Spelling suggestions: "subject:"flanar laserinduced fluorescence"" "subject:"flanar laserinducerad fluorescence""
21 |
Development and Application of Burst-Mode Planar Laser Diagnostics for Detonating and Hypersonic FlowsAustin M Webb (17543874) 04 December 2023 (has links)
<p dir="ltr">Burst-mode lasers and burst-mode optical parametric oscillators (OPOs) are applied and developed for planar laser induced fluorescence (PLIF) measurements of key species for high-speed combustion measurements. OH-PLIF in the rotating detonation engine was performed for the first time at wave structure visualization in two different planes and was 10 times faster than any other burst mode OH-PLIF measurements at the time. The same system was used to perform another OH-PLIF experiment at 1 MHz for ~200 pulses to compare key features of the detonation wave structure with computational fluid dynamic simulations and a fundamental detonation tube experiment. The system was also used for seedless velocity measurements in the exhaust by tracking a pocket of OH with a technique called FLASH. A similar OPO was built, aligned, and tuned to perform 1 MHz NO PLIF in a Mach 10 hypersonic tunnel to visualize second mode instabilities and calculate the frequency in the boundary layer transition of a 7-degree cone. A high-efficiency OPO was developed and characterized utilizing the KTP crystal to provide narrow bandwidth pulses for the fluorescence of multiple species. The OPO was pumped at repetition rates up to 1 MHz and was calculated to have a 1.9% UV efficiency from the fundamental 1064 nm output. This is 3 – 5 times increase in efficiency from previous custom and commercial built OPOs. The OPO was applied to the RDC for OH PLIF in the combustor channel and NO PLIF for injector dynamics and response studies. Lastly, a burst-mode laser was used to perform LII on the post detonation blast flow field to measure explosively generated soot. The data was taken at 1 MHz and compared and corrected with a separate set of experiments and computational simulations.</p>
|
22 |
Experimental investigation of multi-component jets issuing from model pipeline geometries with application to hydrogen safetySoleimani nia, Majid 21 December 2018 (has links)
Development of modern safety standards for hydrogen storage infrastructure requires fundamental insight into the physics of buoyant gas dispersion into ambient air. Also, from a practical engineering stand-point, flow patterns and dispersion of gas originating from orifices in the side wall of circular pipe or storage tank need to be studied. In this thesis, novel configurations were considered to investigate the evolution of turbulent jets issuing from realistic pipeline geometries. First, the effect of jet densities and Reynolds numbers on vertical jets were investigated, as they emerged from the side wall of a circular pipe, through a round orifice. The resulting jet flow was thus issued through a curved surface from a source whose original velocity components were nearly perpendicular to the direction of the ensuing jets. Particle image velocimetry (PIV) and planar laser-induced fluorescence (PLIF) techniques were employed simultaneously to provide instantaneous and time-averaged flow fields of velocity and concentration. The realistic flow arrangement resulted in an asymmetric flow pattern and a significant deflection from the vertical axis of jets. The deflection was influenced by buoyancy, where heavier gases deflected more than lighter gases. These realistic jets experienced faster velocity decay, and asymmetric jet spreading compared to round jets due to significant turbulent mixing in their near field.
In addition to that, horizontal multi-component jets issuing from a round orifice on the side wall of a circular tube were also investigated experimentally by the means of simultaneous velocity and concentration measurements. A range of Reynolds numbers and gas densities were considered to study the effects of buoyancy and asymmetry on the resulting flow structure. The realistic pipeline jets were always exhibited an asymmetry structure and found to deflect about the jet's streamwise axis in the near field. In the far field, the buoyancy dominated much closer to the orifice than expected in the axisymmetric round jet due to the realistic leak geometry along with the pipeline orientation considered in this study. In general, significant differences were found between the centreline trajectory, spreading rate, and velocity decay of conventional horizontal round axisymmetric jets issuing through flat plates and the pipeline leak-representative jets considered in the present study.
Finally, the dispersion of turbulent multi-component jets issuing from high-aspect-ratio slots on the side wall of a circular tube were studies experimentally by employing simultaneous PIV and PLIF techniques. Two transversal & longitudinal oblong geometries in respect to the longitudinal axes of the tube , and with an aspect ratio of 10 were considered in this study. Both horizontal and vertical orientations along with broad range of Reynolds numbers and gas densities were considered to investigate the effects of buoyancy and asymmetry on the resulting flow structure. The ensuing jets were found to deflect along the jet streamwise axis, once more, due to the realistic pipeline leak-representative configuration. It was also found that increases in aspect ratio of these realistic jets caused a reduction in the angle of deflection, jet centreline decay rates and the width growth on both velocity and scalar fields compared to their round jets counterparts, most notably in the far field.
These findings indicate that conventional jets (those that are issuing through flat surfaces) assumptions are inadequate to predict gas concentration, entrainment rates and, consequently, the extent of the flammability envelope of realistic gas leaks. Thus, extreme caution is required when using conventional jet assumptions to describe the physics of a buoyant jet emitted from realistic geometries. / Graduate
|
23 |
Laser-based Diagnostics and Numerical Simulations of Syngas Combustion in a Trapped Vortex CombustorKrishna, S January 2015 (has links) (PDF)
Syngas consisting mainly of a mixture of carbon monoxide, hydrogen and other diluents, is an important fuel for power generation applications since it can be obtained from both biomass and coal gasification. Clean coal technologies require stable and efficient operation of syngas-fired gas turbines. The trapped vortex combustor (TVC) is a relatively new gas turbine combustor concept which shows tremendous potential in achieving stable combustion under wide operating conditions with low emissions. In the present work, combustion of low calorific value syngas in a TVC has been studied using in-situ laser diagnostic techniques and numerical modeling. Specifically, this work reports in-situ measurements of mixture fraction, OH radical concentration and velocity in a single cavity TVC, using state-of-the art laser diagnostic techniques such as Planar Laser-induced Fluorescence (PLIF) and Particle Image Velocimetry (PIV). Numerical simulations using the unsteady Reynolds-averaged Navier-Stokes (URANS) and Large Eddy Simulation (LES) approaches have also been carried out to complement the experimental measurements. The fuel-air momentum flux ratio (MFR), where the air momentum corresponds to that entering the cavity through a specially-incorporated flow guide vane, is used to characterize the mixing. Acetone PLIF experiments show that at high MFRs, the fuel-air mixing in the cavity is very minimal and is enhanced as the MFR reduces, due to a favourable vortex formation in the cavity, which is corroborated by PIV measurements. Reacting flow PIV measurements which differ substantially from the non-reacting cases primarily because of the gas expansion due to heat release show that the vortex is displaced from the centre of the cavity towards the guide vane. The MFR was hence identified as the controlling parameter for mixing in the cavity. Quantitative OH concentration contours showed that at higher MFRs 4.5, the fuel jet and the air jet stream are separated and a flame front is formed at the interface. As the MFR is lowered to 0.3, the fuel air mixing increases and a flame front is formed at the bottom and downstream edge of the cavity where a stratified charge is present. A flame stabilization mechanism has been proposed which accounts for the wide MFRs and premixing in the mainstream as well. LES simulations using a flamelet-based combustion model were conducted to predict mean OH radical concentration and velocity along with URANS simulations using a modified Eddy dissipation concept model. The LES predictions were observed to agree closely with experimental data, and were clearly superior to the URANS predictions as expected. Performance characteristics in the form of exhaust temperature pattern factor and pollutant emissions were also measured. The NOx emissions were found to be less than 2 ppm, CO emissions below 0.2% and HC emissions below 700 ppm across various conditions. Overall, the in-situ experimental data coupled with insight from simulations and the exhaust measurements have confirmed the advantages of using the TVC as a gas turbine combustor and provided guidelines for stable and efficient operation of the combustor with syngas fuel.
|
Page generated in 0.0941 seconds