Semiconductor nanocrystal-based photovoltaics are an interesting new technology with the potential to achieve high efficiencies at low cost. CuInSe2 nanocrystals have been synthesized in solution using arrested precipitation and dispersed in solvent to form a “solar ink”. The inks have been deposited under ambient conditions to fabricate photovoltaic devices with efficiency up to 3%. Despite the low cost spray coating deposition technique, device efficiencies remain too low for commercialization. Higher efficiencies up to 7% have been achieved using a high temperature selenization process, but this process is too expensive. New nanocrystal film treatment processes are necessary which can improve the device efficiency at low cost. To this end, CuInSe2 nanocrystals were synthesized using a diphenyl phosphine:Se precursor which allows for precise control over the nanocrystal size. The size is controlled by changing the temperature of the reaction. The smallest size nanocrystals demonstrated extremely high device open circuit voltage. Ligand exchange procedures were used to replace the insulating oleylamine capping ligand used during synthesis with more conductive halide ions or inorganic chalcogenidometallate cluster (ChaM) ligands. These ligands led to improved charge transport in the nanocrystal films. A high-intensity pulsed light processing technique known as photonic curing was used which allows for high temperature sintering of nanocrystal films on temperature-sensitive substrates. High energy pulses cause the nanocrystals to sinter into large grains, primarily through melting and resolidification. The choice of metal back contact has a dramatic effect on the final film morphology, with Au and MoSe2 back contacts providing much better adhesion with the CuInSe2 than Mo back contacts. Nanocrystal sintering without melting can be achieved by replacing the oleylamine ligands with ChaM ligands prior to photonic curing. Low energy photonic curing pulses vaporize the oleylamine ligands without inducing sintering or grain growth. This greatly improved nanocrystal coupling and interparticle charge transport. Multiexcitons were successfully extracted from these nanocrystal films and external quantum efficiencies over 100% were observed. Transient absorption spectroscopy was used to study the multiexciton generation process in CuInSe2 nanocrystal films and colloidal suspensions. The multiexciton generation efficiency, threshold, and Auger lifetimes for CuInSe2 compare well with other nanocrystal materials. / text

Occurrence of organic micropollutants (OMPs) in aquatic environment is a worldwide concern. A long list of anthropogenic substances, including pharmaceuticals, hormones, etc., are frequently detected in natural water sources. Wastewater treatment plants are one main source of OMPs pollution, but also a key step to control OMPs dissemination into the environment. This dissertation focuses on the evaluation of Membrane Aerated Biofilm Reactor (MABR) as a sustainable process to treat wastewater polluted by OMPs. Furthermore, application of high intensity pulsed light is proposed as an innovative tertiary treatment to produce reclaimed water of high quality. In Chapter 1, a literature review was performed to investigate the occurrence and toxicity of 12 selected organic micropollutants (OMPs) in surface and ground water and the limitations of current available biological processes. Among these technologies, systems with enriched nitrifying activity were able to enhance the removal of specific OMPs through cometabolic activities. Thus, I proposed the use of a MABR with enriched nitrifying biomass to treat OMP polluted water. In Chapter 2, I studied the influence of biofilm thickness on the removal of 13 OMPs via MABR. Results demonstrated OMP removal was dependent on biofilm thickness and bacterial cell density. MABR demonstrated important efficiencies in the removal of ammonium, COD, acetaminophen and triclosan at early stages of biofilm thickness. However, the removal of nonpolar, hydrophobic 4 OMPs and anionic, acidic OMPs required thicker biofilms, achieving maximum removal at biofilm with 1.02 mm thickness and 2.2 × 106 cell mL-1. In Chapter 3, the contribution of sorption and biodegradation in the removal of OMPs via MABR was evaluated. At three stages of biofilm thickness studied, biodegradation dominated the removal for most OMPs. Heterotrophs played an important role in OMP biodegradation at all biofilm thickness, while autotrophic nitrifiers enhanced their contribution at thickness beyond 0.58 mm. Increased removal of pollutants like estrone and ethinyl estradiol were linked to the MABR enrichment with nitrifying bacteria. Sorption was essential for the removal of lipophilic and recalcitrant pollutants like triclosan. Finally, to provide high quality treated water for reuse, Chapter 4 explores the use of high-intensity pulsed light (HIPL) as post-treatment. The number of pulses and optical energy dose have a significant impact on the OMPs removal. HIPL demonstrated fast kinetics and efficient photodegradation – with significant OMPs removal within milliseconds. The findings from my Ph.D. dissertation indicate that MABR combined with high-intensity pulse light may be an effective treatment train for the efficient removal OMPs present in municipal wastewaters. This combined treatment process could potentially pave the way to produce high quality reclaimed water for various reuse purposes.