Diese Arbeit befasst sich mit der Synthese und der Charakterisierung von thermoresponsiven Polymeren und ihrer Immobilisierung auf festen Oberflächen als nanoskalige dünne Schichten. Dabei wurden thermoresponsive Polymere vom Typ der unteren kritischen Entmischungstemperatur (engl.: lower critical solution temperature, LCST) verwendet. Sie sind bei niedrigeren Temperaturen im Lösungsmittel gut und nach Erwärmen oberhalb einer bestimmten kritischen Temperatur nicht mehr löslich; d. h. sie weisen bei einer bestimmten Temperatur einen Phasenübergang auf. Als Basismaterial wurden verschiedene thermoresponsive und biokompatible Polymere basierend auf Diethylenglykolmethylethermethacrylat (MEO2MA) und Oligo(ethylenglykol)methylethermethacrylat (OEGMA475, Mn = 475 g/ mol) über frei radikalische Copolymerisation synthetisiert. Der thermoresponsive Phasenübergang der Copolymere wurde in wässriger Lösung und in gequollenen vernetzten dünnen Schichten beobachtet. Außerdem wurde untersucht, inwiefern eine selektive Proteinbindung an geeignete funktionalisierte Copolymere die Phasenübergangstemperatur beeinflusst. Die thermoresponsiven Copolymere wurden über photovernetzbare Gruppen auf festen Oberflächen immobilisiert. Die nötigen lichtempfindlichen Vernetzereinheiten wurden mittels des polymerisierbaren Benzophenonderivates 2 (4 Benzoylphenoxy)ethylmethacrylat (BPEM) in das Copolymer integriert. Dünne Filme der Copolymere mit ca. 100 nm Schichtdicke wurden über Rotationsbeschichtung auf Siliziumwafer aufgeschleudert und anschließend durch Bestrahlung mit UV Licht vernetzt und auf der Oberfläche immobilisiert. Die Filme sind stabiler je größer der Vernetzeranteil und je größer die Molmasse der Copolymere ist. Bei einem Waschprozess nach der Vernetzung wird beispielsweise aus einem Film mit moderater Molmasse und geringem Vernetzeranteil mehr unvernetztes Copolymer ausgewaschen als bei einem höhermolekularen Copolymer mit hohem Vernetzeranteil. Die Quellbarkeit der Polymerschichten wurde mit Ellipsometrie untersucht. Sie ist größer je geringer der Vernetzeranteil in den Copolymeren ist. Schichten aus thermoresponsiven OEG Copolymeren zeigen einen Volumenphasenübergang vom Typ der LCST. Der thermoresponsive Kollaps der Schichten ist komplett reversibel, die Kollapstemperatur kann über die Zusammensetzung der Copolymere eingestellt werden. Für einen Vergleich dieser Eigenschaften mit dem gut charakterisierten und derzeit wohl am häufigsten untersuchten thermoresponsiven Polymer Poly(N-isopropylacrylamid) (PNIPAM) wurden zusätzlich photovernetzte Schichten aus PNIPAM hergestellt und ebenfalls ellipsometrisch vermessen. Im Vergleich zu PNIPAM verläuft der Phasenübergang der Schichten aus den Copolymeren mit Oligo(ethylenglykol)-seitenketten (OEG Copolymere) über einen größeren Temperaturbereich. Mit Licht einer Wellenlänge > 300 nm wurden die photosensitiven Benzophenongruppen selektiv angeregt. Bei der Verwendung kleinerer Wellenlängen vernetzten die Copolymerschichten auch ohne die Anwesenheit der lichtempfindlichen Benzophenongruppen. Dieser Effekt ließ sich zur kontrollierten Immobilisierung und Vernetzung der OEG Copolymere einsetzen. Als weitere Methode zur Immobilisierung der Copolymere wurde die Anbindung über Amidbindungen untersucht. Dazu wurden OEG Copolymere mit dem carboxylgruppenhaltigen 2 Succinyloxyethylmethacrylat (MES) auf mit 3 Aminopropyldimethylethoxysilan (APDMSi) silanisierte Siliziumwafer rotationsbeschichtet, und mit dem oligomeren α, ω Diamin Jeffamin® ED 900 vernetzt. Die Vernetzungsreaktion erfolgte ohne weitere Zusätze durch Erhitzen der Proben. Die Hydrogelschichten waren anschließend stabil und zeigten neben thermoresponsivem auch pH responsives Verhalten. Um zu untersuchen, ob die Phasenübergangstemperatur durch eine Proteinbindung beeinflusst werden kann, wurde ein polymerisierbares Biotinderivat 2 Biotinyl-aminoethylmethacrylat (BAEMA) in das thermoresponsive Copolymer eingebaut. Der Einfluss des biotinbindenen Proteins Avidin auf das thermoresponsive Verhalten des Copolymers in Lösung wurde untersucht. Die spezifische Bindung von Avidin an das biotinylierte Copolymer verschob die Übergangstemperatur deutlich zu höheren Temperaturen. Kontrollversuche zeigten, dass dieses Verhalten auf eine selektive Proteinbindung zurückzuführen ist. Thermoresponsive OEG Copolymere mit photovernetzbaren Gruppen aus BPEM und Biotingruppen aus BAEMA wurden über Rotationsbeschichtung auf Gold- und auf Siliziumoberflächen aufgetragen und durch UV Strahlung vernetzt. Die spezifische Bindung von Avidin an die Copolymerschicht wurde mit Oberflächenplasmonenresonanz und Ellipsometrie untersucht. Die Bindungskapazität der Schichten war umso größer, je kleiner der Vernetzeranteil, d. h. je größer die Maschenweite des Netzwerkes war. Die Quellbarkeit der Schichten wurde durch die Avidinbindung erhöht. Bei hochgequollenen Systemen verursachte eine Mehrfachbindung des tetravalenten Avidins allerdings eine zusätzliche Quervernetzung des Polymernetzwerkes. Dieser Effekt wirkt der erhöhten Quellbarkeit durch die Avidinbindung entgegen und lässt die Polymernetzwerke schrumpfen. / This work describes the synthesis and characterization of thermoresponsive polymers and their immobilisation on solid substrates as nanoscale thin films. The used polymers were of the lower critical solution temperature (LCST) type. They are well soluble in a solvent below a and get insoluble above a certain temperature, thus they exhibit a phase transition at a critical temperature. Different thermoresponsive biocompatible copolymers based on oligo(ethylene glycol) methyl ether methacrylate (OEGMA475) and di(ethylene glycol) methyl ether methacrylate (MEO2MA) were synthesized by free radical polymerization. The phase transition was observed in solution and in thin immobilized copolymer layers. Further regarding the phase transition the influence of selective protein binding onto functionalized copolymers was studied. Solid surfaces were modified with thermoresponsive copolymers based on MEO2MA, OEGMA475 and 2 (4 benzoylphenoxy)ethyl methacrylate (BPEM) as photo crosslinkable groups. Thin films of 100 nm thickness were spin-casted onto silicon wafers and subsequently crosslinked and immobilized by irradiation with UV-light. Their stability is controlled by the crosslinker ratio and by the molar mass of the copolymers. For instance a washing process after crosslinking removes more unbound polymer if the polymer contains less crosslinker and has a lower molecular weight. The swellability of the films was investigated by ellipsometry. It gets higher with lower crosslinker ratio. Layers of thermoresponsive copolymers exhibited a swelling/ deswelling phase transition of the lower critical solution temperature (LCST) type. The transition is completely reversible and the transition temperature can be adjusted by the composition of the copolymers. Compared to similarly synthesized photo-crosslinked layers of the well investigated thermoresponsive copolymer poly-(N-isopropyl acrylamide) (PNIPAM) the phase transition exceeds a larger temperature range. The photo-crosslinking of the OEG copolymers was accomplished in a controlled manner with light of wavelengths > 300 nm. Light of smaller wavelengths crosslinked the copolymer layers even without the presence of photosensitive groups. This effect could be exploited for a controlled immobilization and crosslinking of the OEG copolymers. As further method for crosslinking the formation of amide bonds was investigated. Therefore OEG copolymers containing 2 succinyloxyethyl methacrylate (MES) were spin-casted onto silicon substrates silanized with (3 aminopropyl)dimethylethoxysilane (APDMSi) and crosslinked with oligomeric α, ω diamine Jeffamin® ED 900. The crosslinking reaction was carried out by annealing the dry substrate. No further additives were added for the reaction. After annealing the hydrogel layers were stable against washing and showed thermoresponsive and pH responsive behaviour. In order to investigate whether the phase transition can be affected by specific protein binding, a polymerizable biotin derivative biotinyl-2-aminoethyl methacrylate (BAEMA) was integrated into the base thermoresponsive OEG copolymer. The influence of avidin on its thermoresponsive behaviour was investigated. The specific binding of avidin to the bioitinylated copolymer caused a marked shift of the transition temperature to higher temperatures. Control experiments proved that this effect can be ascribed to a specific protein binding. Thermoresponsive OEG Copolymers with photo-crosslinkable groups from BPEM and biotin groups from BAEMA were spin casted onto gold and silicon substrates and subsequently crosslinked by irradiation with UV light. The specific binding of Avidin onto the copolymer layer was investigated by surface plasmon resonance spectroscopy and ellipsometry. The binding capacity was higher if the mesh size of the hydrogel layers was higher. Upon binding of the Avidin the swellability of the layers was increased. At temperatures below the phase transition for loosely crosslinked copolymer layers an additional crosslinking effect of Avidin was observed. This effect counteracts the swelling of the hydrogel and leads to a shrinkage of the hydrogel layer.

<p>This work focused on grafting water-soluble polymers with well-controlled properties such as tuneable polymer chain length and high graft density to improve the biocompatibility of polymer surfaces via surface-initiated atom transfer radical polymerization (s-ATRP); and on gaining improved fundamental understanding of the mechanisms and factors (e.g., graft chain length and surface density of monomer units) in protein resistance of the water-soluble grafts.</p><p>Protein-resistant polyurethane (PU) surfaces were prepared by grafting watersoluble polymers including poly(oligo(ethylene glycol) methacrylate) (poly(OEGMA)) and poly(l-methacryloyloxyethyl phosphorylcholine) (poly(MPC)) via s-ATRP. A typical three-step procedure was used in the ATRP grafting. First, the substrate surface was treated in an oxygen plasma and reactive sites (-OH and -OOH) were formed upon exposure to air. Second, the substrate surface was immersed in 2-bromoisobutyryl bromide (BffiB)-toluene solution to form a layer of ATRP initiator. Finally, target polymer was grafted from the initiator-immobilized surface by s-ATRP with Cu(I)Br/2bpy complex as catalyst. The graft chain length was adjusted by varying the molar ratio of monomer to sacrificial initiator in solution. The modified PU surfaces were characterized by water contact angle, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM).</p><p>Protein adsorption experiments were carried out to evaluate the protein resistance of the surfaces. Adsorption from single and binary protein solutions as well as from plasma decreased significantly after poly(OEGMA) grafting, and decreased with increasing poly(OEGMA) main chain length. Fibrinogen (Fg) adsorption on the most resistant surfaces (chain length 200 units) was in the range of 3-33 ng/cm^2, representing a reduction of more than 96% compared to the control surfaces.</p><p>OEGMA monomers with three different molecular weights (MW 300, 475, 1100 g/mol) were used to achieve different side chain lengths of poly(OEGMA). Fibrinogen (Fg) and lysozyme (Lys) were used as model proteins in adsorption experiments. The effects of side chain length as well as main chain length were then investigated. It was found that adsorption to the poly(OEGMA)-grafted PU (PU/PO) surfaces was protein size dependent. Resistance was greater for the larger protein. For grafts of a given side chain length, the adsorption of both proteins decreased with increasing polymer main chain length. For a given main chain length, the adsorption of Fg, the larger protein, was independent of side chain length. Surprisingly, however, Lys (the smaller protein) adsorption increased with increasing side chain length. A reasonable explanation is that graft main chain density decreased as monomer size and footprint on the surface increased. Protein size-based discrimination suggests that the chain density was lower than required to form layers in the "brush" regime in which protein size is expected to have little effect on protein adsorption.</p><p>In order to achieve high surface densities of ethylene oxide (EO) units, we used a sequential double grafting approach whereby the surface was grafted first with poly(2-hydroxyethyl methacrylate) (HEMA) by s-ATRP. OEGMA grafts were then grown from the hydroxyl groups on HEMA chains by a second ATRP. The effect of EO density on protein-resistant properties was then investigated. Protein adsorption on the sequentiallygrafted poly(HEMA)-poly(OEGMA) surfaces (PU/PH/PO) was not only significantly lower than on the unmodified PU as expected, but also much lower than on the PU/PO surfaces with the same poly(OEGMA) chain length. Moreover, protein adsorption decreased with increasing EO density for these grafts. On the PU/PH/PO surface with a poly(OEGMA) chain length of 100, the adsorption of Ls and Fg were reduced by ~98% and >99%, respectively, compared to the unmodified PU. Binary protein adsorption experiments showed that suppression of protein adsorption on the PU/PH/PO surfaces was essentially independent of protein size. The double-grafted OEG layers resisted both proteins equally.</p><p>The general applicability of this approach which combines oxygen plasma treatment and ATRP grafting was also studied. Various kinds of polymers such as PU, silicone hydrogel, and polydimethylsiloxane (PDMS) were chosen as substrates. Poly(MPC) grafts with different chain lengths were achieved by the three-step ATRPgrafting procedure. It was found that protein adsorption levels on the poly(MPC) grafts were significantly lower than on the respective unmodified surfaces. Protein adsorption decreased with increasing poly(MPC) chain length. Among the surfaces investigated, PU/MPC showed the highest protein resistance for a given chain length.</p> / Thesis / Doctor of Philosophy (PhD)

No description available.

<p> Over the past decade, the development of surface-initiated living polymerization methods has brought a breakthrough to surface modification owing to their control ability. Surface-initiated atom transfer radical polymerization (si-ATRP), as the most popular one, has been widely employed to give novel polymer structures and functionalities to various surfaces for the purposes of tailoring surface properties, introducing new functions, or preparing so-called "smart surfaces", which can respond to external stimuli such as solvent type, pH, temperature, electric and magnetic fields etc. In this thesis, the mechanistic study of the si-ATRP was first carried out through modeling to gain good understanding of si-ATRP. Si-ATRP was then employed to prepare different types of polymer brushes to produce "smart surfaces". </p> <p> The kinetic model was developed using the method of moment. Combined with experimental data, a quantitative analysis was carried out for the si-ATRP mechanism. All information of grafted polymer chains, including active chain concentration, radical concentration, chain length, polydispersity, was illustrated. A new radical termination mechanism, termed as migration-termination, was proposed for si-ATRP. </p> <p> Si-ATRP was then employed to graft poly(oligo(ethylene glycol) methacrylate) (POEGMA) block poly(methyl methacrylate) (PMMA) brushes on silicon wafer surfaces. Simple solvent treatment gave nanoscale patterns via the phase segregation of POEGMA and PMMA segments. Various patterns including spherical aggregates, wormlike aggregates, stripe patterns, perforated layers and complete overlayers, were obtained by adjusting the upper block layer thickness. Furthermore, these nanopatterns had a unique stimuli-responsive property, i.e., switching between different morphologies reversibly after being treated with selective solvents. </p> <p> POEGMA-block-poly(2-(methacryloyloxy)ethyl trimethylammonium chloride) (PMETAC) brushes, having two hydrophilic segments, were synthesized by si-ATRP method. A variety of nanopatterns and their stimuli-responsive ability were observed. The adsorption behaviors of fibrinogen on these patterns were thoroughly studied by ellipsometry, water contact angel measurement, AFM and radio labelling method. </p> <p> A novel thermo-responsive copolymer, poly(2-(2-methoxyethoxy)ethyl methacrylate -co-oligo(ethylene glycol) methacrylate) (P(ME02MA-co-OEGMA)), was also grafted onto silicon wafers. Its thermo-responsive behavior and chain conformation in aqueous solution were studied by neutron reflectometry (NR). Both extended and collapsed brushes exhibited good protein adsorption resistance. </p> / Thesis / Doctor of Philosophy (PhD)