Neste trabalho é apresentado o projeto de uma antena planar de formato de F-invertido (PIFA) com ranhura-T para aplicação nos sistemas de comunicações sem fio GSM/UMTS/WCDMA. As larguras de banda da antena são aumentadas em função do aproveitamento dos modos ressonantes implícitos no plano de terra. Uma análise paramétrica é feita visando a obtenção de desempenho equilibrado na antena. As diversas simulações do desempenho da antena são realizadas com o software SEMCAD, que utiliza o método das diferenças finitas no domínio do tempo (FDTD). No trabalho é avaliada a diferença de desempenho da antena com e sem a presença do aparelho celular e também próximo à cabeça do usuário. Deste modo, é observada uma influência negativa sobre o desempenho da antena causada pela presença da cabeça do usuário. Adicionalmente, boa concordância é observada entre os dados do modelo simulado e os resultados medidos do protótipo. / This work presents the design and implementation of a planar inverted F-type antenna (PIFA) slot-T for wireless mobile communications GSM/UMTS/WCDMA. The excitation of the ground plane modes is used to increase the antenna bandwidth. A parametric analysis is done to obtain a balanced performance of the antenna. The several antenna performance simulations are performed with the SEMCAD software, which use the finite difference time domain (FDTD) method. In addition the differences in performance of the antenna are evaluated with and without the presence of the cell phone housing and the user's head, thus, negative influence on the antenna performance caused by the presence of the user's head is observed. Finally a prototype is implemented to get an idea of the real behavior of the proposed antenna. Good agreement is observed between data of the simulated model and measured results of the prototype.

Neste trabalho é apresentado o projeto de uma antena planar de formato de F-invertido (PIFA) com ranhura-T para aplicação nos sistemas de comunicações sem fio GSM/UMTS/WCDMA. As larguras de banda da antena são aumentadas em função do aproveitamento dos modos ressonantes implícitos no plano de terra. Uma análise paramétrica é feita visando a obtenção de desempenho equilibrado na antena. As diversas simulações do desempenho da antena são realizadas com o software SEMCAD, que utiliza o método das diferenças finitas no domínio do tempo (FDTD). No trabalho é avaliada a diferença de desempenho da antena com e sem a presença do aparelho celular e também próximo à cabeça do usuário. Deste modo, é observada uma influência negativa sobre o desempenho da antena causada pela presença da cabeça do usuário. Adicionalmente, boa concordância é observada entre os dados do modelo simulado e os resultados medidos do protótipo. / This work presents the design and implementation of a planar inverted F-type antenna (PIFA) slot-T for wireless mobile communications GSM/UMTS/WCDMA. The excitation of the ground plane modes is used to increase the antenna bandwidth. A parametric analysis is done to obtain a balanced performance of the antenna. The several antenna performance simulations are performed with the SEMCAD software, which use the finite difference time domain (FDTD) method. In addition the differences in performance of the antenna are evaluated with and without the presence of the cell phone housing and the user's head, thus, negative influence on the antenna performance caused by the presence of the user's head is observed. Finally a prototype is implemented to get an idea of the real behavior of the proposed antenna. Good agreement is observed between data of the simulated model and measured results of the prototype.

Neste trabalho é apresentado o projeto de uma antena planar de formato de F-invertido (PIFA) com ranhura-T para aplicação nos sistemas de comunicações sem fio GSM/UMTS/WCDMA. As larguras de banda da antena são aumentadas em função do aproveitamento dos modos ressonantes implícitos no plano de terra. Uma análise paramétrica é feita visando a obtenção de desempenho equilibrado na antena. As diversas simulações do desempenho da antena são realizadas com o software SEMCAD, que utiliza o método das diferenças finitas no domínio do tempo (FDTD). No trabalho é avaliada a diferença de desempenho da antena com e sem a presença do aparelho celular e também próximo à cabeça do usuário. Deste modo, é observada uma influência negativa sobre o desempenho da antena causada pela presença da cabeça do usuário. Adicionalmente, boa concordância é observada entre os dados do modelo simulado e os resultados medidos do protótipo. / This work presents the design and implementation of a planar inverted F-type antenna (PIFA) slot-T for wireless mobile communications GSM/UMTS/WCDMA. The excitation of the ground plane modes is used to increase the antenna bandwidth. A parametric analysis is done to obtain a balanced performance of the antenna. The several antenna performance simulations are performed with the SEMCAD software, which use the finite difference time domain (FDTD) method. In addition the differences in performance of the antenna are evaluated with and without the presence of the cell phone housing and the user's head, thus, negative influence on the antenna performance caused by the presence of the user's head is observed. Finally a prototype is implemented to get an idea of the real behavior of the proposed antenna. Good agreement is observed between data of the simulated model and measured results of the prototype.

No description available.

Novel antennas attractive to fit in the internal space of a PDA (Personal Digital Assistant) for WLAN (Wireless Local Area Network) operations are presented in this dissertation. The proposed antennas have in common good impedance bandwidth (defined by 10 dB return loss), covering the dual-band WLAN operation in the 2.4/5.2 GHz bands. Two novel designs of foam-base surface-mount antennas are proposed in Chapters 2 and 3. Surface-mountable antennas, compared with ceramic antennas, are generally low cost in fabrication and rigid in nature. Low-profile and good dual-band operation of the proposed surface-mountable antennas can be observed in Chapters 2 and 3, and in addition, a few present-day WLAN bands at 5 GHz are covered in the operating bandwidths of the proposed foam-base surface-mountable shorted monopole antenna, shown in Chapter 3. Finally, in Chapter 4, a novel planar helical antenna printed on both surfaces of a dielectric substrate is demonstrated. This patent-pending helical antenna is very suitable to print and integrate on a circuit board of a PDA device for 2.4/5.2 GHz WLAN operation.

Abstract In this dissertation, the operation of planar impulse radio (IR) ultra wideband (UWB) antennas is examined for use in wireless body area networks (WBANs). The objective of the thesis is to consider electromagnetic phenomena due to coupling between an antenna and human body tissues and to analyse the challenges of wideband radiators. The aim is to understand the fundamental behaviour of an antenna in a WBAN, focusing on off-body and on-body communications. The thesis premises follow the international WBAN standard 802.15.6-2012 by the Institute of Electrical and Electronics Engineering (IEEE) and the Federal Communications Commission’s (FCC) UWB regulations (3.1–10.6 GHz). In the examinations, the frequency-dependent modelling of human tissues is considered. The impact of the variation of tissue layer thickness on the performance of an antenna is depicted. The demonstration of the impact of antenna input power is given in terms of generation of heat in tissues and specific absorption rate (SAR). In order to theoretically contemplate the effect of reflections due to tissues on antenna patterns, the opportunities to influence polarization with an artificially anisotropic substrate are derived. With the proposed method, not earlier proposed for WBAN antennas, the smooth patterns without pattern minima can be achieved over the FCC UWB bandwidth. In addition, a theoretical two-path model is applied to the estimation of the antenna pattern shape close to tissues. Various antenna parameters are explored as a function of the use distance to tissue surface to demonstrate the behaviour in the vicinity of a body. The size of the reactive near-field is an important factor for the evaluation of satisfactory on-body performance. The proportions of absorption, mismatch and body losses are analysed close to a body. The connection between the complex input impedance and the dimensions of planar antennas is analysed by using lumped-element equivalent circuits. The impact of the actual width and length of the radiator on the impedance behaviour is presented for the first time. In addition, impedance is analysed in terms of capacitance, inductance and resistance within the reactive near-field for the first time. In order to understand the impact of tissues close to the antenna, the parasitic components for the stages in equivalents are proposed. / Tiivistelmä Tässä väitöskirjassa tarkastellaan laajakaistaisten impulssiradioantennien (IR-UWB) toimintaa langattomissa kehoverkoissa (WBAN). Työn tavoitteena on tarkastella antennin ja ihmiskudoksen kytkeytymisestä johtuvia sähkömagneettisia ilmiöitä ja analysoida laajakaistaisen säteilijän haasteet. Päämääränä on ymmärtää antennin suorituskyky kontekstissa ja kohdeympäristöksi on fokusoitu toiminta kehon pinnalla (on-body) ja keholta poispäin seuraavaan liityntäpisteeseen (off-body). Tutkimustyö pohjautuu IEEE802.15.6-2012-standardiin sekä FCC:n UWB -säännöksiin. Väitöstyössä tarkastellaan taajuusriippuvan ihmiskudoksen mallintamista. Ihmiskudoskerrosten paksuuden vaikutusta antennin suorituskykyyn tutkitaan simuloimalla. Lisäksi tarkastellaan antennin syöttötehon vaikutusta kudoksen lämpiämisen ja tehon absorboitumisen näkökulmasta. Kehon aiheuttamien heijastusten vaikutusta säteilykuvioihin tarkastellaan teoreettisesti ja lisäksi esitetään menetelmä vaikuttaa antennin summapolarisaation kautta säteilykuvion muotoon keinotekoisella epäisotrooppisella substraatilla. Ehdotetulla menetelmällä, mitä ei ole aiemmin kirjallisuudessa esitetty kehoantenneille, voidaan minimoida nollakohtia ja saavuttaa tasainen säteilykuvio FCC UWB -taajuuskaistan yli. Kaksitie-mallia sovelletaan säteilykuvion muodon ennustamiseen kehon läheisyydessä. Useita antenniparametreja havainnollistetaan antennin käyttöetäisyyden funktiona ihmiskudoksesta. Antennin reaktiivisen lähikentän koko on tärkeä tekijä kehoantennille riittävän suorituskyvyn saavuttamiseksi. Absorptio-, epäsovitus- ja kehohäviöiden osuudet edelleen eritellään ja analysoidaan työssä. Työssä tutkitaan kompleksisen syöttöimpedanssin ja antennin fyysisten mittojen yhteyttä hyödyntämällä erilliskomponenteilla muodostettuja vastinpiirejä. Ensimmäistä kertaa antennin käytännön leveyden ja pituuden muutos esitetään suhteessa impedanssikäyttäytymiseen. Impedanssin muutos analysoidaan kapasitanssin, induktanssin ja resistanssin funktiona antennin reaktiivisen lähikentän alueella. Jotta kudoksen vaikutus antennin läheisyydessä voitaan ottaa suunnittelussa huomioon, työssä esitetään tarvittavat parasiittiset komponentit vastinkytkentöjen sarja- ja rinnanasteisiin.

The master’s thesis deals in first part with the design of a single antenna element of an antenna array for receiving the digital TV. The resonant frequency of the antenna is 4.7 GHz, the antenna operates in the frequency band 4.4 to 5.0 GHz. Properties of the antenna are verified in programs CST Microwave Studio and Ansoft Designer. The final antenna element is experimentally produced. The second part is devoted to microstrip divider, 2x2 elements antenna array and 4x4 elements antenna array. The antenna array 4x4 elements was produced and its properties were measured.

This thesis deals with the analysis of a planar antenna operating at two frequencies with use frequency doubling. The design and simulation of the antenna in ANSOFT Designer is described. The antenna is designed for two operating frequencies 900 MHz and 1.8 GHz. The antenna is required to operate TM10 mode and TM01 modes.

This master’s thesis is focused on the properties and types of helical antennas. The helical antenna work in the different modes. These modes are described in this thesis. There are also discussed possibility for design a dual-band helical antennas. The main aim of this work is the selection of a suitable solution and design a dual-band helical antenna for the WiFi band working at resonance frequencies of 2,4 GHz and 5 GHz. The simulation of this antenna was performed in the program CST Microwave studio.

The diploma thesis is aimed to design, optimize, produce and subsequently measure the properties of the reflector with the electronic steering direction for the frequency of the 24,125 GHz band ISM. The problem chosen is solved by a group of voltage-controlled varicaps. The reflector consists of a matrix of two rows, each containing 3 cells. The reflector was designed by full-wave software CST Microwave Studio 2015.