This thesis is to design an LED driver circuit with constant output current and Power Factor Correction(PFC) control. Switching power converter is applied for power stage of the LED driver circuit, a non-insulated Buck converter without transformer is used, and the inductor current of Buck converter is operating in Continuous Conduction Mode(CCM). According to the operating principle of Buck converter, the equivalent mathematical model and system block diagram is developed to establish the traditional closed loop PFC control circuit. The controller parameters are set up by time-domain and frequency-domain analysis to achieve the goal with constant output current and PFC control. Furthermore, the thesis presents a more effective PFC control method to reduce the cost of multiplier used in traditional PFC control method and overcome the congenital defect of Buck converter. Both two PFC control methods are confirmed and compared by simulation and experiment. The results show that the proposed control method has more effective performance and achieve constant output current for LED with high power factor by 0.966 under full-load condition.

A constant switching frequency with the sixth-order harmonic injection PWM concept is established, and a sixth-order harmonic injection technique is developed for the harmonic reduction of a single-switch three-phase boost rectifier. The approach employs a constant duty cycle with sixth-order harmonic injection to suppress the dominant (fifth-order) harmonic in the input currents. Hence, to meet the THD<10% requirement, the rectifier voltage gain can be designed down to 1.45; to meet the IEC 1000-3-2 (A) standard, the output power can be pushed up to 10 kW for the application with a 3X220 V input and a 800 V output. The results are verified on a 6-kW prototype. The injection principle is graphically explained in current waveforms and mathematically proved. Two injection methods are proposed to meet either the THD requirement or the IEC standard. The injection implementation and design guidelines are provided. The boost inductor design and EMI filter design are discussed. An average small- signal model based on the equivalent multi-module model is developed and experimentally verified. The variations of the small-signal model against load are demonstrated, and the compensator design is discussed. The results show that at no load, the dominant pole of the control-to-output transfer function approaches the origin and causes more phase delay, making the control design difficult. To avoid the no load case and to simplify the control design, a 50-W dummy load (1% of the full load) is added. Finally, a simple nonlinear gain control circuit is presented to mitigate the load effect and reduce the dummy load to 10 W. / Master of Science

Five new single-stage power factor correction (PFC) techniques are developed for single-phase applications. These converters are: Integrated single-stage PFC converters, voltage source charge pump power factor correction (VS-CPPFC) converters, current source CPPFC converters, combined voltage source current source (VSCS) CPPFC converters, and continuous input current (CIC) CPPFC converters. Integrated single-stage PFC converters are first developed, which combine the PFC converter with a DC/DC converter into a single-stage converter. DC bus voltage stress at light load for the single-stage PFC converters are analyzed. DC bus voltage feedback concept is proposed to reduce the DC bus voltage stress at light load. The principle of operations of proposed converters are presented, implemented and evaluated. The experimental results verify the theoretical analysis. VS-CPPFC technique use a capacitor in series with a high frequency voltage source to achieve the PFC function. In this way, the input inductor is eliminated. VS-CPPFC AC/DC converters are developed, and their performance is evaluated. VS-CPPFC electronic ballasts with and without dimming function are also presented. The average lamp current control with duty ratio modulation is developed so that the lamp operates in constant power with a low crest factor over the line variation. The experimental results verify the CPPFC concept. CS-CPPFC technique employs a capacitor in parallel with a high frequency current source to obtain the PFC function. The unity power factor condition and principle of operation are analyzed. By doing so, the switch has less switching current stress, and deals only with the resonant inductor current. Design considerations and experimental results of the CS-CPPFC electronic ballast are presented. VSCS-CPPFC technique integrates the VS-CPPFC with the CS-CPPFC converters. The circuit derivation, unity power factor condition and design considerations are presented. The developed VSCS-CPPFC converters has constant lamp operation, low crest factor with a high power factor even without any feedback control. CIC-CPPFC technique is developed by inserting a small inductor in series with the line rectifier for the conceptual VS-CPPFC, CS-CPPFC and VSCS-CPPFC circuits. The circuit derivation and its unity power factor condition are discussed. The input current can be designed to be continuous, and a small line input filter can be used. The circulating current in the resonant tank and the switching current stress are minimized. The average lamp current control with switching frequency modulation is developed, so the developed electronic ballast operates in constant power, low crest factor. The developed CIC-CPPFC electronic ballast has features of low line input current harmonics, constant lamp power, low crest factor, continuous input current, low DC bus voltage stress, small circulating current and switching current stress over a wide range of line input voltage. / Ph. D.

The conventional power factor correction circuit has a fixed output voltage. However, in some applications, a PFC circuit with a wide output voltage range is needed. A single phase power factor correction circuit with wide output voltage range is developed in this work. After a comparison of two main power stage candidates (Buck+Boost and Sepic) in terms of efficiency, complexity, cost and device rating, the buck+boost converter is employed as the variable output PFC power stage. From the loss analysis, this topology has a high efficiency from light load to heavy load. The control system of the variable output PFC circuit is analyzed and designed. Charge average current sensing scheme has been adopted to sense the input current. The problem of high input harmonic currents at low output voltage is discussed. It is found that the current loop gain and cross over frequency will change greatly when the output voltage changes. To solve this problem, an automatic gain control scheme is proposed and a detailed circuit is designed and added to the current loop. A modified input current sensing scheme is presented to overcome the problem of an insufficient phase margin of the PFC circuit near the maximum output voltage. The charge average current sensing circuit will be bypassed automatically by a logical circuit when the output voltage is higher than the peak line voltage. Instead, a resistor is used to sense the input current at that condition. Therefore, the phase delay caused by the charge average current sensing circuit is avoided. The design and analysis are based on a novel air conditioner motor system application. Some detailed design issues are discussed. The experimental results show that the variable output PFC circuit has good performance in the wide output voltage range, under both the Boost mode when the output voltage is high and the Buck+Boost mode when the output voltage is low. / Master of Science

In the thesis, LED driver circuits which are applied in low power lighting LED with constant output current and Power Factor Correction are presented. The non-isolated Buck converter are used for the LED drivers. According to different operating mode of inductance current, Power Factor Correction are realized with both the method of Voltage Follower Approach Control under Discontinuous Conduction Mode and the method of Nonlinear Carrier Control under Continuous Conduction Mode. NLC doesn¡¦t need the multiplier which is used in traditional power factor correction, therefore NLC can reduce the system cost. The designed circuits are verified by simulation of IsSpice software and practical experiments. From simulation and experimental results, it shows the proposed approaches achieve the goal with high power factor and constant output current.

This thesis presents the design and implementation of a single-stage with high power factor asymmetrical half-bridge converter. The main structure combines a boost converter with an asymmetrical half-bridge. An Asymmetrical half-bridge converter has many advantages such as soft-switching properties and fewer components. Therefore it is suitable for DC/DC cell. The boost converter is used in a PFC cell that operating in discontinuous condition mode have innate ability of power factor correction without additional controller. In this thesis, the complete analysis of operation principle and design of controller for the equivalent circuits of a single-stage AC/DC converter in every operating stage have been described in detail. Finally, we construct the single-stage circuit and experimental result show that it can reach the expected goal for power-factor correction.

The thesis aims to the research of active power factor correction (PFC) circuit and develop a DSP-based digital controller. In the thesis, PI controller is the control core for the voltage loop¡Band current loop, and then achieve the function of the power factor correction of boost converter. Finally, we develop a boost converter and connect it to a DSP-based controller to measure the waveforms and verify the power factor correction. Furthermore, the research can be extended to a simulating platform which we can verify the power factor correction by just changing the control law on DSP .

Fluorescent lamps are nowadays the most important light sources in industrial, commercial, and domestic applications. To drive fluorescent lamps, electronic ballasts with high-frequency resonant inverter, instead of the electromagnetic ones, are increasingly used due to the benefits of lightweight, small size, high luminous efficiency, and long lamp life. Recently, efforts are concentrated on how to reduce the product cost as well as to improve the circuit performances. To further curtail the product cost, the power-factor-correction circuit is integrated into the ballast circuit as single-stage high-power-factor electronic ballast. On the other hand, the unit cost per lamp can be substantially reduced by developing a ballast circuit which is capable of driving multiple lamps. For convenient use, the user may turn on the desired number of the lamps in accordance with the expected luminosity. A starting-aid circuit is added to eliminate the glow current during preheating. In addition, a protection circuit will be included in the multi-lamp electronic ballast. In case of operating partial lamps, a high power factor at the line input will be always retained. In this thesis, the feasible circuit configuration is developed and design equations are derived. Accordingly, design guidelines for determining circuit parameters are provided. The laboratory circuits are built and tested to verify the computer simulations and analytical predictions.

In this thesis, the design of a Switching Power Supply for switched-reluctance motor drive system power factor correction is presented. Switching power technology for the power supply is now widely used, which has the main advantages of high efficiency and small size. However, the traditional type of Switching Power Supply will reduce the impact on electricity usage and quality, and produce electricity pollution and waste, for example low power factor, and high harmonic distortion. In order to improve the power factor, this paper used the traditional method of multiplier power factor correction circuit, and the use of state-space averaging method to analysis Buck Derived Converters to implement the Switching ¡@ Reluctance Motor Drive circuit design; In addition, this thesis used the Average Current Control method to cause the inductor current to follow a sinusoidal signal, achieving the purpose of¡@power factor correction.The design of Buck Converters is based on switching theory. With this method, the electricity pollution problems introduced by switching reluctance motor drives is solved by the Averagingmethod derived form the converters. The mathematical Buck Converter model is brought into a block diagram, based on the design of Buck¡@Converters, and then simulated with PsPICE software. Finally the design of the output voltage control, compensation and current control loop is performed.

In the thesis, an LED driver circuit that is applied in low power lighting LED with constant output current and Power Factor Correction (PFC) is presented. The insulated Flyback converter is used for the LED driver. Power Factor Correction is realized with both the method of Voltage Follower Approach Control under Discontinuous Conduction Mode and the method of Boundary Conduction Control under Boundary Conduction Mode. Compared with Voltage Follower Approach Control, Boundary Conduction Control needs only output current feedback. Moreover, it possesses lesser magnetize inductance current, lesser electrical stress of elements, more flexible choice of elements specification, smaller output current ripples, and higher power factor under light load. The circuit design is expounded, and verified by IsSpice simulation and experiment result.