abstract: In this work a newly fabricated organic solar cell based on a composite of fullerene derivative [6,6]-phenyl-C61 butyric acid methyl ester (PCBM) and regioregular poly (3-hexylthiophene) (P3HT) with an added interfacial layer of AgOx in between the PEDOT:PSS layer and the ITO layer is investigated. Previous equivalent circuit models are discussed and an equivalent circuit model is proposed for the fabricated device. Incorporation of the AgOx interfacial layer shows an increase in fill factor (by 33%) and power conversion efficiency (by 28%). Moreover proper correlation has been achieved between the experimental and simulated I-V plots. The simulation shows that device characteristics can be explained with accuracy by the proposed model. / Dissertation/Thesis / Masters Thesis Electrical Engineering 2015

L’optimisation de la morphologie de la couche active est primordiale pour l’augmentation des rendements des cellules solaires photovoltaïques organiques. Nous avons montré l’influence du ratio de matériaux donneur (P3HT) et accepteur (PCBM) d’électrons ainsi que de la masse molaire du P3HT sur la morphologie de la couche active. Afin de contrôler la séparation de phases entre les matériaux donneur et accepteur d’électrons, il est possible d’utiliser des copolymères à blocs afin d’aider la compatibilisation entre le P3HT et le PCBM. Nous avons choisi de synthétiser des copolymères à blocs P3HT-b-polystyrène et des P3HT-b-polyisoprène présentant une certaine compatibilité avec les matériaux de la partie active. L’ajout optimisé de P3HT-b-polyisoprène permet une augmentation de 30% des rendements et de 90% de durée de vie des cellules solaires. / Active layer morphology optimization is fundamental to achieve high efficiency in organic photovoltaic solar cells. We showed the influence of the donor (P3HT) and acceptor (PCBM) material ratio and the impact of the P3HT molecular weight on the active layer morphology. We demonstrated the possibility of using well-designed block copolymers to help P3HT and PCBM compatibilization and to control their phase separation. We chose to synthesize P3HT-b-polystyrene and P3HT-b-polyisoprene for which each block is compatible with the active materials. Optimal addition of P3HT-b-polyisoprene enables to get a 30%-improved efficiency and a 90%-enhanced lifetime of the solar cells.

In recent years, organic photovoltaics (OPVs) have attracted considerable attention as a potential source of renewable energy over traditional materials due to their light weight, low production cost, mechanically stability and compatibility with flexible substrates in roll to roll processing for high volume production. In the OPVs interface plays an important role in determining the performance of the device. Interface signifies formation of efficient contact with electrode, film, and transport of free charge carrier, which results in better performance in the device. Interface engineering also helps in improving mechanical robustness of the device. Hence, understanding of interface, modification and its evaluation is important in fabrication of efficient device. In this thesis interface is modified such that the performance of the device can be improved (chapter 3 and chapter 4). In Chapter 5 and chapter 6 interface is modified such that device can be fabricated on uncommon substrate. Fabrication of device on uncommon substrates (fiber reinforced plastic and flexible glass substrate), has unique challenges. In chapter 5 and chapter 6, we look at how interface is modified to overcome the challenges associated and also understand the role of interface in improving the performance of device on such substrates is discussed. In Chapter 1 we discuss about working of organic solar cells and the challenges associated in device fabrication. Understanding of interface to overcome challenges associated is explained. It also covers brief introduction to the succeeding chapters discussed in the thesis and its recent developments. To understand the properties of interface and to analyze device performance various characterization techniques have been used are discussed in chapter 2. This chapter also covers the materials and general device fabrication techniques used in this thesis. In chapter 3, a narrow bandgap (NBG) polymer used as a near IR sensitizer in P3HT: PCBM blend. Since, P3HT with a band gap of ~1.9 eV, the commonly used p-type material absorbs approximately ~25 % of incident light. Hence, MP2 (NBG polymer) is used along with P3HT: PCBM in active layer to form a ternary blend, which helps in increased absorption. Basic properties of MP2 are evaluated using UV-visible spectroscopy, differential scanning calaorimetry(DSC), thermogravimetric analyser (TGA), gel permeation chromatography (GPC) and photoluminescence (PL) techniques. To evaluate enhanced absorption of ternary UV-visible spectroscopy is carried out. Charge transfer from one moiety to other in ternary blend is evaluated using PL and Ttime resolved microwave conductivity (TRMC). Morphology of the ternary is assessed using atomic force microscope (AFM) and structural characterization is carried out by X-ray diffraction (XRD). Performance of the device is evaluated by current-voltage (J-V) characterizations. Further improved performance is supported by external quantum efficiency (EQE). Charge extraction with linear increasing voltage (CELIV) of the device is done to evaluate the recombination mechanism in the device and to assess the performance of the device. One-dimensional (1D) ZnO nanostructures provide direct paths for charge transport, and also offer large interfacial area to make them an ideal electron transport layer. In chapter 4 highly aligned ZnO nanorods is used as electron transport layer in OPV. Growth of ZnO nanorods is two-step processes, growing seed layer and growing ZnO nanorods from hydrothermal process using an appropriate seed layer. Two different soft-chemical solution- growth methods (upward and downward) are developed to fabricate self-assembled, oriented ZnO nanorods. Substrate mounting, surface properties and optical transmittance are optimized by varying the nanorods growth conditions. Further the ZnO nanorods are UV ozone treated and its effect on performance of nanostructured buffer layer based device is evaluated. In Chapter 5 OPV is fabricated on an opaque FRP substrate. Fabrication of OPV device on opaque substrate plastic is unique and hence understanding various properties is vital. Such devices fabrication require bottom up approach, with transparent electrode as the top electrode and metal electrode on the surface of FRP. FRP has inherent rough surface of about few microns RMS roughness. In order to reduce the roughness of the substrate FRP was planarized. The planarized layer is chosen, such that it chemically binds with the substrate. The chemical interaction between substrate and planarizing coating is evaluated by FTIR and Raman spectroscopy. The binding of planarized layer and FRP is evaluated using nanoscratch technique and surface energies are studied using contact angle measurements. In addition, adhesion properties of the metal electrodes, which are deposited on planarized FRP are evaluated using nanoscratch technique. Fabrication of OPV requires a top transparent electrode. Simple spin coating technique is used to optimize the top electrode. The property of top electrode is evaluated using UV-visible spectroscopy for transmittance, and sheet resistance of the electrode is characterized. OPV device is fabricated on planarized FRP substrate using optimized top transparent electrode and its PV properties is evaluated. Performance of the device is evaluated for two different bottom electrodes and further performance of device is enhanced using buffer layers. Usually flexible OPVs are fabricated on plastic substrate such as PET, PEN. However they are not structurally stable at high temperatures and have high oxygen and moisture Permeability. In Chapter 6 Organic based photovoltaic devices were fabricated on flexible glass. Flexible glass has high strength and it is also known for low oxygen and moisture permeability. Fabrication of device on flexible glass has never been done before and hence, generation of data is necessary for commercialization of the technology. Device fabrication is optimized by using two different transparent conducting layers (ITO- sputter deposited, PEDOT: PSS-solution processed) and device performance was evaluated for both. Since the substrate is flexible in nature understanding the performance of the device during flexing is important. For this 2-parallel plate flexural apparatus is fabricated for in-situ measurements along with current voltage measurements. These devices are flexed cyclically and performance of device is evaluated. Therefore, work discussed in the thesis show by modifying the interface of the device, and understanding various interfaces of the device is crucial for improving the performance of the device. Also by engineering the interface, devices can be fabricated on various types of substrate.

Durable, cheap, and lightweight polymer based solar cells are needed, if simply to meet the demand for decentralized electrical power production in traditionally “off-grid” areas. Using a blend of Poly(3-hexylthiophene-2,5-diyl) (P3HT), Phenyl-C61-butyric acid methyl ester (PCBM), and the low band-gap polymer Poly[2,6-(4,4-bis-(2- ethylhexyl)-4H-cyclopenta [2,1-b;3,4-b′]dithiophene)-alt-4,7(2,1,3-benzothiadiazole)] (PCPDTBT), we have fabricated devices with a wide spectral response and 3% power conversion efficiency in AM 1.5 conditions; however, this thin film system exhibits only 0.43 optical density at 500 nm. To improve the performance of this polymer blend photovoltaic, we aim to increase absorption by adding CdSe(ZnS) core (shell) quantum dots. Four groups of devices are fabricated: a control group with an active polymer layer of 16 mg/mL P3HT, 16 mg/mL PCBM, and 4 mg/mL PCPDTBT; and three groups with dispersed quantum dots at 4 mg/ml, 1 mg/mL, and 0.25 mg/mL. The (CdSe)ZnS quantum dots are coated with octadecylamine ligands and have a peak absorbance at 560 nm and peak emission at 577 nm. The active layer was dissolved in chlorobenzene solvent and spun on glass substrates, patterned with indium tin oxide. The devices were then annealed for fifteen minutes at 110° C, 140° C, and 170° C. Current-voltage characteristic curves v and optical density data were taken before and after the anneal step. Finally, surface characterization was conducted with atomic force microscopy and electrostatic force microscopy. When compared to the control, the sensitized devices exhibited increased absorption and depressed electrical performance with increasing quantum dot loading. The surface morphology, both electrical and physical, showed deviation from the typical values and patterns shown by the control that increased with quantum dot loading. When the degrading electrical characteristics, increasing optical absorbance, and surface changes, are considered together, it becomes likely that the quantum dots interact in a significant manner with the morphology of the P3HT phase, which leads to an overall decrease in performance.

Le microscope à force atomique (AFM) permet de caractériser avec une excellente résolution spatiale les surfaces d’échantillons de différentes natures et peut être mis en œuvre dans des milieux variés. Cette versatilité a favorisé le développement d’un grand nombre de techniques dérivées, destinées à investiguer diverses propriétés physiques locales. Le LGEP a ainsi réalisé un module, le Résiscope, capable de mesurer la résistance électrique locale à la surface d’un échantillon polarisé en continu, sur une gamme de 11 décades. Mise au point en mode contact, où la pointe exerce en permanence une force sur l’échantillon, cette technique fonctionne très bien sur des matériaux durs, mais trouve ses limites sur des échantillons mous ou fragiles puisque dans certaines conditions, la pointe peut altérer leur surface. Pour de tels échantillons, un mode contact intermittent, dans lequel la pointe vient à intervalles réguliers toucher très brièvement la surface, est plus approprié, mais complique la réalisation des mesures électriques. Le but de la thèse consistait à lever cette difficulté en modifiant le Résiscope pour pouvoir l’associer au « Pulsed Force Mode », mode intermittent où la pointe oscille à une fréquence de 100Hz à 2000Hz.Différentes évolutions matérielles et logicielles ont été apportées pour permettre le suivi temporel détaillé du signal de résistance électrique à chaque établissement/rupture de contact (indispensable pour passer en revue les phénomènes liés à l’intermittence), de même que pour pouvoir travailler à des vitesses de balayage acceptables. Pour l’imagerie, les meilleurs contrastes ont été obtenus grâce à une électronique de synchronisation et de traitement prenant en compte les valeurs de résistance électrique à des moments bien précis. Pour tester ce nouveau système, nous avons dans un premier temps comparé les courbes de résistance et de déflexion que nous obtenons par ce mode avec celles considérées classiquement dans le mode approche-retrait. Nous avons ensuite étudié l’influence des principaux paramètres (fréquence et amplitude d’oscillation, force d’appui, type de pointe, etc.) sur les mesures topographiques et électriques, en utilisant le HOPG comme matériau de référence. Ces essais ont notamment permis de mettre en évidence un retard quasi systématique du signal électrique par rapport au signal de déflexion (autre que le temps de mesure propre au Résiscope), dont nous n’avons pu élucider l’origine. Une fois ces connaissances acquises, nous avons étudié deux types d’échantillons organiques, l’un à caractère académique – des monocouches auto-assemblées d’alcanethiols (SAMs), l’autre à finalité plus applicative – des couches minces formées d’un réseau interpénétré de deux constituants (P3HT:PCBM) destinées aux cellules photovoltaïques. Dans les deux cas nous avons montré la pertinence de l’outil Résiscope en mode intermittent pour obtenir des informations qualitatives et quantitatives. Parallèlement à ces travaux sur matériaux fragiles, nous avons mené une étude annexe sur un phénomène de croissance de matière à caractère isolant constaté dans des conditions particulières sur différents matériaux durs, qui a été interprété comme la formation de polymère de friction sous l’effet des nano-glissements répétés associés à la déflexion du levier.Ces travaux ont été réalisés dans le cadre d’une convention CIFRE avec la société Concept Scientifique Instruments, adossée au projet ANR « MELAMIN » (P2N 2011). / The atomic force microscope (AFM) allows to characterize with excellent spatial resolution samples of different types of surfaces and can be implemented in various environments. This versatility has encouraged the development of a large number of derivative technics, intended to investigate various local physical properties. The LGEP thus achieved a module, the Résiscope, capable of measuring the local electrical resistance on the surface of a sample polarized continuously, on a range of 11 decades. Developed in contact mode, where the tip continuously exerts a force on the sample, this technic works well on hard materials, but finds its limits on soft or fragile samples since under certain conditions, the tip can alter the surface. For such samples, an intermittent contact mode, in which the tip comes at regular intervals touch very briefly the surface, is more appropriate, but complicates the achievement of electrical measurements. The aim of this thesis was to overcome this difficulty by changing the Résiscope to be able to join the "Pulsed Force Mode", intermittent mode where the tip oscillates at a frequency of 100Hz to 2000Hz. Different hardware and software changes have been made to permit the detailed temporal monitoring of the electrical resistance signal to each make / break contact (necessary to review the phenomena related to intermittency), as well as to be able to work in acceptable scan speeds. For imaging, the best contrasts were obtained through an electronic timing and treatment taking into account the electrical resistance values at specific times.To test this new system, we have initially compared resistance and deflection curves we get by this mode with those considered classically in the force-distance curves mode. We then investigated the influence of main parameters (frequency and amplitude of oscillation, setpoint, coating of the tips, etc.) on the topographical and electrical measurements, using the HOPG as reference material. These tests resulted to highlight a nearly systematic delay of the electrical signal relative to the deflection signal (other than the Resiscope measure time), which we were not able to elucidate the origin. Once these knowledge acquired, we studied two types of organic samples, one in academic nature - Self-Assembled Monolayers of alkanethiols (SAMs), the other more applicative purpose – formed of thin layers of an interpenetrating network of two components (P3HT:PCBM) for photovoltaic cells. In both cases we have shown the relevance of the Resiscope tool in intermittent mode to obtain qualitative and quantitative information. In addition to these work on fragile materials, we conducted an annex study on a phenomenon of growth material of insulating nature found in special conditions on various hard materials, which has been interpreted as the friction polymer formation as a result of repeatedly nano-sliding associated with the deflection of the cantilever. These investigations were conducted under a CIFRE agreement with the Concept Scientific Instruments company, backed by the ANR MELAMIN» (P2N 2011) project.