An important component of the cost of a radio base station comes from to the Power Amplifier driving the array of antennas. The cost can be split in Capital and Operational expenditure, due to the high design and realization costs and low energy efficiency of the Power Amplifier respectively. Both these cost components are related to the Crest Factor of the input signal. In order to reduce both costs, it would be possible to lower the average power level of the transmitting signal, whereas in order to obtain a more efficient transmission, a more energized signal would allow the receiver to better distinguish the message from the noise and interferences. These opposed needs motivate the research and development of solutions aiming at reducing the excursion of the signal without the need of sacrificing its average power level. One of the algorithms addressing this problem is the Peak Cancellation Crest Factor Reduction. This work documents the design of a hardware implementation of such method, targeting a possible future ASIC for Ericsson AB. SystemVerilog is the Hardware Description Language used for both the design and the verification of the project, together with a MATLAB model used for both exploring some design choices and to validate the design against the output of the simulation. The two main goals of the design have been the efficient hardware exploitation, aiming to a smaller area footprint on the integrated circuit, and the adoption of some innovative design solutions in the controlling part of the design, for example the managing of the cancelling pulse coefficients and the use of a time-division multiplexing strategy to further save area on the chip. For the contexts where both the solutions could compete, the proposed one shows better results in terms of area and delay compared to the current methods in use at Ericsson and also provides innovative suggestions and ideas for further improvements. / En komponent som det är viktigt att ta hänsyn till när det kommer till en radiobasstations kostnad är förstärkaren som används för att driva antennerna. Kostnaden för förstärkaren kan delas upp i en initial kostnad relaterad till utveckling och tillverkning av kretsen, samt en löpande kostnad som är relaterad till kretsens energieffektivitet. Båda kostnaderna är kopplade till en egenskap hos förstärkarens insignal, vilken är kvoten mellan signalens maximala effekt och dess medeleffekt, såkallad toppfaktor. För att reducera dessa kostnader så är det möjligt att minska signalens medeleffekt, men en hög medeleffekt förbättrar radioöverföringen eftersom det är lättare för mottagaren att skilja en signal med hög energi från brus och interferens. Dessa två motsatta krav motiverar forskning och utveckling av lösningar för att minska signalens maximala värde utan att minska dess medeleffekt. En algoritm som kan användas för att minska signalens toppfaktor är Peak Cancellation. Den här rapporten presenterar design och hårdvaruimplementering av Peak Cancellation med avsikt att kunna användas av Ericsson AB i framtida integrerade kretsar. Det hårdvarubeskrivande språket SystemVerilog användes för både design och testning i projektet. MATLAB användes för att utforska designalternativ samt för att modellera algoritmen och jämföra utdata med hårdvaruimplementationen i simuleringar. De två huvudmålen med designen var att utnyttja hårdvaran effektivt för att nå en så liten kretsyta som möjligt och att använda en rad innovativa lösningar för kontrolldelen av designen. Exempel på innovativa designlösningar som användes är hur koefficienter för pulserna, som används för reducera toppar i signalen, hanteras och användning av tidsmultiplex för att ytterligare minska kretsytan. I användningsscenarion där båda lösningarna kan konkurrera, visar den föreslagna lösningen bättre resultat när det kommer till kretsyta och latens än nuvarande lösningar som används av Ericsson. Ges också förslag på ytterligare framtida förbättringar av implementationen.

The focus of this thesis is peak-to-average power ratio (PAPR) reduction in cooperative wireless networks which exploit orthogonal frequency division multiplexing in transmission. To reduce the PAPR clipping is employed at the source node. The first contribution focuses upon an amplify-and-forward (AF) type network with four relay nodes which exploits distributed closed loop extended orthogonal space frequency block coding to improve end-to-end performance. Oversampling and filtering are used at the source node to reduce out-of-band interference and the iterative amplitude reconstruction decoding technique is used at the destination node to mitigate in-band distortion which is introduced by the clipping process. In addition, by exploiting quantized group feedback and phase rotation at two of the relay nodes, the system achieves full cooperative diversity in addition to array gain. The second contribution area is outage probability analysis in the context of multi-relay selection in a cooperative AF network with frequency selective fading channels. The gains of time domain multi-path fading channels with L paths are modeled with an Erlang distribution. General closed form expressions for the lower and upper bounds of outage probability are derived for arbitrary channel length L as a function of end-to-end signal to noise ratio. This analysis is then extended for the case when single relay selection from an arbitrary number of relay nodes M is performed. The spatial and temporal cooperative diversity gain is then analysed. In addition, exact form of outage probability for multi-path channel length L = 2 and selecting the best single relay from an arbitrary number of relay nodes M is obtained. Moreover, selecting a pair of relays when L = 2 or 3 is additionally analysed. Finally, the third contribution context is outage probability analysis of a cooperative AF network with single and two relay pair selection from M available relay nodes together with clipping at the source node, which is explicitly modelled. MATLAB and Maple software based simulations are employed throughout the thesis to support the analytical results and assess the performance of algorithms and methods.

Constantly increasing demand for wireless communications in various applications has always led to new ways of modulating the radio frequency (RF) carrier signal by advancing waveform structure throughout generations. Although communication data rates are limited by the theoretical capacity, specific signaling designs for the signal that experiences natural and artificial effects in the transmission medium such as multipath fading channel, hardware impairments and multiuser environment promised better solutions in providing improved wireless access to various type of users and networks. Besides communication capacity, broadcasting nature of radio signals poses the information security as another main concern in wireless communications. In this dissertation, new advanced methods for improving signal statistics in multiple domains are studied. Instead of focusing on a single aspect, the waveform design approaches studied in this dissertation tackle with improving the orthogonal frequency-division multiplexing (OFDM)-based signaling in multiple perspectives such as out-of-band (OOB) emission reduction, peak-to-average-power ratio (PAPR) reduction, and secure transmission with minimum or no eect at the receiver side. Various concepts are coherently exploited while achieving aforementioned goals with minimal cost such as unexplored spaces in the signal space like (CP), guard band, multipath fading; multivariate nature of the multicarrier signals; time spreading and location uniqueness of the wireless channels. The proposed techniques are analyzed theoretically and performance results are presented including related previous works in the literature. It is worth noting that the methods presented in the dissertation can be easily applicable to conventional OFDM systems thanks to having no or minimal change in the receiver structure.

Multi-carrier systems suffer from several impairments, and communication system engineers use powerful signal processing tools to combat these impairments and keep up with the capacity/rate demands. Compressed sensing (CS) is one such tool that allows recovering any sparse signal, requiring only a few measurements in a domain that is incoherent with the domain of sparsity. Almost all signals of interest have some degree of sparsity, and in this work we utilize the sparsity of impairments in orthogonal frequency division multiplexing (OFDM) and its variants (i.e., orthogonal frequency division multiplexing access (OFDMA) and single-carrier frequency-division multiple access (SC-FDMA)) to combat them using CS. We start with the problem of peak-to-average power ratio (PAPR) reduction in OFDM. OFDM signals suffer from high PAPR and clipping is the simplest PAPR reduction scheme. However, clipping introduces inband distortions that result in compromised performance and hence needs to be mitigated at the receiver. Due to the high PAPR nature of the OFDM signal, only a few instances are clipped, these clipping distortions can be recovered at the receiver by employing CS. We then extend the proposed clipping recovery scheme to an interleaved OFDMA system. Interleaved OFDMA presents a special structure that result in only self-inflicted clipping distortions. In this work, we prove that distortions do not spread over multiple users (while utilizing interleaved carrier assignment in OFDMA) and construct a CS system that recovers the clipping distortions on each user. Finally, we address the problem of narrowband interference (NBI) in SC-FDMA. Unlike OFDM and OFDMA systems, SC-FDMA does not suffer from high PAPR, but (as the data is encoded in time domain) is seriously vulnerable to information loss owing to NBI. Utilizing the sparse nature of NBI (in frequency domain) we combat its effect on SC-FDMA system by CS recovery.

Yes / High Peak-to-Average-Power Ratio (PAPR) of transmitted signals is a common problem in broadband telecommunication systems using an orthogonal frequency division multiplexing (OFDM) modulation scheme, as it increases transmitter power consumption. In consumer applications where it impacts mobile terminal battery life and infrastructure running costs, this is a major factor in customer satisfaction. Companding techniques have been recently used to alleviate this high PAPR. In this paper, a companding scheme with an offset, amidst two nonlinear companding levels, is proposed to achieve better PAPR reduction while maintaining an acceptable bit error rate (BER) level, resulting in electronic products of higher power efficiency. Study cases have included the effect of companding on the OFDM signal with and without an offset. A novel closed-form approximation for the BER of the proposed companding scheme is also presented, and its accuracy is compared against simulation results. A method for choosing best companding parameters is presented based on contour plots. Practical emulation of a real time OFDM-based system has been implemented and evaluated using a Field Programmable Gate Array (FPGA).

Radio frequency (RF) spectrum congestion motivates the search for alternative communication techniques to complement radio systems. Visible light communications (VLC) is an emerging technology that exploits the recent and ever-growing increase in the usage of energy-efficient light emitting diodes (LEDs) to imperceptibly modulate the optical power output of LEDs to enable communication and augment RF networks. Orthogonal frequency-divison multiplexing (OFDM) has been proposed as a modulation scheme for VLC due to its high spectral efficiency, ease of channel estimation and equalization, resistance to inter-symbol interference (ISI) and frequency-selective fading, efficient implementation using the Fast Fourier Transform (FFT), and compatibility with RF and power-line communication (PLC) standards that use OFDM. One of the major drawbacks of conventional OFDM techniques is the high peak-to-average power ratio (PAPR) of OFDM signals. The peaks of the OFDM signals are clipped due to the limited dynamic range of the LED, which translates the high PAPR of the OFDM signal into non-linear distortion (NLD). This signal distortion causes bit-error rate (BER) performance degradation, especially at high optical signal-to-noise ratios (SNRs) typical of indoor VLC scenarios. In this thesis, a new family of modulation techniques, termed spatial optical OFDM (SO-OFDM), is proposed with the aim of reducing the PAPR of conventional DC-biased optical OFDM (DCO-OFDM) by making use of the large number of LEDs typically available in indoor lighting settings. Each LED group signal is a narrowband signal consisting of a small number of subcarriers, and thus has a smaller PAPR than the original OFDM signal. Firstly, SO-OFDM is introduced and its two key concepts of frequency-to-space mapping and spatial summing are explained. Frequency-to-space mapping is achieved by allocating a subset of OFDM subcarriers to each LED. Each LED group signal is a narrowband signal consisting of a small number of subcarriers, and thus has a smaller PAPR than the original OFDM signal. Several design variations of the subcarrier assignment to LEDs are introduced and are shown through simulations, to reduce PAPR, and NLD noise due to clipping, and improve the BER performance at high SNRs as compared to DCO-OFDM. In addition, luminous efficacy is identified as an important lighting design parameter that is impacted by modulation. Relative luminous efficacy is defined as the ratio of the luminous efficacy of a modulated LED to that of an LED driven by a DC signal, and is introduced as a metric to assess the impact of modulation on LED lighting. Relative luminous efficacy links communication parameters such as signal variance to lighting design requirements. Secondly, a low-complexity amplify-and-forward (AF) scheme is proposed for an integrated power-line communication/visible-light communication (PLC/VLC) where SO-OFDM is used for the VLC link. Frequency translation of the incoming PLC signal is used to increase the usable bandwidth of the LED. The use of both frequency translation and SO-OFDM leads to capacity gains over DCO-OFDM in the high SNR regime. Finally, a low-complexity variant of SO-OFDM, termed square-wave SO-OFDM (SW-SO-OFDM), is proposed. Square-wave SO-OFDM uses square-wave carriers instead of sinusoidal waves to modulate a single OFDM subcarrier signal per LED. By using square-wave carriers, SW-SO-OFDM eliminates the need for digital-to-analog converters (DACs), digital predistortion (DPD), and the FFT operation. Squarewave SO-OFDM is also shown, through simulations, to achieve BER performance gains over SO-OFDM and DCO-OFDM. In addition, an experimental demonstration of SW-SO-OFDM with 64 QAM modulation on subcarriers is described. / Thesis / Doctor of Philosophy (PhD) / Visible-light communications (VLC) is an emerging technology that exploits the increasingly widespread use of light-emitting diodes (LEDs) for indoor lighting, and modulates the optical power output of the LED for data transmission. Among the various modulation techniques that have been proposed for VLC, orthogonal frequency-division multiplexing (OFDM) offers high data rates, resistance to channel impairments, and simple channel estimation and equalization. However, OFDM signals suffer from a high peak-to-average power ratio (PAPR) which degrades the efficiency of the power amplifier in the transmitter and hinders the communication performance. In this thesis, a new multiple-LED modulation technique, termed spatial optical OFDM (SO-OFDM), is proposed to reduce the PAPR. Using a frequency-to-space mapping, SO-OFDM divides the wideband high-PAPR OFDM signal into multiple narrowband low-PAPR signals and assigns each signal to a group of LEDs. Spatial summing of the transmitted signals occurs at the receiver allowing for the use of a conventional OFDM receiver. Several variations of SO-OFDM are introduced and are shown, using simulations, to reduce the PAPR, combat non-linear distortion (NLD), and improve the bit-error rate (BER) performance at high signal-to-noise ratios (SNRs), typical of VLC systems. Spatial optical OFDM is also applied to a practical scenario where its PAPR reduction capability is used to improve the overall capacity of a proposed system that integrates power-line communication (PLC) and VLC. A low-complexity variant of SO-OFDM, that uses square-wave carriers and simplifies the transmitter design by eliminating the need for digital predistortion (DPD) and digital-to-analog converters (DACs) is also proposed, and tested experimentally.

Les techniques multiporteuses de type OFDM sont aujourd'hui largement déployées dans tous les systèmes de communication sans fils notamment dans les réseaux cellulaires (L TE), les réseaux de diffusion (DVB) ou encore les réseaux WiFi. Cependant, les modulations multiporteuses se caractérisent par une très grande dynamique mesurée par le Peak to Average Power Ratio (PAPR), ce qui empêche d'alimenter l'amplificateur de puissance non linéaire (utilisé avant l'émission des signaux) à son point optimal et ainsi conduit à diminuer son efficacité énergétique. Des techniques de réduction du PAPR peuvent alors être mises en oeuvre pour réduire le PAPR du signal et des techniques de prédistorsion peuvent alors être utilisées pour compenser les non-linéarités de l'amplificateur de puissance. L'approche développée dans le cadre de cette thèse a pour objectif d'étudier une solution intelligente pour les implémentations futures pour contrôler la réduction du PAPR et les étapes de linéa risation de manière flexible en fonction de certains paramètres prédéfinis afin qu'ils deviennent adaptatifs et auto-configurables. Plus précisément, notre travail a principalement porté sur l'analyse des différentes distorsions dans la bande (in-band distortions)mesurées par I'EVM ou Error Vector Magnitude et en dehors de la bande de transmission (out-of-band distortions) mesurées par I'ACPR ou Adjacent Channel Power Ratio de signaux à porteuses multiples. En particulier de nombreux résultats analytiques complétés par des résultats de simulation permettant d'évaluer I'EVM et I'ACPR en fonction des caractéristiques de l'amplification nonlinéaire en prenant en compte ou pas l'effet mémoire de l'amplificateur et la mise en oeuvre de techniques d'écrêtage et de pré-distorsion ont été obtenus. Ces résultats constituent une étape importante dans l'optimisation globale de la complexité, de la linéarité et de l'efficacité énergétique des émetteurs aussi bien pour la diffusion de la télévision numérique que pour les réseaux cellulaires de 4 ème génération (L TE) ou de 5""' génération. / OFDM multicarrier techniques are now widely deployed in most wireless communication systems, in particular in cellularnetworks (L TE), broadcast networks (DVB) and WiFi networks. However, multi-carrier modulations are characterized by avery large dynamic amplitude measured by the Peak to Average Power Ratio (PAPR). which prevents radio frequencydesigners to feed the signal at the optimal point of the Power Amplifier (PA) which reduces the PA energy efficiency. Inliterature, the PAPR reduction and linearization techniques are the main approaches to solve the PAPR problem, the PAnonlinearities problem. as well as the low PA efficiency problem.The approach developed in this thesis was to study an intelligent solution for future implementations to control thereduction of PAPR and the linearization steps in a flexible way according to some predefined parameters so that theybecome adaptive and self-configurable. More specifically, our work focused on the analytical analysis of in-band measureby the Error Vector Magnitude (EVM) and out-of-band distortions measured by the Adjacent Chanel Power Ratio (ACPR)for clipped multicarrier signals taking into account the impact of non-linear amplification, memory effects and predistortion.In particular. many analytical results complemented by simulation results to evaluate the EVM and ACPR are proposed.These analytical expressions depend on the PA characteristics taking into account or not the PA memory effects and theuse of clipping and pre-distortion techniques. lt is worthwhile to note that our proposed theoretical analyses could be veryuseful for optimizing future transmitter efficiency and linearity in the field of broadcasting applications for the deployment oDVB-T2 transmitters as well as for L TE cellular networks.