Over 30% of the world's population does not have access to safe drinking water, and the need for clean water spans further than just for human consumption. Currently, we use freshwater for growing agriculture, raising livestock, generating power, sanitizing waste, mining resources, and fabricating consumer goods. With that being said, the world is beginning to feel pressure from the excessive freshwater withdrawal compared to the current freshwater supply. This water stress is causing a water crisis. Places including Australia, South Africa, and California in the United States, just to name a few, are beginning to run out of fresh water to support daily societal demands. This is a phenomenon that is indiscriminately observed in all ranges of economically and politically developed countries and environments. However, it is important to note that less politically and economically developed countries especially those in arid climates, experience higher water stress than countries without such qualities. With only 2.5% of the world's water being freshwater and 30% of it being accessible as either ground or surface water, freshwater is a scarce resource, especially with the growing population and society's demand for water. Since the remaining 97.5% of water is composed of either brackish or seawater (saline water sources), one way to overcome the water stress would be to convert saline water into freshwater. As a result, various desalination techniques have been developed in the last 80 years that employ either membrane technology or temperature alterations to desalinate either brackish or seawater. One of the fastest growing methods for producing freshwater is reverse osmosis. Reverse osmosis uses an externally applied pressure, in the form of a cross flow back pressure, to overcome the osmotic pressure produced by the saline gradient across a semi-permeable membrane. The semi permeable membrane commercially consists of an interfacially polymerized aromatic polyamide thin film composite with a polysulfone porous backing that allows water to pass through while barring the transport of salt ions. This research focuses on the development of sulfonated poly(arylene ether sulfone) derivatives with differing amounts of sulfonation and with the ions placed at different structural positions. Previously, such materials were tested as potential high performance fuel cell membranes, but they are also of interest as potential high performance water desalination membranes, specifically for reverse osmosis. Two different methods were used to synthesize the sulfonated polysulfone derivatives: direct polymerization and post-modification of a non-sulfonated active polysulfone. The polysulfones from direct polymerization incorporated specialty sulfonated monomers, which were stoichiometrically controlled during the polymerization. Sulfonated polysulfones that were synthesized from post sulfonation incorporated biphenol and hydroquinone monomer units randomly throughout the polysufone backbones. These units could be sulfonated selectively because of their activation towards electrophilic aromatic substitution with sulfuric acid. Each of the polymers were cast into films ranging between 20-100 microns in thickness and tested for water uptake, hydrated uniaxial tensile properties, crossflow water and salt transport properties, and for crosslinked samples, gel fractions. The water uptakes from all the polysulfones were tuned by the degree of sulfonation or disulfonation present in the polymer. This was either controlled via the presence of a sulfonated monomer or a monomer that was active toward electrophilic aromatic substitution after polycondensation of the polysulfone. All polymers exhibited increases in their water uptake as the degree of sulfonation increased. We also observed a decreasing trend in the hydrated mechanical properties of the films for all the high molecular weight linear polymers as the water uptake was increased. The directly polymerized sulfonated polysulfones were found to have high hydrated elastic moduli ranging between 400 and 1000 MPa, while the post sulfonated counterparts (with either hydroquinone or biphenol incorporated in their structures) exhibited elastic moduli ranging between 1000 and 1500 MPa. It is important to note that the structures of the polymers were slightly different from one another because of the technique used to synthesize them. Thus, the increases in hydrated moduli among polymers synthesized via different routes may have influences from differences in chemical structures. Some of the polymers with higher degrees of sulfonation were synthesized as amine terminated oligomers with varying controlled molecular weights. The two targeted molecular weights were 5 and 10 kDa. Those oligomers were then crosslinked with a tetra-functional epoxide agent. The increases in sulfonation allowed for increases in water uptake and in theory, the water throughput through the sulfonated polysulfone membrane. Decreases in hydrated mechanical performance of the crosslinked networks with increasing degrees of sulfonation were also observed, similar to their high molecular weight linear counterparts. The directly polymerized crosslinked networks had salt permeabilities that plateaued at 70% disulfonation for both the 5 and 10 kDa polymers. Thus, we expect disulfonation content greater than 70% would lead to higher water throughput without significant increases in salt transport. / Doctor of Philosophy / A worldwide shortage of freshwater is becoming more problematic by each passing day. The World Health Organization and the United Nation's World Water Assessment Program predict that by 2025, 50-66% of the world's population will be living in a water-stressed area. This includes any area that experiences higher clean water withdrawals than are available. This includes but is not limited to areas that are politically unstable, technologically disadvantaged, resource deficient, located in arid climates, and highly populated. To put this further into perspective, only 2.5% of the available water on earth is freshwater. Freshwater typically has low concentrations of dissolved salts that are safe for human consumption and use. Of the available freshwater, only 30% of it is actually accessible for use through either surface or groundwater reservoirs, making the amount of clean water available for usage already a scarce resource. On the other hand, 97.5% of the world's water is composed of saline water reservoirs in the form of brackish and seawater. Through harnessing, seawater and removing the excess dissolved salt ions, the salt water can be converted to freshwater. Two major methods have been developed to remove the dissolved ions from water through either membrane filtration or thermal phase changes. One of the fastest growing membrane filtration techniques used worldwide is reverse osmosis. Reverse osmosis refers to the use of applied pressure across a semipermeable membrane to desalinate saline water. The semipermeable membrane prevents the migration of salt ions through the membrane while allowing transport of water. This work has focused on developing new polymers that can increase the overall efficiency of water desalination. Different types of high performance sulfonated polysulfone derivative polymers were synthesized and used to make membranes that were subsequently tested for performance. Relationships between the polymer structure, process, and properties were quantified through different analytical techniques. This study showed how the properties of sulfonated polysulfone membranes may be manipulated depending on structural modifications and processing to increase both the material's water throughput and salt rejection.

This thesis research focused on the synthesis and characterization of disulfonated poly(arylene ether sulfone) hydrophilic-hydrophobic segmented and multiblock copolymers for application as proton exchange membranes (PEMs) in fuel cells or as reverse osmosis (RO) membranes for water desalination. The first objective was to demonstrate that synthesizing blocky copolymers using a one oligomer, two monomer segmented copolymerization afforded copolymers with similar properties to those which used a previous approach of coupling two preformed oligomers. A 4,4′-biphenol based hydrophilic block of disulfonated poly(arylene ether sulfone) oligomer of controlled number average molecular weight (Mn) with phenoxide reactive end groups was first synthesized and isolated. It was then reacted with a calculated amount of hydrophobic monomers, forming that block in-situ. Copolymer and membrane properties, such as intrinsic viscosity, tensile strength, water uptake, and proton conductivity, were consistent with those of multiblock copolymers synthesized via the oligomer-oligomer approach. The segmented polymerization technique was then used to synthesize a variety of other copolymers for PEM applications. The well known bisphenol phenolphthalein was explored as a comonomer for either the hydrophilic and hydrophobic blocks of the copolymer. Membrane properties were explored as a function of block length for both series of copolymers. Both series showed that as block length increases, proton conductivity increases across the entire range of relative humidity (30-100%), as does, water uptake. This was consistent with earlier research which showed that the water self-diffusion coefficient scaled with block length. Copolymers produced with phenolphthalein had higher tensile strength, but lower ultimate elongation than the 4,4′-biphenol based copolymers. Multiblock copolymers were also synthesized and characterized to assess their feasibility as RO membranes. A new series of multiblock copolymers was synthesized by coupling hydrophilic disulfonated poly(arylene ether sulfone) (BisAS100) oligomer with hydrophobic unsulfonated poly(arylene ether sulfone) (BisAS0) oligomer. Both oligomers were derived using 4,´-isopropylidenediphenol (Bis-A) as the bisphenol. Phenoxide-terminated BisAS100 was end-capped with decafluorobiphenyl and reacted at relatively low temperatures (~ 100 oC) with phenoxide-terminated BisAS0. Basic properties were characterized as a function of block length. The initial membrane characterization suggested these copolymers may be suitable candidates for reverse osmosis applications, and water and salt permeability testing should be conducted to determine desalination properties. The latter measurements are being conducted at the University of Texas, Austin and will be reported separately. / Ph. D.

Hydrophilic/hydrophobic block copolymers as proton exchange membranes (PEMs) has become an emerging area of research in recent years. Three series of hydrophilic/hydrophobic, fluorinated/sulfonated multiblock copolymers were synthesized and characterized in this thesis. These copolymers were obtained through moderate temperature (~100°C) coupling reactions, which minimize the ether-ether interchanges between hydrophobic and hydrophilic telechelic oligomers via a nucleophilic aromatic substitution mechanism. The hydrophilic blocks were based on the nucleophilic step polymerization of 3,3′-disulfonated, 4,4′-dichlorodiphenyl sulfone with an excess 4,4′-biphenol to afford phenoxide endgroups. The hydrophobic (fluorinated) blocks were largely based on decafluoro biphenyl (excess) and various bisphenols. The copolymers were obtained in high molecular weights and were solvent cast into tough membranes, which had nanophase separated hydrophilic and hydrophobic regions. The performance and structure-property relationships of these materials were studied and compared to random copolymer systems. NMR results supported that the multiblock sequence had been achieved. They displayed superior proton conductivity, due to the ionic proton conducting channels formed through the self-assembly of the sulfonated blocks. The nano-phase separated morphologies of the copolymer membranes were studied and confirmed by atomic force microscopy. Through control of a variety of parameters, including ion exchange capacity and sequence lengths, performances as high, or even higher than those of the state-of-the-art PEM, Nafion, were achieved. / Ph. D.

Poly(arylene ether sulfone)s (PAES) are important commercial polymers and have been extensively studied due to their excellent thermal and mechanical properties. However, some applications are still limited when good solvent resistance and low thermal expansion coefficient are required. There has been a continuous interest in developing new PAES based on new monomers or polymer modifications to obtain new properties or to enhance existing properties. In this dissertation, the synthesis, characterization and structure-property relationship of new 1,4-cyclohexylene ring containing PAESs were comprehensively studied. Different polymerization techniques were used to synthesize polymers with different segmental lengths. The monomer, 4,4'-[trans-1,4-cyclohexanebis(methylene)] bisphenol (CMB), was synthesized and fully characterized. Based on 4,4′-dihydroxy-p-terphenyl (DHTP), 4,4′-dihydroxybiphenyl (DHBP) and the CMB monomer, homopolymer and random copolymers of PAES were prepared with high molecular weights and high glass transition temperatures. Dynamic mechanical analysis (DMA) on these polymers showed multiple sub-Tg relaxations. A large increase in the ultimate elongation was obtained with the CMB and DHTP containing sample, which could be due to the strong sub-Tg relaxations observed from the DMA results. A series of four acid chloride monomers were synthesized and polymerized with phenol terminated PAES oligomers. Solution polymerization and pseudo-interfacial polymerization techniques were used to prepare both bisphenol-A (bis-A) based and DHBP based PAES oligomers. With the incorporation of the trans-1,4-cyclohexylene units, decreases in the glass transition temperatures were observed from both the bis-A based and the DHBP based polymers. However, melting transitions were only observed in the DHBP based trans-1,4-cyclohexylene containing PAESs. Crystallinity was confirmed by differential scanning calorimetry (DSC) and wide angle X-ray diffraction (WAXD). A mechanical property study of the high molecular weight trans-1,4-cyclohexylene containing polymer samples showed moderate ultimate elongation enhancements. A series of PAES-polyester multiblock copolymers were synthesized with both solution method and melt polymerization. In the solution method, phenol terminated PAES oligomers and the acid chloride terminated poly(1,4-cyclohexylenedimethylene terephthalate) (PCT) oligomers were presynthesized and coupled in solution. The molecular weights of the polymer products obtained from the solution method were limited by solubility issues. Melt phase polymerization was employed to obtain high molecular weight polymers. Hydroxy ethoxy terminated PAES oligomers were synthesized and polymerized with 1,4-cyclohexanedimethanol (CHDM) and dimethyl terephthalate (DMT) in the melt. Polymers with high molecular weights were obtained. Tensile test results suggested that the mechanical properties of these polymers were dominated by the PAES components with polyester contents up to 20 wt%. Melting transitions were observed from polymers with higher polyester contents, and these polymers exhibited limited solubility in common organic solvents. / Ph. D.

Poly(arylene ether sulfone)s with dendritic terminal groups were synthesized by step-growth polymerization of two difunctional monomers in the presence of preformed dendritic end-cappers. These polymers were characterized by NMR, SEC, DSC, TGA, melt rheology and tensile tests. The melt viscosities of these polymers in the high frequency region were lower than the control while the stress-strain properties were comparable to those of the control, suggesting that it is possible to reduce the high shear melt viscosities of this type of polymers without affecting the stress-strain properties by introducing bulky dendritic terminal groups. Poly(arylene ether sulfone)s with hyperbranched terminal groups were also synthesized. These polymers were synthesized by reacting fluoro-terminated poly(arylene ether sulfone) chains with an arylene ether ketone AB2 monomer. The terminal groups of these polymers were capped by tert-butylphenol. The results from NMR and SEC showed that multiple tert-butyl units were successfully introduced onto the polymer chains, suggesting that this synthetic method could be useful for introducing multiple functional groups onto the polymer chain ends in fewer synthetic steps than an analogous method using preformed dendritic end-cappers. It was also demonstrated that multiple sulfonated phenols were attached to the terminal groups of polysulfones by this method. A novel cyclohexyl-containing difunctional monomer was prepared and successfully incorporated into poly(arylene ether sulfone) backbones. These polymers were characterized by NMR, SEC, DSC, TGA, DMA and tensile tests and compared to terephthaloyl analogs. Tensile tests and DMA showed the cyclohexyl units impart a higher magnitude of secondary relaxation than the terephthaloyl units while maintaining high modulus, suggesting that these polymers may have higher impact strength than the ones with no cyclohexyl units. / Ph. D.