>Magister Scientiae - MSc / Separation between the South American and African plate’s occurred along the present day Atlantic margin during the Middle to Late Jurassic leading to the formation of a passive margin along the west coast of Southern Africa. The margin then later developed into the large Orange Basin flanking the west coasts of South Africa and Namibia. The Orange Basin on the west coast of South Africa covers an area of roughly 130 000 square kilometers relevant to the 200 m isobath and has roughly one well drilled for every 4000 square kilometers. The basin has proven hydrocarbon reserves and potential for further discoveries. The study area is located within South African exploration licencing blocks 3A/4A and 3B/4B and covers a region of roughly 97 km by 150 km. The study aims at understanding the geological processes responsible for the formation of the Orange Basin with a focus on the evolution of source rock maturity. The methodology involved utilizing the Petrel software for seismic interpretation and well correlation utilising twodimensional seismic data and all the relevant well data including geological well logs, petrophysical well logs, well top data, check-shot data, borehole temperature data and geochemical well data such as Rock Eval and vitrinite reflectance data. PetroMod (IES, Version 10) was utilized to simulate the Orange Basin evolution and the affect on source rock maturity. Seismic interpretation of the Post-Hauterivian succession shows a relative thickening of the sedimentary sequence westward as the basin evolves from the early drift to complete drift phase. Results from the petroleum system modeling indicate that the Barremian - Early Aptian source rock is at present overmature and producing mostly gas in the shelf areas whereas the potential for oil are most likely present in the deep water area of the basin where Tertiary progradation has resulted in renewed petroleum generation. Petroleum system modeling results indicate that the younger Cenomanian - Turonian source rock is less mature than the older Barremian - Early Aptian source rock as indicated by a lower transformation ratio and is mainly producing oil.

>Magister Scientiae - MSc / This study investigates the viability of the sedimentary deposits in the Northern Orange basin for carbon storage and sequestration. A combination of geological modelling, petrographic and geochemical techniques are used to investigate this scenario after an initial seismic-well tie had been performed to match the formation tops in Well AF-1 with the 3D seismic volume acquired in this basin in 2009. Core description of well AF-1 assisted in identifying different facies and samples taken at specific depths for petrographic and geochemical analyses, while different geological formations were mapped from the calibrated positions of seismic-well tie throughout the seismic volume. The well data and geophysical logs were utilized to generate petrophysical properties and used to calibrate observations made from seismic interpretations. The facies log used in this study was generated using the Python’s script on Petrel 2014 Gamma Ray, while the density log was used to generate the porosity log. The generated facies and porosity logs were upscaled and used to populate a 3D grid using faults and surfaces identified in the seismic volume. The sedimentological properties of the subsurface were identified utilizing petrographic descriptions including measurements of sorting, colour and grain sizes. While the mineralogical properties of the record was verified through XRD analyses and thin section. The facies and porosity modelling revealed the dominance of siltstones and sandstones as the main sedimentary facies throughout the sequence. Sandstones are extensive and prominent within the Cenozoic and Mastrichtian, while the unit dated to the Barremian is identified as having the best potential for CO2 storage based on the overlaying capping unit. Quartz, Plagioclase feldspar (Albite), Biotite and Kaolinite are the major minerals identified in all four samples. Each of these minerals has an implication for which may influence the long term storage of CO2 with the potential to form as they may form part of the inra-porous post-depositional cementation and hence change the porosity and permeability properties. The presence of Albite as observed on the XRD may predict possible mineralisation of CO2 to form Dawsonite when reservoir is injected with CO2. The Barremian sandstone which straddles the Aptian shale at the top and the Hauterivian Shale and Siltsone deposit at the bottom holds a good promise for a potential CO2 storage. An estimated volume of CO2 that could be stored in the reservoir of the Barremian sandstone in zone 8 is limited to the lateral seal of shale above the reservoir in zone 7 of the Aptian age. The method used to determine the potential storage capacity of CO2 was performed by Alexandros Tasianas and Nikolaos Koukouzas (2016). The Equation used to determine CO2 storage capacity is: mCO2 = RV * Ø * Sg * δ(CO2) . / 2021-09-01

Masters of Science / Petrophysical evaluation of four wells within Cretaceous gas-bearing sandstone reservoirs in blocks 4 and 5 Orange Basin, South Africa. Thierry Kamgang The present research work evaluates the petrophysical characteristics of the Cretaceous gasbearing sandstone units within Blocks 4 and 5 offshore South Africa. Data used to carry out this study include: wireline logs (LAS format), base maps, well completion reports, petrography reports, conventional core analysis report and tabulated interpretative age reports from four wells (O-A1, A-N1, P-A1 and P-F1). The zones of interest range between 1410.0m-4100.3m depending on the position of the wells. The research work is carried out in two phases: The first phase corresponds to the interpretation of reservoir lithologies based on wireline logs. This consists of evaluating the type of rocks (clean or tight sandstones) forming the reservoir intervals and their distribution in order to quantify gross zones, by relating the behavior of wireline logs signature based on horizontal routine. Extensively, a vertical routine is used to estimate their distribution by correlating the gamma-ray logs of the corresponding wells, but also to identify their depositional environments (shallow to deep marine).Sedlog software is used to digitize the results. The second phase is conducted with the help of Interactive Petrophysics (version 4) software, and results to the evaluation of eight petrophysical parameters range as follow: effective porosity (4.3% - 25.4%), bulk volume of water (2.7% – 31.8%), irreducible water saturation (0.2%-8.8%), hydrocarbon saturation (9.9% - 43.9%), predicted permeability (0.09mD – 1.60mD), volume of shale (8.4% - 33.6%), porosity (5.5% - 26.2%) and water saturation (56.1% - ii 90.1%). Three predefined petrophysical properties (volume of shale, porosity and water saturation)are used for reservoir characterization. The volume of shale is estimated in all the wells using corrected Steiber method. The porosity is determined from the density logs using the appropriate equations in wells O-A1 and P-A1, while sonic model is applied in well A-N1 and neutron-density relationship in well P-F1. Formation water resistivity (Rw) is determined through the following equation: Rw = (Rmf × Rt) / Rxo, and water saturation is calculated based on Simandoux relation. Furthermore, a predicted permeability function is obtained from the crossplot of core porosity against core permeability, and it results match best with the core permeability of well O-A1. This equation is used to predict the permeability in the other wells. The results obtained reveal that average volumes of shale decrease from the west of the field towards the east; while average porosities and water saturations increase from the south-west through the east despite the decreasing average water saturation in well P-A1. A corroboration of reference physical properties selected for reservoir characterization, with predefined cut-off values result to no net pay zones identified within the reservoir intervals studied. Consequently, it is suggested that further exploration prospects should be done between well O-A1 and A-N1.

>Magister Scientiae - MSc / The reservoir quality of the Orange Basin, offshore South Africa is known to be immensely impaired by the presence of authigenic minerals. The collective effects of burial, bioturbation, compaction and chemical reactions between rocks, fluid and organic matter conclusively determined the quality of reservoirs within the Orange basin. The aim of this study was to provide information on the quality of reservoirs within the Orange Basin. Data used to conduct this study include wireline logs (LAS format), well completion reports and core samples from potential reservoir zones of wells K-A2, K-A3 and K-E1. To accomplish the aim, petrophysical parameters were calculated, such as porosity, permeability and water saturation. Besides, depositional environments were identified using gamma ray log and core logging techniques. Thirdly, petrographic studies were supporting techniques in understanding how various minerals and diagenetic processes play a role in reservoir characterisation. Geophysical wireline logs (Gamma ray, Resistivity, Bulk density and Caliper) allowed for the estimation of the three main reservoir properties; namely: porosity, water saturation and permeability. The porosity calculations revealed a range of 3-18% for well K-A2, 2%-13% for well K-A3 and 3%-16% for well K-E1. The permeability’s ranged from 0.08-0.1 mD and 0.001-1.30 mD for K-A3 and K-E1, respectively. Thus, the findings of the petrophysical evaluation of the wells in Interactive Petrophysics indicated that the reservoir intervals of wells K-A2, K-A3 and K-E1 are of poor to good quality. Based on the core analyses, the depositional environment is mostly shallow marine, specifically tide dominated for well K-A2, sandstone channel for well K-A3 and intertidal environment for well K-E1. These environments were confirmed by XRD, revealing glauconite as the prominent mineral.

>Magister Scientiae - MSc / Clay diagenesis phenomenon and their effects on some petrophysical properties of lower cretaceous silliciclastic sandstones, offshore Orange basin have been established. Previous studies on Orange basin revealed that chlorite and quartz cements have significantly compromised the reservoir quality in this basin but it is expected that the reservoirs shows better improvement basinward, an analogy of this is displayed by tertiary sandstones deposit, offshore Angola. The main goal of this thesis is to perform reservoir quality evaluation by intergrating geological, geochemical and geophysical tools to substantiate the effects of clay minerals distribution and its subsequent diagenesis on the intrinsic properties (porosity, permeability and saturation) of reservoir intervals encountered within three wells in block 3A (deeper waters), offshore Orange basin. Five lithofacies were identified based on detailed core description from wells KF-1, KH-1 and AU-1 in this block. The facies were grouped based on colour and grain sizes, they are named : A1 (shale), A2 (sandstone), A3 (siltstone), A4 (dark coloured sandstone) and A5 (conglomerates).Depositional environment is predominantly marine, specifically, marine delta front detached bars and deepwater turbiditic sandstone deposit. Geophysical wire line logs of gamma ray, resistivity logs combo and porosity logs were interpreted, parameters and properties such as VCL, porosity, permeability and saturation were estimated from these logs and the values obtained were compared with values from conventional core analysis data, the values agreed well with each other. Detailed petrographic studies (SEM, XRD and thinsection) plus geochemical studies (CEC, EDS, pH, Ec) were carried out on twenty two core samples to establish if these clay minerals and other cements have pervasive effects on the reservoir quality or otherwise.

>Magister Scientiae - MSc / The evaluation of petroleum reservoirs has shifted from single approach to an integrated approach. The integration, analysis and understanding of all available data from the well bore and creating property models is an exceptional way to characterize a reservoir. Formulating, implementing, and demonstrating the applicability of the joint inversion of seismic and well-bore related observations, and the use of information about the relationship between porosity and permeability as the key parameters for identifying the rock types and reservoir characterization is a vital approach in this study. Correlating well and seismic data, potential reservoirs can be delineated and important horizons (markers) can be pointed out to better characterize the reservoir. This thesis aims to evaluate the potential petroleum reservoirs of the Wells K-A1, K-A2, K-A3 and K-H1 of the Shungu Shungu field in the Orange Basin through the integration and comparison of results from core analysis, wireline logs and seismic and attempt to produce a good reservoir model and by additionally utilizing Petrophysics and seismic and trying to better understand why the area has dry wells. Different rock types that comprise reservoir and non reservoirs are identified in the study and five Facie types are distinguished. Tight, fine grained sandstones with low porosity values ranging from 3% - 6% where dominant in the targeted sandstone layers. Porosity values ranging from 11% - 18% where identified in the massive sandstone lithologies which where hosted by Well’s K-A2 and K-A3. Low permeability values reaching 0.1mD exist throughout the study area. Areas with high porosity also host high water saturation values ranging from 70 – 84%. An improvement in the porosity values at deeper zones (3700m -3725m) and is apparent. Poroperm plots exhibit quartz cemented sandstones and density with neutron plot suggest that the sandstones in the area contain quarts and dolomite mineralization.Well K-A3, consist of a cluster by quartzitic sandstone, meaning there is a large amount of sandstone present. There are apparent high porosity values around the sandstone. What is apparent from this plot is that there are many clusters that are scattered outside the chart. This could suggest some gas expulsions within this Well. Sandstones within the 14B2t1 to 14At1 interval are less developed in the vicinity covered by well K-A2 than at the K-A1 well location. The main targeted sandstones belong to the lower cretaceous and lie just below 13At1. The four wells drilled in this area are dry wells. The areas/blocks surrounding this area have shown to possess encouraging gas shows and a comparative study could reveal better answers. At deeper zones of the well at an interval of 5350m -5750m, there are more developed sandstones with good porosity values. The volume of shale is low and so is the water saturation. The main target sandstones in the study area are the Lower Cretaceous sandstones which are at an interval 13At1. These sandstones are not well developed but from the property model of the target surface it can be seen that the porosity values are much more improved than the average values applied on all the zones on the 3D grid.

>Magister Scientiae - MSc / The Orange Basin provides exceptional 3-D structures of folds and faults generated during soft-sediment slumping and deformation which is progressive in nature. 3-D seismic and structural evaluation techniques have been used to understand the geometric architecture of the gravity collapse structures. The location of the seismic surveyed area is approximately 370 km northwest of the Port of Saldanha. The interpretation of gravitational tectonics indicate significant amount of deformation that is not accounted for in the imaged thrust belt structure. The Study area covers 8200 square kilometre (km²) of the total 130 000 km² area of the Orange Basin offshore South Africa. The south parts of the Study area are largely featureless towards the shelf area. The north has chaotic seismic facies as the result of an increase in thrust faults in seismic facies 2. Episodic gravitational collapse system of the Orange Basin margin characterizes the late Cretaceous post-rift evolution. This Study area shows that implications of stress field and thrust faulting to the thickness change by gravity collapse systems are not only the result of geological processes such as rapid sedimentation, margin uplift and subsidence, but also could have occurred as the result of the possible meteorite impact. These processes caused gravitational potential energy contrast and created gravity collapse features that are observed between 3000-4500ms TWT intervals in the seismic data. / Shell Exploration & Production Company

<p>The Orange Basin was formed during the late Jurassic to early Cretaceous periods due to Gondwana breakup and rifting and later drifting apart of the African and South American plates. The basin consists of siliciclastic sandstone which took its sediment supply from river system with a rivalling delta to the north of the basin. Geological and petrophysical studies were carried out to evaluate the reservoir potential of the wells in the study area. This study considered five wells (A-G1, A-W1, A-K1, A-K2 and A-Y1) in the Orange Basin with attention to the Albian age sandstone. Only three of the studied wells (A-G1, A-W1 and A-K1) have core samples for analysis. The methods used for the execution of this study include the description and calibration of spot cores with conventional standard logging record responses, wireline log interpretation using sequence stratigraphy approach, detailed petrographic (SEM, HR-TEM, XRD and thin section) and geochemical (pore water geochemistry, FTIR and XRF) analyses, and petrophysical analysis to unravel the complexities with regard to facies association, depositional environment and diagenesis. Linking diagenesis to depositional facies and sequence stratigraphy has given a clearer picture to the spatial and temporal distribution of diagenetic alterations and thus of evolution of reservoir quality in the studied wells. Three depositional lithofacies were identified based on a detailed core description [fine grained sandstone (F1), very fine grained sandstone (F2) and mudstone (F3)]. Fluvio-deltaic and shallow marine environments were also interpreted from the core description based on the sedimentary structures and mineral assemblage while the log interpretation shows that the different reservoir units range between LST, TST and HST but mostly of LST. Mineralogical predictions were made possible in the wells without core samples (A-K2 and A-Y1) through the use of density-neutron cross plot, these reveal that the two wells contain some considerable amount of clay minerals like kaolinite, chlorite and illite.</p>

<p>The Orange Basin was formed during the late Jurassic to early Cretaceous periods due to Gondwana breakup and rifting and later drifting apart of the African and South American plates. The basin consists of siliciclastic sandstone which took its sediment supply from river system with a rivalling delta to the north of the basin. Geological and petrophysical studies were carried out to evaluate the reservoir potential of the wells in the study area. This study considered five wells (A-G1, A-W1, A-K1, A-K2 and A-Y1) in the Orange Basin with attention to the Albian age sandstone. Only three of the studied wells (A-G1, A-W1 and A-K1) have core samples for analysis. The methods used for the execution of this study include the description and calibration of spot cores with conventional standard logging record responses, wireline log interpretation using sequence stratigraphy approach, detailed petrographic (SEM, HR-TEM, XRD and thin section) and geochemical (pore water geochemistry, FTIR and XRF) analyses, and petrophysical analysis to unravel the complexities with regard to facies association, depositional environment and diagenesis. Linking diagenesis to depositional facies and sequence stratigraphy has given a clearer picture to the spatial and temporal distribution of diagenetic alterations and thus of evolution of reservoir quality in the studied wells. Three depositional lithofacies were identified based on a detailed core description [fine grained sandstone (F1), very fine grained sandstone (F2) and mudstone (F3)]. Fluvio-deltaic and shallow marine environments were also interpreted from the core description based on the sedimentary structures and mineral assemblage while the log interpretation shows that the different reservoir units range between LST, TST and HST but mostly of LST. Mineralogical predictions were made possible in the wells without core samples (A-K2 and A-Y1) through the use of density-neutron cross plot, these reveal that the two wells contain some considerable amount of clay minerals like kaolinite, chlorite and illite.</p>

Magister Scientiae - MSc (Earth Science) / The Orange basin is relatively underexplored with 1 well per every 4000km2 with only the Ububhesi gas field discovery. Block 1 is largely underexplored with only 3 wells drilled in the entire block and only well A?F1 inside the 1500km2 3?D seismic data cube, acquired in 2009. This study is a reservoir characterization of well A?F1, utilising the acquired 3?D seismic data and re?analysing and up scaling the well logs to create a static model to display petrophysical properties essential for reservoir characterization. For horizon 14Ht1, four reservoir zones were identified, petro?physically characterized and modelled using the up scaled logs. The overall reservoir displayed average volume of shale at 24%, good porosity values between 9.8% to 15.3% and permeability between 2.3mD to 9.5mD. However, high water saturation overall which exceeds 50% as per the water saturation model, results in water saturated sandstones with minor hydrocarbon shows and an uneconomical reservoir.