of frequency selective fading on the radio frequency (RF) spectrum and on the waveforms at the output of the FM demodulator were measured. A mathematical model was also used to predict the effects of frequency selective fading. The predicted waveshapes are compared with the laboratory data. A simple demodulator which alleviates the effects of frequency selective fading on PCM/FM at moderate signal-to-noise ratios (SNRs) will be described. This demodulator is created by detuning the telemetry receiver by a frequency equal to approximately one-half of the intermediate frequency (IF) bandwidth and using the receiver’s amplitude modulation (AM) detector output rather than the FM detector output. The performance of this offset AM demodulator will be compared with the performance of an FM demodulator. Frequency selective fades measured in real-world environments will be also presented.

No description available.

This thesis reviews the role of emotions in one’s choice of information, information processing, and political attitudes. Theoretical and empirical endeavors to date have focused primarily on how emotions influence attitudes and information processing, leaving the actual processes guiding these outcomes in the margins. Specifically, it has been largely unexplored how emotions influence individuals’ information search behavior and then attitudes and information processing. Noting that the purposeful selection of likeminded information, often referred to as selective exposure, is commonly enacted when an individual first initiates information processing, and is also likely influenced by emotions, this study explores how emotions may affect people’s tendency to seek out congruent information. In addition, this study examines how the relationship between emotions and selective exposure in turn may affect aspects of information processing and attitudes. By designing an online experiment, I first tested how certain negative emotions (anger/fear) affected one’s pursuit of certain types of information (consistent/inconsistent) and second, I investigated how these emotions and information selections influenced subsequent information processing and attitudes. Results showed that while anger motivated more likeminded exposure for Republicans than fear, fear promoted more likeminded exposure for Democrats than anger. Further, anger prompted people to process messages more closely and to develop more polarized attitudes compared to fear. In addition, pro-attitudinal exposure produced more message-relevant thoughts for Republicans than counter-attitudinal message exposure, while it was counter-attitudinal exposure that yielded more message-relevant thoughts for Democrats. No such effect, however, was shown for attitudinal polarization. / text

Electrolessly deposited CoWP capping layers have been demonstrated to effectively reduce electromigration of Cu at the interconnect/dielectric-barrier cap interface while reducing resistivity relative to SiCN. However, as device dimensions scale, the need for alternative methods for the selective deposition of sub-5 nm, ultrathin, conformal Co capping layers is apparent. To develop methods for area-selective atomic layer deposition (AS-ALD) of Co caps for next-generation Cu interconnects, the ALD behavior of bis(N-tert-butyl-N’-ethylpropionamidinato) cobalt(II) (CoAMD) is evaluated on Cu, SiO₂, and a porous low-k ( ~2.6) dielectric, CDO. The first and second ALD half reactions of CoAMD on the respective substrates is evaluated with H₂ coreactant by adsorbing the precursor on the substrates under ALD cycling conditions at 265 °C with and without coreactant exposure. The adsorption studies indicate that CoAMD preferentially deposits most on Cu and least on CDO. Further, CoAMD, like other amidinate precursors, readily dissociates on the Cu transition metal surface but the ultimate per-cycle coverage is self-limited by the slow desorption of amidinate ligands and fragments from the Cu surface. Co films deposited by ALD from CoAMD on Cu at 265 °C indicate that Co burrows into the lower energy Cu surface as the film grows in order to reduce the free surface energy. The Cu remains as a surfactant-like layer on the topmost Co surface up to film thicknesses of at least 16 nm. Moreover, considerable intermixing at the Co/Cu interface and Cu concentration several nm into the Co films are observed indicating high surface mobility of the two materials and Cu diffusion at polycrystalline Co grain boundaries. Finally, employing low-tempurature ALD and selectively passivating the dielectric surfaces with OH targeting passivants leads to enhanced selectivity of CoAMD for deposition on Cu versus SiO₂ and CDO. Depositing Co from CoAMD on Cu and CDO at 165 °C after 500 kTorr-s exposure to trimethylchlorosilane at 50 °C leads to a 30:1 preference for Co accumulation on Cu, a twelve times improvement compared to deposition on cleaned Cu and CDO at 265 °C. / text

No description available.

No description available.

No description available.

No description available.