This thesis deals with the high speed transient modelling in the electrical networks. The introduction of this work discusses mathematical models of the individual devices used in the system and focuses on the line representation. It also contains a more detailed description of Bergeron and frequency dependent line model. The objective of this thesis is to design a network model using ATP-EMTP simulation program. In this model, the switching overvoltage caused by shunt reactor switching and lightning overvoltage are simulated. The thesis thoroughly describes the settings of the components used in the model of analysed network and in conclusion evaluates obtained simulation results in a relation to the insulation coordination.

The Swedish Energy Agency has a target to increase solar photovoltaics (PV) power production by up to 5-10% of the total electricity demand by the year 2040. The PV potential for the residential market is high and its contribution to the total installed PV capacity is expected to increase significantly. The technical requirements should be met to keep high reliability and good power quality at the customers, therefore, it is important for planning reasons to proactively find the maximum amount PV power that can be connected at each low-voltage network without violating the performance of the grid. This amount is known as the hosting capacity. A method for PV hosting capacity estimation by taking overvoltage and transformer overload as performance indices was developed in this thesis. The method does not require any knowledge about the topology of the network. The overload hosting capacity can be estimated for any combination of customers having PV power and for the overvoltage hosting, the minimum at each penetration level can be estimated. The method was implemented on four low-voltage networks located in a typical Vattenfall medium-voltage network and the comparison of the estimation results to a power flow simulation showed good correspondence. It was shown how the impact of PV power in adjacent secondary substations can be accounted for. Using SS-EN50160 voltage limits, the studied networks were able to handle 3-7 times the PV penetration level needed (8 kWp at 20% of the customers) to achieve the national goal in Sweden without grid investments.

An electrical bushing is one of the most important elements in a power transformer. Steep front surges such as transient impulse voltage from lightning strikes is an inevitable electromagnetic transient mostly happening in power transmission and distribution system. The bushing might lead to be degraded due to such kind of surge. This project deals with overvoltage stress distribution on the transformer bushing under the effect of electromagnetic transient response such as lightning impulse.  To understand the behavior of transient response on the bushing, a proper model of power transformer bushing is built-in Comsol multiphysics to authenticate the stress distribution. The electromagnetic wave of impulse propagates onto the overhead line that connects with the transformer. Some understanding of the transient behavior of a conductor bushing has been achieved through studying the influence of inductance property and the skin effect characteristics of a multi-layer coaxial cable on the wave propagation, which has been structured in this project to simplify the model. On the other hand, the skin effect analysis on the conductor of the bushing has been taken also into account in this project using real conductor simulation in the Comsol model. Thus, it will be interesting to compare the real conductor model with the perfect conductor of the bushing through analyzing the current density effect on it.  In this project, multi-layer of coaxial cable and transformer bushing are simulated. The simulation is carried out for time domain and frequency domain in Comsol based on the model characteristics. / En elektrisk genomföring är ett av de viktigaste elementen i en transformator. Spänningsvågor med branta fronter som impulsspänningar från blixtnedslag är ett oundvikligt elektromagnetiskt övergående fenomen som oftast sker i kraftöverförings- och distributionssystem. Genomföringen kan leda till att degraderas på grund av en sådan våg. Detta projekt handlar om fördelning av överspännings på transformatorgenomföringen under påverkan av elektromagnetisk transient respons, såsom blixtimpuls.  För att förstå beteendet hos övergående respons på genomföringen är en korrekt modell av transformatorgenomföring inbyggd Comsol-flerfysik för att autentisera spänningsfördelningen. Den elektromagnetiska impulsvågen fortplantas från luftledningen som ansluter till transformatorn. Viss förståelse för det övergående beteendet hos en ledargenomföring har uppnåtts genom att studera påverkan av induktansegenskaper och hudeffektegenskaperna hos en flerskikts koaxialkabel på vågutbredningen, vilket har strukturerats i detta projekt för att förenkla modellen. Å andra sidan har hudeffektanalysen på genomföringens ledare beaktats i detta projekt med användning av verklig ledarsimulering i Comsol-modellen. Således blir det intressant att jämföra den riktiga ledarmodellen med den perfekta ledaren för genomföringen genom att analysera strömtäthetseffekten på den.  I detta projekt simuleras flerskikt av koaxialkabel och transformatorgenomföring. Simuleringen utförs för tidsdomän och frekvensdomän i Comsol baserat på modellegenskaperna.

Orientador: André Nunes de Souza / Banca: Ivan Nunes da Silva / Banca: Luiz Gonzaga Campos Porto / Resumo: O presente trabalho visa o desenvolvimento de uma ferramenta computacional confiável na análise e estimação dos níveis de tensões induzidas em linhas de distribuição. Neste contexto, utilizam-se ferramentas computacionais consolidadas, como o ATP (Alternative Transients Program), que combinado a um software desenvolvido em Visual Basic, permitem quantificar e avaliar o nível de sobretensões nas linhas de distribuição. Por meio de modificações nas técnicas clássicas de modelagem das descargas atmosféricas, foi possível a construção de um software em Visual Basic capaz de quantificar os valores das tensões induzidas em linhas de distribuição finitas. A avaliação dos níveis de sobretensões induzidas nas mesmas foi implementada pela associação deste software a um programa de simulação (ATP), a fim de se obter resultados fidedignos deste transitório. Tais resultados foram utilizados para se avaliar o desempenho das... (Resumo completo, clicar acesso eletrônico abaixo) / Abstract: The present work aims at the development of a trustworthy computacional tool in the analysis and estimate of the levels of induced overvoltage in distribution network. In this context, consolidated computacional tools are used, as ATP (Alternative Transients Program), that combined with a software developed in Visual Basic (beginner's all-purpose symbolic instruction code), they allow to quantify and to evaluate the level of overvoltage in the distribution network. By the means of modifications in the classic techniques of modeling of the atmospheric discharges, the construction of a software in Visual Basic was possible to quantify the values of the induced overvoltage in a finite... (Complete abstract click electronic access below) / Mestre

Conselho Nacional de Desenvolvimento Científico e Tecnológico / A busca por soluções mitigatórias, no que tange aos efeitos das sobretensões transitórias atreladas às manobras de energizações e religamentos das linhas de transmissão, contemplam um tema desafiador e com fortes impactos sobre a coordenação de isolamento dos sistemas elétricos. Muito embora o reconhecimento de propostas clássicas e comerciais para a atenuação destes fenômenos, outras possibilidades, certamente, ainda são meritórias de destaque e investigações. Neste contexto, a presente dissertação encontra-se alicerçada na exposição dos fundamentos físicos e matemáticos de uma estratégia baseada em chaveamentos controlados, cujos instantes para o religamento da linha são pré-programados. A avaliação computacional da eficácia da metodologia é realizada utilizando o simulador ATP, no qual são efetuados estudos em um sistema elétrico típico submetido à curtos-circuitos sucedidos por desligamentos e subsequentes religamentos, sob a ação da tecnologia aqui focada e na ausência da mesma. / The search for mitigation solutions, with respect to the effects of overvoltages linked to the energization and reclosing maneuvers of transmission lines include a challenging subject with strong impact on the insulation coordination of electrical systems. Although the recognition of classical and commercial proposals to mitigate these phenomena, other possibilities are certainly still worthwhile highlighting and investigations. In this context, the present work is grounded in the exposure of the physical and mathematical foundations of a strategy based on controlled switchings, whose moments to the line reclosing are pre-programmed. The computational evaluation of the effectiveness of the methodology is made using the ATP simulator, which are studies in a typical electrical system subjected to the action of short-circuits fallowed by shutdowns and subsequent reclosing, under the action of technology here focused and lack thereof. / Dissertação (Mestrado)

Många elektriska apparater är i behov av reaktiv effekt för att kunna fungera. Transport av reaktiv effekt tar onödig plats av den tillgängliga kapaciteten i elnätet, därför används kondensatorbatterier nära slutanvändaren för att generera reaktiv effekt. Därmed genereras och förbrukas den reaktiva effekten i en avskild del av nätet. Tillkoppling av kondensatorbatterier ger upphov till transienter som kan skada andra närliggande komponenter. Utifrån det verkliga ställverket Stallbacka i Trollhättan har denna rapport analyserat de transienter som uppstår efter tillkoppling av ett kondensatorbatteri inom mellanspänningsområdet. Analysen har innefattat hur stora transienterna blir efter olika förutsättningar och scenarier. Resultatet visade att transienterna i detta fall aldrig nådde upp till några allvarliga nivåer, och därmed klarade komponenterna sig med god marginal. Huruvida transienterna påverkar elkvaliteten är oklart, då det inte finns några definierade krav. Slutligen skulle ett beräkningsverktyg för förutspådda transienter tas fram. Beräkningsverktyget blev aldrig fullständigt på grund av den ohanterliga lösningen som erhölls. / Many electrical devices need reactive power to operate. Transmission of reactive power occupies a proportion of the available capacity in the power system and therefore capacitor banks are used near to the end user to generate reactive power. Thus, the reactive effect is generated and consumed in a separate part of the power system. Capacitor banks switching causes transients which may damage the surrounding components. Based on the real substation Stallbacka in Trollhättan, this study has analysed capacitor banks switching transients within the medium voltage level. The analysis has covered the size of these transients according to different conditions and scenarios. The result showed that the transients in this case never reached serious levels, thus there was no impact on the components. It is not clear whether the transients affect the power quality because there are no defined limits.  A calculation tool to the predicted transients was supposed to be created in the process. This calculation tool was never completed due to the unmanageable solution that was obtained.

The objective of this master's thesis is new power converter design for bicycle with combustion engine and electric power transmission. The power converter is control by microprocessor and control algorithm is designed to achieve maximum efficiently of combustion engine. Converter and servomotor for controlling combustion engine throttle are located in metal box. Hardware, firmware and metal box are designed in the thesis.

The purpose of this thesis is to introduce readers with design of a surge arresters in four different categories. In the first part of this thesis is described theory of overvoltage, surge arresters and testing. The second part of this thesis is focused on design of surge arresters to protect from overvoltage due switching capacitive loads. The thesis continued with design of surge arresters in medium voltage network. The next part is design of surge arresters to protect from overvoltage due switching inductive loads. The next point is protective distance of surge arresters in different lighting overvoltages. In the conclusion of this thesis is the appreciation of whole problems about surge arresters.

Demand for electrical power is increasing everyday. Along with the increase in power demand, the characteristics of the loads are also changing. From being high power consuming, simple, robust loads, today loads are more efficient, but at the same time more sensitive. The performance and life of these highly sensitive loads depend a lot on the quality of power supplied to them. <p>Power quality is any deviation of the voltage or current waveform from its normal sinusoidal waveshape. These disturbances include, but are not limited to, sag, undervoltage, interruption, swell, overvoltage, transients, harmonics, voltage flicker and any other distortions to the sinusoidal waveform. Occurrence of one or more of such disturbances is called a power quality event. Automatic classification of these disturbances is important for quick determination of the causes and to characterize possible impacts of the disturbances.<p>Modern microprocessor based protective relays have numerous integrated functions that allow them to provide information on power quality events. It is proposed to utilize the existing numerical relays to analyze the quality of power at any point in the power system. The numerical relays can be programmed to capture the oscillographic waveform or any disturbance on the analogue signal or change of state of the digital signals and store it in the form of Common Format For Transient Data Exchange (COMTRADE) format. These records are then transferred to a central monitoring workstation for off-line analysis. <p>This thesis describes a technique to automate the classification and analysis of the power quality events using relay recorded data. The technique uses voltage duration and magnitude (as specified in the IEEE Std. 1159 - 1995, IEEE Recommended Practice for Monitoring Electric Power Quality) of three phases to detect and classify the events. The classified results are then presented in a user-friendly graphical form. Fast Fourier Transform (FFT) is used to estimate the fundamental frequency and harmonic components in power systems. The graphical user interface of the power quality analysis tool is developed using Microsoft Visual C++ IDE and the algorithms are programmed in C++. <p>The proposed technique was tested using data obtained by simulating different power system disturbances as well as on the data recorded by relays. The algorithms were able to classify the power quality events accurately. In the future, this facility will: enhance the real time monitoring of power quality and provide statistical analysis of available power quality data. From the utility viewpoint, it would allow them to monitor power quality in a cost effective manner and assist in preventive and predictive maintenance besides helping them to fix differential tariff based on the quality of the delivered power. It may also turn out to be a smart tool for them to penalize the consumer polluting the power quality.

Demand for electrical power is increasing everyday. Along with the increase in power demand, the characteristics of the loads are also changing. From being high power consuming, simple, robust loads, today loads are more efficient, but at the same time more sensitive. The performance and life of these highly sensitive loads depend a lot on the quality of power supplied to them. <p>Power quality is any deviation of the voltage or current waveform from its normal sinusoidal waveshape. These disturbances include, but are not limited to, sag, undervoltage, interruption, swell, overvoltage, transients, harmonics, voltage flicker and any other distortions to the sinusoidal waveform. Occurrence of one or more of such disturbances is called a power quality event. Automatic classification of these disturbances is important for quick determination of the causes and to characterize possible impacts of the disturbances.<p>Modern microprocessor based protective relays have numerous integrated functions that allow them to provide information on power quality events. It is proposed to utilize the existing numerical relays to analyze the quality of power at any point in the power system. The numerical relays can be programmed to capture the oscillographic waveform or any disturbance on the analogue signal or change of state of the digital signals and store it in the form of Common Format For Transient Data Exchange (COMTRADE) format. These records are then transferred to a central monitoring workstation for off-line analysis. <p>This thesis describes a technique to automate the classification and analysis of the power quality events using relay recorded data. The technique uses voltage duration and magnitude (as specified in the IEEE Std. 1159 - 1995, IEEE Recommended Practice for Monitoring Electric Power Quality) of three phases to detect and classify the events. The classified results are then presented in a user-friendly graphical form. Fast Fourier Transform (FFT) is used to estimate the fundamental frequency and harmonic components in power systems. The graphical user interface of the power quality analysis tool is developed using Microsoft Visual C++ IDE and the algorithms are programmed in C++. <p>The proposed technique was tested using data obtained by simulating different power system disturbances as well as on the data recorded by relays. The algorithms were able to classify the power quality events accurately. In the future, this facility will: enhance the real time monitoring of power quality and provide statistical analysis of available power quality data. From the utility viewpoint, it would allow them to monitor power quality in a cost effective manner and assist in preventive and predictive maintenance besides helping them to fix differential tariff based on the quality of the delivered power. It may also turn out to be a smart tool for them to penalize the consumer polluting the power quality.