41 |
Estudo teórico e experimental sobre padrões de escoamento, fração de vazio e perda de pressão durante escoamento bifásico água-ar cruzado ascendente externo a banco de tubos / Theoretical and experimental study on flow pattern, void fraction and pressure drop during air-water two-phase upward crossflow through tube bundlesKanizawa, Fábio Toshio 21 November 2014 (has links)
O presente trabalho envolve um estudo teórico e experimental do escoamento bifásico externo a banco de tubos. Inicialmente, apresenta-se uma ampla revisão da literatura sobre padrões de escoamento, fração de vazio e perda de pressão, durante escoamentos monofásicos e bifásicos externos a banco de tubos. Nesta análise são também descritos os métodos de previsão destes parâmetros. Verificam-se diferenças significativas entre as estimativas proporcionadas por eles, fato que indica a inexistência de métodos generalizados. Posteriormente é apresentada uma descrição detalhada da bancada experimental projetada e construída durante o doutoramento. O aparato completo compõe-se da seção de testes, circuito de água, sistema de compressão e condicionamento de ar, e seções de injeção dos fluxos e condicionamento do escoamento. A seção de testes consiste em um banco de tubos distribuídos segundo configuração triangular normal, com os tubos apresentando diâmetro externo de 19,1 mm, comprimento de 381 mm, e espaçamento transversal de 24 mm. Os experimentos foram realizados para escoamento vertical ascendente de misturas água-ar e velocidades superficiais da fase líquida e gás de 0,020 a 1,500 m/s e de 0,10 a 10,00 m/s, respectivamente. Neste estudo foram desenvolvidas técnicas inéditas para determinação experimental da fração de vazio superficial no interior do banco de tubos baseadas em sistemas óptico e de sensoriamento capacitivo. Os padrões de escoamento foram identificados subjetivamente através de visualização de imagens e vídeos do escoamento, e objetivamente com o auxílio do método de agrupamento de dados k-means utilizando parâmetros baseados no sinal de perda de pressão e do sensoriamento capacitivo. Identificou-se subjetivamente os padrões de escoamento bolhas, bolhas dispersas, bolhas grandes, agitante, intermitente e anular. Constatou-se equivalência entre os padrões de escoamento identificados através dos métodos objetivo e subjetivo. Resultados experimentais para fração de vazio foram obtidos através de técnicas óptica e capacitiva. Constatou-se que o traçador rodamina B utilizado no método óptico altera as condições do escoamento, ainda que em concentrações reduzidas. A partir dos resultados obtidos com o sensoriamento capacitivo estimou-se a fração de vazio para o padrão bolhas. Resultados para a parcela friccional da perda de pressão também foram levantados. Constata-se o incremento da fração de vazio e da parcela friccional da perda de pressão com as velocidades superficiais das fases líquida e gás. Os resultados para fração de vazio foram comparados com métodos de previsão da literatura, e de maneira geral os métodos preveem as tendências dos resultados experimentais apenas para vazões de líquido reduzidas. Analogamente, os resultados para perda de pressão foram comparados com estimativas segundo métodos da literatura, concluindo que os métodos não preveem satisfatoriamente os resultados obtidos. Desta forma, foram propostos novos métodos de previsão para padrões de escoamento, fração de vazio e parcela friccional da perda de pressão, desenvolvidos a partir de análises dos mecanismos dominantes do escoamento, e adotando parâmetros adimensionais para correlacionar os dados. Os métodos propostos preveem satisfatoriamente os resultados experimentais deste estudo e da literatura para escoamentos bifásicos água-ar. / The present thesis concerns a theoretical and experimental study of external two-phase flows across tube bundles. Initially, a comprehensive literature review covering flow patterns, void fraction and pressure drop for single and two-phase flows across tubes bundle is presented. The review also describes predictive methods for these parameters. A comparison of these methods reveals reasonable disagreement among their predictions, indicating the absence of generalized methods. Subsequently, the apparatus and instrumentation designed and built to obtain the experimental data are described. The experimental apparatus comprises the test section, a water loop, air compression and conditioning systems, and sets for fluid flow injections and conditioning. The test section is a normal triangular tube bundle, with 19.1 mm OD tubes, 381 mm long and transversal pitch of 24 mm. The experiments were performed for air-water upward vertical flow, for superficial liquid and gas velocities ranging from 0.020 to 1.500 m/s and 0.10 to 10.00 m/s, respectively. Innovative techniques to evaluate the void fraction within the bundle were developed based on capacitive and optical methods. The flow patterns were identified subjectively and objectively by k-means clustering method, using as clustering parameters the pressure drop and the capacitive signals. Bubbles, dispersed bubbles, large bubbles, churn, intermittent and annular flow patterns were identified subjectively. The data groups identified by the objective method are representative of the flow patterns. Void fraction measurements were obtained for bubbly flow using both techniques (optical and capacitive). The void fraction data based on the optical method had its experimental range limited due to changes in the flow characteristics caused by the addition of the fluorescent dye Rhodamine B. The experimental results indicate that the void fraction increases with increasing the superficial velocities of both phases. In general, the void fraction predictive methods available in the literature capture the trends of the experimental results only for reduced liquid flow rates. According to the experimental results, the frictional pressure drop increases asymptotically with increasing the flow rates of both phases. None of the predictive methods from literature evaluated in the present study predicted satisfactorily the experimental results. Methods for prediction of flow patterns, void fraction and frictional pressure drop parcel were also developed in the present study. These methods provided reasonable predictions of the experimental results obtained in the present study, and also from the literature for air and water flows across tube bundles.
|
42 |
Optimization of Heat Sinks with Flow Bypass Using Entropy Generation MinimizationHossain, Md Rakib January 2006 (has links)
Forced air cooling of electronic packages is enhanced through the use of extended surfaces or heat sinks that reduce boundary resistance allowing heat generating devices to operate at lower temperatures, thereby improving reliability. Unfortunately, the clearance zones or bypass regions surrounding the heat sink, channel some of the cooling air mass away from the heat sink, making it difficult to accurately estimate thermal performance. The design of an "optimized" heat sink requires a complete knowledge of all thermal resistances between the heat source and the ambient air, therefore, it is imperative that the boundary resistance is properly characterized, since it is typically the controlling resistance in the path. Existing models are difficult to incorporate into optimization routines because they do not provide a means of predicting flow bypass based on information at hand, such as heat sink geometry or approach velocity. <br /><br /> A procedure is presented that allows the simultaneous optimization of heat sink design parameters based on a minimization of the entropy generation associated with thermal resistance and fluid pressure drop. All relevant design parameters such as geometric parameters of a heat sink, source and bypass configurations, heat dissipation, material properties and flow conditions can be simultaneously optimized to characterize a heat sink that minimizes entropy generation and in turn results in a minimum operating temperature of an electronic component. <br /><br /> An analytical model for predicting air flow and pressure drop across the heat sink is developed by applying conservation of mass and momentum over the bypass regions and in the flow channels established between the fins of the heat sink. The model is applicable for the entire laminar flow range and any type of bypass (side, top or side and top both) or fully shrouded configurations. During the development of the model, the flow was assumed to be steady, laminar, developing flow. The model is also correlated to a simple equation within 8% confidence level for an easy implementation into the entropy generation minimization procedure. The influence of all the resistances to heat transfer associated with a heat sink are studied, and an order of magnitude analysis is carried out to include only the influential resistances in the thermal resistance model. Spreading and material resistances due to the geometry of the base plate, conduction and convection resistances associated with the fins of the heat sink and convection resistance of the wetted surfaces of the base plate are considered for the development of a thermal resistance model. The thermal resistance and pressure drop model are shown to be in good agreement with the experimental data over a wide range of flow conditions, heat sink geometries, bypass configurations and power levels, typical of many applications found in microelectronics and related fields. Data published in the open literature are also used to show the flexibility of the models to simulate a variety of applications. <br /><br /> The proposed thermal resistance and pressure drop model are successfully used in the entropy generation minimization procedure to design a heat sink with bypass for optimum dimensions and performance. A sensitivity analysis is also carried out to check the influence of bypass configurations, power levels, heat sink materials and the coverage ratio on the optimum dimensions and performance of a heat sink and it is found that any change in these parameters results in a change in the optimized heat sink dimensions and flow conditions associated with the application for optimal heat sink performance.
|
43 |
Optimization of Heat Sinks with Flow Bypass Using Entropy Generation MinimizationHossain, Md Rakib January 2006 (has links)
Forced air cooling of electronic packages is enhanced through the use of extended surfaces or heat sinks that reduce boundary resistance allowing heat generating devices to operate at lower temperatures, thereby improving reliability. Unfortunately, the clearance zones or bypass regions surrounding the heat sink, channel some of the cooling air mass away from the heat sink, making it difficult to accurately estimate thermal performance. The design of an "optimized" heat sink requires a complete knowledge of all thermal resistances between the heat source and the ambient air, therefore, it is imperative that the boundary resistance is properly characterized, since it is typically the controlling resistance in the path. Existing models are difficult to incorporate into optimization routines because they do not provide a means of predicting flow bypass based on information at hand, such as heat sink geometry or approach velocity. <br /><br /> A procedure is presented that allows the simultaneous optimization of heat sink design parameters based on a minimization of the entropy generation associated with thermal resistance and fluid pressure drop. All relevant design parameters such as geometric parameters of a heat sink, source and bypass configurations, heat dissipation, material properties and flow conditions can be simultaneously optimized to characterize a heat sink that minimizes entropy generation and in turn results in a minimum operating temperature of an electronic component. <br /><br /> An analytical model for predicting air flow and pressure drop across the heat sink is developed by applying conservation of mass and momentum over the bypass regions and in the flow channels established between the fins of the heat sink. The model is applicable for the entire laminar flow range and any type of bypass (side, top or side and top both) or fully shrouded configurations. During the development of the model, the flow was assumed to be steady, laminar, developing flow. The model is also correlated to a simple equation within 8% confidence level for an easy implementation into the entropy generation minimization procedure. The influence of all the resistances to heat transfer associated with a heat sink are studied, and an order of magnitude analysis is carried out to include only the influential resistances in the thermal resistance model. Spreading and material resistances due to the geometry of the base plate, conduction and convection resistances associated with the fins of the heat sink and convection resistance of the wetted surfaces of the base plate are considered for the development of a thermal resistance model. The thermal resistance and pressure drop model are shown to be in good agreement with the experimental data over a wide range of flow conditions, heat sink geometries, bypass configurations and power levels, typical of many applications found in microelectronics and related fields. Data published in the open literature are also used to show the flexibility of the models to simulate a variety of applications. <br /><br /> The proposed thermal resistance and pressure drop model are successfully used in the entropy generation minimization procedure to design a heat sink with bypass for optimum dimensions and performance. A sensitivity analysis is also carried out to check the influence of bypass configurations, power levels, heat sink materials and the coverage ratio on the optimum dimensions and performance of a heat sink and it is found that any change in these parameters results in a change in the optimized heat sink dimensions and flow conditions associated with the application for optimal heat sink performance.
|
44 |
Two-Phase Flow Within Narrow AnnuliDillon, Chad Michael 12 July 2004 (has links)
A study of two-phase flow in annular channels with annular gaps of less than 1 mm is useful for the design and safety analysis of high power density systems such as accelerator targets and nuclear reactor cores. Though much work has been done on pressure drop in two-phase flow, designers rely mostly on empirical models and correlations; hence, it is valuable to study their applicability for different channel sizes, geometries, and gas qualities.
The pressure drop along a concentric annular test section was measured for cases of either constant quality or variable quality along its length (such as in sub-cooled and flow boiling). A porous tube was used to inject gas along the inner surface of the annular channel, thereby simulating the case of flow boiling along the inner surface. The data were compared to predictions of various models and correlations. Additionally, the effect of wall vibrations on the pressure drop was examined. Experiments were conducted by imposing vibrations of known amplitudes and frequencies on the outer tube of the annulus. Wall vibrations were thought to be important for flow in microchannels where the vibration amplitudes may be significant compared to the channel hydraulic diameter.
The results obtained in this investigation indicate that the pressure drop correlation given by Beattie and Whalley provides the best agreement with the data for both porous tube gas injection (i.e. variable quality) and constant quality two-phase flow within the narrow annulus. Furthermore, the results show that there is a minimal effect of vibrations on two-phase pressure drop over the range of frequencies and amplitudes studied.
|
45 |
Analytical and Experimental Study of Annular Two-Phase Flow Friction Pressure Drop Under MicrogravityNguyen, Ngoc Thanh 2009 December 1900 (has links)
Two-phase liquid-gas flow has a wide variety of applications in space, including active thermal control systems, high-power communications satellites, heat pumps and space nuclear reactors. Two-phase systems have many potential advantages over current single-phase systems due to reductions in system size, weight and power consumption. The mechanisms of pressure drop, heat transfer coefficients, void fractions, and flow regimes must be well understood under microgravity conditions in order to design reliable two-phase systems. The main objective of this present research is to develop a new mathematical model that can accurately predict the annular two-phase friction pressure drop to optimize the design of two-phase systems. The two-phase flow tests were conducted aboard the NASA KC-135 aircraft by the Interphase Transport Phenomena (ITP) group from Texas A&M University. The two-phase flow pressure drops were measured across a single transparent test section 12.7 mm ID and 1.63 m long in annular regimes under microgravity conditions during two flight campaigns. Different from previous work, this was the first time both the void fraction and the film thickness were measured under microgravity conditions. The empirical correlations for the interfacial friction factor and void fraction were developed from 57 experimental data using a linear least squares regression technique. The annular two-phase friction pressure drop can be predicted by the new mathematical model requiring only knowledge of the length and diameter of the tube, liquid and vapor mass flow rates, and properties of the working fluid. In addition, the new mathematical model was validated using Foster-Miller & ITP data collected over twelve flights aboard the KC-135 with working fluid R-12 (77 data points), Sundstrand data collected aboard the KC-135 with working fluid R-114 (43 data points) and Zhao and Rezkallah data aboard the KC-135 with working fluid water and air (43 data points). Compared with the LockhartMartinelli model, Wheeler model, Chen model and homogeneous model, the new mathematical model is the optimal model for predicting the two-phase friction pressure drop in annular regimes. The majority of the data falls within +-20% of the proposed correlation and the average error is 12%.
|
46 |
Undersökning av tryckfall relaterat till avstånd mellan två 90 graders krökar i cirkulär ventilationskanalKellner, Philip January 2015 (has links)
Due to higher standards of living around the world, greater industries and larger infrastructures causes an increase of the global energy consumption. This harvest of energy puts a great stress on the global environment. With this development, it becomes increasingly important to utilize energy resources in the best possible way. Fans are components that are often used in the industry and in households. A common problem is that the fan is oversized. An oversized fan causes an excessive flow, which has to be adjusted in order to achieve the correct flow. This results in larger energy usage than the use of a properly sized fan. When designing a ventilation system calculations have to be made in order to determine the total pressure loss of the system. A series of simplifications are applied when using theoretical calculations. The total pressure loss of the system is assumed to be the sum of the pressure loss of each component in the system. This simplification ignores the separation distance that exists between each component. In reality, when air passes through the components, swirls emerge and a distortion of the velocity profile occurs. This causes large pressure losses due to friction losses occurring between the fluid and the pipe wall. The recommendation given in HVAC installations states that two 90 degree elbows should not be placed closer to each other than 6D (D representing the hydraulic diameter of the pipe) to thereby prevent large pressure drops. This dissertation will address the following questions: The recommendation in HVAC installations states that two 90 degree elbows should not be placed closer to each other than 6D (D representing the hydraulic diameter of the pipe) to thereby prevent large pressure drops. Does this recommendation conform with the empirical data obtained from conducted experiments? What is the relation between the pressure drop and the separation distance between two 90 degree elbows? In this dissertation a series of experiments are conducted where pressure loss measurements are made within a circular ventilation duct with two integrated 90 degree elbows. Pressure loss measurements within a U-shaped piping system are made at five different fluid velocities each at 11 different separation distances between the two 90 degree elbows. By analysis of the obtained empirical data and by comparing it to the recommendation no results were found to validate this statement.
|
47 |
Condensation of pure hydrocarbons and zeotropic mixtures in smooth horizontal tubesMacDonald, Malcolm 21 September 2015 (has links)
A study of the condensation of hydrocarbons and zeotropic hydrocarbon mixtures in smooth horizontal tubes was conducted. Measurements of condensation heat transfer coefficients and frictional pressure drop were taken over a range of mass fluxes (G = 150 – 450 kg m-2 s-1), a range of reduced pressures (Pr = 0.25 - 0.95), for two tube diameters (D = 7.75 and 14.45 mm), several working fluid-to-coolant temperature differences (ΔTLM = 3 – 14°C) and temperature glides (ΔTGlide) between 7 - 14°C. The wide range of conditions investigated in this study provides considerable insight on the transport phenomena influencing condensation in pure fluids and their mixtures. The trends in heat transfer coefficient and frictional pressure gradient are discussed and compared with the predictions of correlations from the literature. The results of the experiments, combined with previous flow visualization studies on hydrocarbons, were used to develop physically consistent heat transfer and frictional pressure gradient models that are applicable to pure fluids and zeotropic mixtures. A framework was developed for zeotropic mixture condensation that recommends a specific modeling approach based on the observed trends in the heat transfer coefficient and the points of deviations from pure fluid trends.
The documentation of the condensation heat transfer and pressure drop behavior of environmentally friendly refrigerants, and the development of accurate correlations, will facilitate their widespread introduction as a working fluid for refrigeration cycles. Furthermore, the accurate pure fluid models, which serve as a baseline case for zeotropic mixture modeling, yield more effective predictions of zeotropic mixture condensation, which will lead to increased efficiencies of chemical processing plants.
|
48 |
Two-phase flow in a mini-size impacting tee junction with a rectangular cross-sectionElazhary, Amr Mohamed Ali 27 July 2012 (has links)
An experimental study was conducted in order to investigate the two-phase-flow phenomena in a mini-size, horizontal impacting tee junction. The test section was machined in an acrylic block with a rectangular cross-section of 1.87-mm height × 20-mm width on the inlet and outlet sides. Air-water mixtures at 200 kPa (abs) and room temperature were used as the test fluids.
Four flow regimes were identified visually: bubbly, plug, churn, and annular over the ranges of gas and liquid superficial velocities of 0.04 ≤ JG ≤ 10 m/s and 0.02 ≤ JL ≤ 0.7 m/s, respectively, and a flow regime map was developed. The present flow-regime map was compared with several experimental maps. It is thought from those comparisons that the channel height has a more significant role in determining the flow-regime boundaries than the hydraulic diameter. The two-phase fully-developed pressure gradient was measured in the inlet and the outlet sides of the junction for six different inlet conditions and various mass splits at the junction. Comparisons were conducted between the present data and former correlations. The correlations that agreed best with the present data were identified.
Five single-phase test sets were performed. In each set of experiments, the pressure distribution was measured for the whole range of the mass split ratio, Wi/W1. The pressure drop at the junction at each value of Wi/W1 was calculated. Values of the pressure-loss coefficient, , were calculated at various Wi/W1 and inlet Reynolds number. The pressure-loss coefficient was strongly dependent on the inlet Reynolds number in the laminar region, while the results for the turbulent region were almost coincident. Numerical simulations of single-phase flow in an impacting tee junction of identical dimensions to that of the present test-section were performed to confirm the results of the experiments.
Phase-redistribution experiments were conducted covering all four inlet flow regimes and models were proposed for predicting the experimental data. Good agreement in terms of magnitude and trend was obtained between the present experimental data and the proposed model. New correlations were developed for the single- and two-phase pressure drop in the junction.
|
49 |
Design and Development of an Experimental Apparatus to Study Jet Fuel Coking in Small Gas Turbine Fuel NozzlesLiang, Jason Jian 04 December 2013 (has links)
An experimental apparatus was designed and built to study the thermal autoxidative carbon deposition, or coking, in the fuel injection nozzles of small gas turbine engines. The apparatus is a simplified representation of an aircraft fuel system, consisting of a preheating section and a test section, which is a passage that simulates the geometry, temperatures, pressures and flow rates seen by the fuel injection nozzles. Preliminary experiments were performed to verify the functionality of the apparatus. Pressure drop across the test section was measured throughout the experiments to monitor deposit buildup, and an effective reduction in test section diameter due to deposit blockage was calculated. The preliminary experiments showed that the pressure drop increased more significantly for higher test section temperatures, and that pressure drop measurement is an effective method of monitoring and quantifying deposit buildup.
|
50 |
Design and Development of an Experimental Apparatus to Study Jet Fuel Coking in Small Gas Turbine Fuel NozzlesLiang, Jason Jian 04 December 2013 (has links)
An experimental apparatus was designed and built to study the thermal autoxidative carbon deposition, or coking, in the fuel injection nozzles of small gas turbine engines. The apparatus is a simplified representation of an aircraft fuel system, consisting of a preheating section and a test section, which is a passage that simulates the geometry, temperatures, pressures and flow rates seen by the fuel injection nozzles. Preliminary experiments were performed to verify the functionality of the apparatus. Pressure drop across the test section was measured throughout the experiments to monitor deposit buildup, and an effective reduction in test section diameter due to deposit blockage was calculated. The preliminary experiments showed that the pressure drop increased more significantly for higher test section temperatures, and that pressure drop measurement is an effective method of monitoring and quantifying deposit buildup.
|
Page generated in 0.0183 seconds