This dissertation focuses on the use of subcarrier multiplexing (SCM) in multimode fibers, utilizing carrier frequencies above what is generally utilized for multimode fiber transmission, to achieve high bit rates. In the high frequency region (i.e., frequencies larger than the intermodal bandwidth), the magnitude response of multimode fiber does not decrease monotonically as a function of the frequency but is shown to become relatively flat (but with several deep nulls) with an amplitude below that at DC. The statistical properties of this frequency response at high frequencies are analyzed. The probability density function of the magnitude response at high frequencies is found to be a Rayleigh density function. The average amplitude in this high frequency region does not depend on the frequency but depends on the number of modes supported by the fiber. To transmit a high bit rate signal over the multimode fiber, subcarrier multiplexing is adopted. The performance of the SCM multimode fiber system is presented. The performance of the SCM system is significantly degraded if there are some subcarriers located at the deep nulls of the fiber. Equalization and spread spectrum techniques are investigated but are shown to be not effective in combating the effects of these nulls. To cancel the effects of these deep nulls, training process and diversity coding are considered. The basic theory of diversity coding is given. It is found that the performances of the system with training process and the system with diversity coding are almost identical. However, diversity coding is more appropriate since it requires less system complexity. Finally, the practical limits and capacity of the SCM multimode fiber system are investigated. It is shown that a signal with a bit rate of 1.45 Gbps can be transmitted over a distance up to 5 km. / Ph. D.

Pressure measurements are required in various industrial applications, including extremely harsh environments such as turbine engines, power plants and material-processing systems. Conventional sensors are often difficult to apply due to the high temperatures, highly corrosive agents or electromagnetic interference (EMI) noise that may be present in those environments. Fiber optic pressure sensors have been developed for years and proved themselves successfully in such harsh environments. Especially, diaphragm based fiber optic pressure sensors have been shown to possess advantages of high sensitivity, wide bandwidth, high operation temperature, immunity to EMI, lightweight and long life. Static and dynamic pressure measurements at various locations of a gas turbine engine are highly desirable to improve its operation and reliability. However, the operating environment, in which temperatures may exceed 600 °C and pressures may reach 100 psi (690 kPa) with about 1 psi (6.9kPa) variation, is a great challenge to currently available sensors. To meet these requirements, a novel type of fiber optic engine pressure sensor has been developed. This pressure sensor functions as a diaphragm based extrinsic Fabry-Pérot interferometric sensor. One of the unique features of this sensor is the all silica structure, allowing a much higher operating temperature to be achieved with an extremely low temperature dependence. In addition, the flexible nature of the sensor design such as wide sensitivity selection, and passive or adaptive temperature compensation, makes the sensor suitable for a variety of applications An automatically controlled CO₂ laser-based sensor fabrication system was developed and implemented. Several novel bonding methods were proposed and investigated to improve the sensor mechanical ruggedness and reduce its temperature dependence. An engine sensor testing system was designed and instrumented. The system generates known static and dynamic pressures in a temperature-controlled environment, which was used to calibrate the sensor. Several sensor signal demodulation schemes were used for different testing purposes including a white-light interferometry system, a tunable laser based component test system (CTS), and a self-calibrated interferometric-intensity based (SCIIB) system. All of these sensor systems are immune to light source power fluctuations, which offer high reliability and stability. The fiber optic pressure sensor was tested in a F-109 turbofan engine. The testing results prove the sensor performance and the packaging ruggedization. Preliminary laboratory and field test results have shown great potential to meet not only the needs for reliable and precise pressure measurement of turbine engines but also for any other pressure measurements especially requiring high bandwidth and high temperature capability. / Ph. D.

The use of optical fiber sensors is increasing widely in civil, industrial, and military applications mainly due to their, (a) miniature size, (b) high sensitivity, (c) immunity from electro-magnetic interference, (d) resistance to harsh environments, (e) remote signal processing ability, and, (f) multiplexing capabilities. Because of these advantages a variety of optical fiber sensing techniques have evolved over the years having potentials for myriad of applications. One very challenging job, for any of these optical fiber sensing techniques, is to implement a stand alone system with the design and development of all the signal processing models along with the necessary hardware, firmware, and software satisfying the real-time signal processing requirements. In this work we first develop the equations for the system model of the wavelength modulated extrinsic Fabry-Perot interferometric (EFPI) optical fiber sensor, and then design and build all the hardware and software necessary to implement a stand-a / Ph. D.

Structural health monitoring (SHM) has become a strong national interest because of the need of reliable and accurate damage detection methods for aerospace, civil and mechanical engineering infrastructure. Health monitoring of these structures usually requires the sensors to have such features as large area coverage, maintenance free or minimum maintenance, ultra-low cost per measurement point, and capability of operation in harsh environments. Fiber Bragg grating (FBG) has attracted considerable interest for this application because of its compactness, electromagnetic immunity, and excellent multiplexing capability. Several FBG multiplexing techniques have been developed to increase the multiplexing number and further reduce the unit cost. To the author's best knowledge, the current demonstrated maximum multiplexing number are 800 FBG sensors in a single array using optical frequency domain reflectometry (OFDR), whose maximum fiber span is limited by the coherence length of light source. In this work, we proposed and demonstrated a wavelength-scanning time-division multiplexing (WSTDM) of 1000 ultra-weak FBGs for distributed temperature sensing. In comparison with the OFDR method, the WSTDM method distinguishes the sensors by different time delays, and its maximum operation distance, which is limited by the transmission loss of the fiber, can be as high as tens of kilometers. The strong multiplexing capability and low crosstalk of the ultra-weak FBG sensors was investigated through both theoretical analysis and experiment. An automated FBG fabrication system was developed for fast FBG fabrication. With this WSTDM method, we multiplexed 1000 ultra-weak FBGs for distributed temperature sensing. Besides the demonstrated temperature measurement, the reported method can also be applied to measure other parameters, such as strain, pressure. / Ph. D.

This research provides the first known procedure for cleanly and consistently reducing the diameter of single-crystal sapphire optical fiber (SCSF) below the limits of standard production methods, including the first production of subwavelength-diameter optical fiber (SDF) composed of single-crystal sapphire. The first known demonstration of an air-clad single crystal sapphire optical fiber demonstrating single-mode behavior is also presented, and the single-mode cutoff wavelength and diameter are determined. Theoretical models describing and predicting the optical behavior of low modal volume sapphire optical fibers are also presented. These models are built upon standard weakly-guiding optical fiber theory, which is found to be accurate once experimentally-determined properties of the SCSF are substituted for theoretical values. Reduced modal dispersion is also observed in the form of decreased laser pulse broadening in reduced-diameter SCSF. The improvements in spatial resolution for distributed sensing systems such as Raman distributed temperature sensing are also predicted based on the measured decrease in pulse duration. This research also provides an enhanced understanding of the etching behavior of sulfuric and phosphoric acids on sapphire surfaces, including the first reporting of etching rates and activation energies for a-plane sapphire surfaces. Morphological changes of sulfuric and phosphoric acids at and beyond the temperature ranges used in etching were also tested and discussed in detail, especially regarding their practical impact on observed etching behavior. The demonstration of LMV single-crystal sapphire optical fibers enables the adaptation of numerous sensing schemes requiring low modal volume or single-mode behavior to be utilized in extreme environments. / Ph. D.

The power industry relies on high voltage transformers as the backbone of power distribution networks. High voltage transformers are designed to handle immense electrical loads in hostile environments. Long term placement is desired, however by being under constant heavy load transformers face mechanical, thermal, and electrical stresses which lead to failures of the protection systems in place. The service life of a transformer is often limited by the life time of its insulation system. Insulation failures most often develop from thermal faults, or hotspots, and electrical faults, or partial discharges. Detecting hotspots and partial discharges to predict transformer life times is imperative and much research is focused towards these topics. As these protection systems fail they often generate gas or acoustic signals signifying a problem. Research has already been performed discovering new ways integrate optical fiber sensors into high voltage transformers. This thesis is a continuation of that research by attempting to improve sensor sensitivity for hydrogen and acetylene gasses. Of note is the fabrication of new hydrogen sensing fiber for operation around a larger absorption peak and also the improvement of the acetylene sensor's light source stability. Also detailed is the manufacturing of a field testable prototype and the non-sensitivity testing of several other gasses. The developed sensors are capable but still could be improved with the use of more powerful and stable light sources. / Master of Science

Several techniques for measuring humidity are presented. The goal of the study is to use the electrostatic self-assembled monolayer synthesis process to fabricate a Fabry-Parot Cavity based optical fiber humidity sensor. The sensing scheme bases on the refractive index change with relative humidity of the film applied to the end of optical fiber. That is, the change in reflected optical power indicates certain humidity. To achieve this, some chemicals induce on specific coating materials were applied at the end of optical fiber. In this thesis, experimental results are given to prove that the humidity sensor has high sensitive and fast response time. Furthermore, we investigate the potential for the use of human breathing monitoring and air flow rate detection. Results from preliminary tests of each are given. / Master of Science

The use of optical fiber sensors is increasing widely in industry, civil, medicine, defense and research. Among different categories of these sensors is the Extrinsic Fabry-Perot interferometer (EFPI) sensor which is inherently simple and requires only modest amount of interface electronics. These advantages make it suitable for many practical applications. Investigating a cost-effective, reliable and repeatable method for optical fiber sensor fabrication is challenging work. In this thesis, a system for controlled fabrication of Fabry-Perot optical fiber sensors is developed and presented as the first attempt for the long-term goal of automated EFPI sensor fabrication. The sensor fabrication control system presented here implements a real-time control of a carbon dioxide (CO₂) laser as sensor bonding power, an optical fiber white light interferometric subsystem for real-time monitoring and measurement of the air gap separation in the Fabry-Perot sensor probe, and real-time control of a piezoelectric (PZT) motion subsystem for sensor alignment. The design of optoelectronic hardware and computer software is included. A large number of sensors are fabricated using this system and are tested under high temperature and high pressure. This system as a prototype system shows the potential in automated sensor fabrication. / Master of Science

Due to their compact size, sensitivity, and ability to be multiplexed, intrinsic Fabry-Perot interferometers (IFPIs) are excellent candidates for almost any multi-point temperature or strain application, and it is well-known that using a single-mode lead-in fiber, a multi-mode fiber section as the Fabry-Perot cavity, and an additional single-mode fiber as the tail results in a structure that generates strong interference fringes while remaining robust. Though the basic principles behind these sensors are understood, to the best of the author's knowledge there hasn't been a thorough investigation into the design and fabrication of a chain of multiplexed IFPI sensors for industrial use in an environment where serious issues associated with the size of the test coupon, sensor placement, and mechanical reinforcement of the fiber could arise. This thesis details the preparation and results of this investigation. It turns out that fabricating a sensor chain with appropriate sensor spacing and excellent temperature response characteristics proved a significant challenge, and issues addressed include inter-sensor interference, high-temperature mechanical reinforcement for bare fiber sections, and high bending losses. After overcoming these problems, a final sensor chain was fabricated and characterized. This chain was then subjected to a battery of tests at the National Energy Technology Laboratory (NETL), where four multiplexed sensors were installed on a 2â x2â coupon in a simulated gas turbine environment. Final results are presented and analyzed. The work that went into developing this chain lays the foundation for future efforts in developing quasi-distributed temperature sensors by identifying potential obstacles and fundamental limitations for certain approaches. / Master of Science

An optical fiber has been developed that can be used as a chemical gas sensor. Fabrication of the optical fiber produces a fiber that has a solid core with a porous cladding. The porous cladding region is made from a spinodally phase separable glass where the secondary phase is removed through dilute acid leaching. A non-phase separable glass composition is used for the core region. The properties of the phase separable glass are dependent on the processing conditions and the thermal history of the glass after the porosity has been achieved. Investigation of how processing conditions affected the pore structure was conducted to determine what pore characteristics are achievable for the glass composition used. Phase separation temperature, removal of silica gel deposited in the pores, and the post fabrication heat treating were used as experimental processing conditions. A maximum useable average pore size of approximately 29 nm was achieved. Maximum pore volume in the experimental groups was 0.4399 cc/g. Most heat treatments of the porous glass caused consolidation of the pore structure, with some conditions producing pore coarsening. / Master of Science