Modern Panamax Pure Car and Truck Carriers (PCTC) have become more vulnerable to critical roll responses as built in margins have been traded against increased transport efficiency. The research presented in this licentiate thesis aims at enhancing the predictability and control of these critical roll responses. The thesis presents the development of a new method for assessing the roll damping, which is a crucial parameter for predicting roll motions. The method involves a unique set up of full scale in-service trials and is straightforward, cost efficient and shows a good potential. The thesis also includes a demonstration of a new application for rudder control to be used for mitigation of parametric roll. This is performed by simulating real incidents that have occurred with PCTC’s in service. Simulations with rudder roll control show promising results and reveal that the approach could be very efficient for mitigation of parametric roll. Last but not least an approach for monitoring of roll induced stresses, so-called racking stresses in PCTC’s, is presented. The approach involves measurement of the ship motions and scaling of pre-calculated structural responses from global finite element analysis. Based on full scale motion and stress measurements from a PCTC in-service the approach is evaluated and demonstrated to be an efficient alternative to conventional methods. / <p>QC 20130424</p>

<p>This is a master thesis conducted at KTH Centre for Naval Architecture in collaboration with Wallenius Marine AB.</p><p>Rolling motions is something that is undesired in all kinds of seafaring. In terms of propulsion resistance, comfort and route planning it would be desirable to reduce these motions. This thesis is an investigation on how different roll stabilising systems affect the performance of an 8000 unit PCTC vessel, special emphasis is put on investigating the performance of anti roll tanks. The ship in question has a recorded incidence of parametric rolling and the ability of the tanks to countervail this phenomenon is also investigated.</p><p>The tank and fin stabilising systems are relatively equal when it comes to roll damping performance related to changes in the required forward propulsion power. The tanks however, have a higher potential for improvements, addition of features such as heeling systems and parametric roll prevention systems.</p><p>The tank performance is also independent of the speed of the ship. The tanks are easier to retrofit and do not require the ship to be put in dry dock during installation. The conclusion of this thesis is that a combined anti roll and heeling system should be installed but that a further study has to be made on the performance of active rudder stabilisation.</p><p>It is shown that passive tanks are efficient at preventing parametric rolling in some sea states. A proposal is made for a further study on a control system that could achieve the same performance for all sea states.</p> / <p>HTML clipboard Detta är ett examensarbete utfört på KTH Marina System i samarbete med Wallenius Marine AB.</p><p>Rullningsrörelser är något som är oönskat i all form av sjöfart. Framsteg kan göras i både framdrivningsmotstånd, komfort och ruttplanering om dessa rörelser kunde minskas. Detta examensarbete består av en undersökning hur olika system för rulldämpning påverkar prestandan hos ett 8000 enheters PCTC-fartyg. Speciell vikt har lagts vid att undersöka prestandan hos antirulltankar. Det undersökta fartyget har en dokumenterad incident med parametrisk rullning och tankarnas förmåga att motverka detta fenomen undersöks.</p><p>Tank- och fenstabilisatorer är i princip likvärdiga vad det gäller dämpningsprestanda relaterat till erforderliga ändringar i framdrivningseffekten. Tankarna har dock en större potential för förbättring och tillägg av ytterligare inslag som krängningshämmare och system för motverkan av parametrisk rullning. Tankarnas prestanda är också oberoende av fartygets fart.</p><p>Tankarna är lättare att installera i efterhand och kräver inte att fartyget läggs i torrdocka under installationen. Slutsatsen av detta arbete är att en kombinerad antirull- och krängningshämmande tank bör installeras men att en vidare studie måste göras på prestandan hos aktiva roderstabiliseringssystem.</p><p>Det visas att passiva tankar kan motverka parametrisk rullning i vissa sjötillstånd. Ett förslag om en vidare studie på reglersystem som skulle kunna ge samma prestanda vid alla sjötillstånd ges.</p><p> </p>

This is a master thesis conducted at KTH Centre for Naval Architecture in collaboration with Wallenius Marine AB. Rolling motions is something that is undesired in all kinds of seafaring. In terms of propulsion resistance, comfort and route planning it would be desirable to reduce these motions. This thesis is an investigation on how different roll stabilising systems affect the performance of an 8000 unit PCTC vessel, special emphasis is put on investigating the performance of anti roll tanks. The ship in question has a recorded incidence of parametric rolling and the ability of the tanks to countervail this phenomenon is also investigated. The tank and fin stabilising systems are relatively equal when it comes to roll damping performance related to changes in the required forward propulsion power. The tanks however, have a higher potential for improvements, addition of features such as heeling systems and parametric roll prevention systems. The tank performance is also independent of the speed of the ship. The tanks are easier to retrofit and do not require the ship to be put in dry dock during installation. The conclusion of this thesis is that a combined anti roll and heeling system should be installed but that a further study has to be made on the performance of active rudder stabilisation. It is shown that passive tanks are efficient at preventing parametric rolling in some sea states. A proposal is made for a further study on a control system that could achieve the same performance for all sea states. / HTML clipboard Detta är ett examensarbete utfört på KTH Marina System i samarbete med Wallenius Marine AB. Rullningsrörelser är något som är oönskat i all form av sjöfart. Framsteg kan göras i både framdrivningsmotstånd, komfort och ruttplanering om dessa rörelser kunde minskas. Detta examensarbete består av en undersökning hur olika system för rulldämpning påverkar prestandan hos ett 8000 enheters PCTC-fartyg. Speciell vikt har lagts vid att undersöka prestandan hos antirulltankar. Det undersökta fartyget har en dokumenterad incident med parametrisk rullning och tankarnas förmåga att motverka detta fenomen undersöks. Tank- och fenstabilisatorer är i princip likvärdiga vad det gäller dämpningsprestanda relaterat till erforderliga ändringar i framdrivningseffekten. Tankarna har dock en större potential för förbättring och tillägg av ytterligare inslag som krängningshämmare och system för motverkan av parametrisk rullning. Tankarnas prestanda är också oberoende av fartygets fart. Tankarna är lättare att installera i efterhand och kräver inte att fartyget läggs i torrdocka under installationen. Slutsatsen av detta arbete är att en kombinerad antirull- och krängningshämmande tank bör installeras men att en vidare studie måste göras på prestandan hos aktiva roderstabiliseringssystem. Det visas att passiva tankar kan motverka parametrisk rullning i vissa sjötillstånd. Ett förslag om en vidare studie på reglersystem som skulle kunna ge samma prestanda vid alla sjötillstånd ges.

Modern volume carriers such as container vessels, cruise ships and Pure Car and Truck Carriers (PCTC’s) have become more vulnerable to critical roll responses as built in margins have been traded against increased transport efficiency. The research presented in this doctoral thesis aims at enhancing the predictability and control of these critical roll responses. The thesis presents a holistic framework for predicting and assessing the roll damping, which is a crucial parameter for predicting roll motions, based on a unique combination of full scale trials, model tests, semi-empirical methods and computational fluid dynamics. The framework is intended to be used from the early design stage and gradually improved until delivery of the ship and finally to provide input for decision support in the operation. The thesis also includes a demonstration of a new application for rudder control to be used for mitigation of parametric roll. This is performed by simulating real incidents that have occurred with PCTC’s in service. Simulations with rudder roll control show promising results and reveal that the approach could be very efficient for mitigation of parametric roll. Finally, an approach for monitoring of roll induced stresses, so-called racking stresses in PCTC’s, is presented. The approach involves measurement of the ship motions and scaling of pre-calculated structural responses from global finite element analysis. Based on full scale motion and stress measurements from a PCTC in-service the approach is evaluated and demonstrated to be an efficient alternative to conventional methods. / <p>QC 20170516</p>