No description available.

Existing specifications for asphalt cement employ insufficient aging and conditioning times prior to testing and low strains during the actual test which are insufficient to predict asphalt performance, especially if the materials are modified with additives such as those used for warm mix technology. However, slightly modified protocols, like increasing the conditioning time in the bending beam rheometer (BBR) test and increasing the aging duration in the pressure aging vessel (PAV), predict asphalt performance better than the current Superpave™ specification. These improved protocols are published as new test standards through the collaborative effort between the Ontario Ministry of Transportation and Queen’s University. In this study, the effects of warm mix and other additives on rheological, aging and failure properties are investigated. The properties are measured by regular tests and by modified protocols. The latter include the extended BBR test (LS-308) and the double-edge-notched tension (DENT) test (LS-299). Changes in ductile strain tolerance within base asphalts due to the various additives as measured with the DENT test were found to be very significant. The DENT results like essential work of fracture, we, plastic work of fracture term, βwp, and critical crack tip opening displacement, CTOD, are usually helped to correlate with the cracking distress survey results of the pavement in service. The addition of amide and polyethylene waxes risks increasing the cracking susceptibility in the pavement. They show a negative effect on strain tolerance in the ductile state, which is likely to show up as premature and/or excessive cracking in service which is similar to their physical hardening behavior from low temperature grading and extended BBR testing. / Thesis (Master, Chemistry) -- Queen's University, 2013-02-26 11:10:41.08

This thesis discusses and documents findings from an investigation of performance-based testing of asphalt cement (AC), warm mixed asphalt cement, asphalt rubber (AR), and warm asphalt rubber. A number of control, warm, and asphalt rubber binders from Ontario construction contracts were investigated for their compliance with conventional Superpave® test methods such as rolling thin film (RTFO), pressure aging vessel (PAV), dynamic shear rheometer (DSR), and bending beam rheometer (BBR), as well as additional specification tests such as extended BBR and double edge notched tension test. The quality and durability of those binders were determined. Quality means the ability of asphalt binder to reach a set of specific properties whereas durability is the measure of how well asphalt retains its original characteristics when exposed to normal weathering and aging process. One warm AC and two field-blended asphalt rubber samples showed high levels of physical hardening which can lead to premature and early cracking. The warm asphalt cement lost 8 °C when stored isothermally for three days at low temperatures according to Ontario’s extended bending beam rheometer (BBR) protocol (LS-308). The two asphalt rubber samples lost 10 °C and 12 °C following the same conditioning. Many of the studied asphalt samples showed deficient strain tolerance as measured in Ontario’s double-edge-notched tension (DENT) test (LS-299). In a study of warm rubberized asphalt cement with improved properties, a number of compositions were prepared with soft Cold Lake AC and a small quantity of naphthenic oil. These binders showed little chemical and physical hardening and reasonable critical crack tip opening displacements (CTOD). Strain tolerance was much improved by co-blending with a high vinyl type styrene-butadiene-styrene (SBS) polymer and a small amount of sulfur. / Thesis (Master, Chemistry) -- Queen's University, 2013-04-24 22:54:20.07

This doctoral thesis consists of a literature review, presented in two papers, and another six papers describing experimental studies of the influence of different kinds of wax and polyphosporic acid on bitumen and asphalt concrete mixture properties. The literature review should give an extensive description of the field of knowledge concerning wax in bitumen. Effects of wax in crude oil, bitumen and asphalt concrete as well as test methods for studying these effects are described. Theories behind possible mechanisms are also discussed, and commercial wax as additive to bitumen for different purposes included. The experimental parts comprise laboratory studies involving totally five 160/220 penetration base bitumens from different sources, two isolated bitumen waxes, five commercial waxes and one polyphosphoric acid. Asphalt concrete slabs, containing base or modified bitumen were prepared and tested. Binder properties were evaluated using different types of laboratory equipment, such as dynamic shear rheometer (DSR), bending beam rheometer (BBR), differential scanning calorimeter (DSC), force ductilometer, as well as equipment for determining conventional parameters like penetration, softening point, viscosity, and Fraass breaking point. Fourier Transform Infrared (FTIR) spectroscopy and Thin Layer Chromatography (TLC-FID) were used for chemical characterization. The binders were aged by means of the rolling thin film oven test (RTFOT) and pressure ageing vessel (PAV) in combination. Asphalt concrete properties were evaluated at low temperatures using the tensile strain restrained specimen test (TSRST) and creep test at -25°C. Dynamic creep testing was performed at 40°C, as well as complex modulus tests between 0 and 20°C. Binder test results indicated that the magnitude and type of effect on bitumen rheology depend on the bitumen itself, type of crystallizing fraction in the bitumen and/or type and amount of additive used. Bitumen composition was found to be of decisive importance. Adding polyethylene wax or polyphosphoric acid, especially to a non-waxy 160/220 penetration grade bitumen, showed no or positive effects on the rheological behaviour at low temperatures (decrease in stiffness) as well as medium and high temperatures (increase in complex modulus and decrease in phase angle). However, the corresponding positive effects could not be shown in dynamic creep testing (at 40°C) of asphalt concrete mixtures containing these modified binders. Adding FT-paraffin decreased the physical hardening index for all bitumens. Also polyethylene wax and montan wax showed this effect for some bitumens. Slack wax showed a large increasing effect on physical hardening, and polyphosphoric acid none or a minor negative effect. No correlation between physical hardening index (PHI) and wax content by DSC was found in this study, involving both natural bitumen wax and commercial wax. Addition of the commercial waxes used showed no or marginally positive influence on bitumen ageing properties for the bitumens and test conditions used. Comparing asphalt mixture test results to the corresponding binder test results, the effects on asphalt mixtures from adding commercial wax or polyphosphoric acid were less evident. Significant binder physical hardening by BBR could not be confirmed by TSRST. / QC 20101006