Universiẗat, Diss., 2002--Freiburg (Breisgau).

Regulatory T cells (Tregs) provide an essential tolerance mechanism to suppress the immune response. Under normal conditions, Tregs reduce reaction to self-antigens, and conversely, lack of Treg function leads to autoimmune diseases. Reengineering of the immune system with regards to Tregs, such as through adoptive immunotherapy, holds great therapeutic promise for treating a range of diseases. These approaches require production of Tregs, which can be induced from conventional, reactive T cells. This thesis is driven by the concept that changing the mechanical stiffness of biomaterials can be used to direct and optimize this induction process. It is known that T cells sense their extracellular environment, and that T cell activation can be modulated by mechanical cues. However, it is still unclear whether or not human Treg induction is sensitive to material stiffness. We studied this phenomenon by replacing the stiff plastic supports commonly used for T cell activation with planar, elastic substrates — specifically polyacrylamide (PA) gels and polydimethylsiloxane (PDMS) elastomer. Treg induction, as measured by expression of FOXP3, a master transcription factor, was sensitive to stiffness for both materials. Substrate stiffness also modulated the suppressive function and epigenetic profiles of these cells, demonstrating that substrate rigidity can direct Treg induction, complementing the use of chemical and genetic tools. Delving deeper into the mechanisms of T cell mechanosensing, single-cell transcriptomic analysis revealed that substrate rigidity modulates the trajectory of Treg induction from conventional T cells, altering a host of functions including metabolic profile. Together, these studies introduce the use of substrate stiffness and T cell mechanosensing towards directing and optimizing regulatory T cell production. Further development of cell culture systems around this discovery is critical for emerging T cell-based therapies, targeting cancer but also a broad range of diseases.

No / This paper presents a novel method to prepare stretchable conductors and pressure sensors based on the gold/polydimethylsiloxane (PDMS) system. The gold films were sputtered onto structured PDMS surfaces produced with a photolithographic surface treatment with the aim of reducing tensile strains in the gold film. Scanning electron microscopy (SEM) and atomic force microscopy analyses showed that these 3D patterns reduce cracks and delaminations in the gold film. Electrical measurements indicate that the patterns also protect the films against repeated tensile cycling, although the un-patterned samples remained conducting as well after the completion of 120 cycles. The extrapolated resistivity value of the patterned sample (4.5 × 10−5 Ωcm) compares well with previously published data. SEM micrographs indicate that the pattern features deflect the cracks and therefore toughen the gold film. However, x-ray photoelectron spectroscopy and contact angle analyses indicate that the patterning process also slightly modifies the surface chemistry. This patterning method was used to prepare capacitive strain gauges with pressure sensitivity (ΔZ/Z)/P of 0.14 kPa−1 in the sub-kPa regime. Such stretchable and potentially conformal low-pressure sensors have not been produced before and could prove advantageous for many smart fabric applications.

No description available.

No description available.

No description available.

This thesis addresses the systematic modification of poly(tetramethylene oxide) (PTMO), polyether based segmented thermoplastic polyurethane with a secondary aminoalkyl functional polydimethylsiloxane (PDMS), which was intended to improve the fire resistance of polyurethane systems. The PDMS oligomer was successfully incorporated into the polyurethane backbone via one step solution polymerization. The effect of PDMS content on thermal stability, morphology, surface composition, mechanical properties, and fire resistance of polyurethane was investigated. These polymers displayed a complex two phase morphology and composition-dependant mechanical properties. The PDMS segment microphase separated from other polyurethane segments and varying microphase separation morphologies were observed with differing PDMS content. Spherical dispersed complex phases and co-continuous phases occurred when the PDMS content was 15wt% and 55wt%, respectively. Similar thermal stability was observed for both the polyurethane control and the PDMS modified polyurethanes, but the later displayed increased char yield in air with increased PDMS concentration. Quantitative measurements of the fire resistance of the modified polyurethanes by cone calorimetry showed that the peak heat release rate of the 15wt% siloxane modified samples dropped 67wt%, compared with the polyurethane control. However, the peak heat release rate did not further change with increasing siloxane content. Excellent mechanical properties, in terms of tensile strength and elongation, were found for the modified polyurethane with 15wt% of PDMS. Higher PDMS levels did reduce tensile strength, probably because of the reduction in strain crystallizing PTMO content. The PDMS modification, which resulted in improved fire resistance and excellent mechanical properties, is attributed to the low surface energy of the PDMS segment that tended to migrate to the surface of the polymer. It could be oxidized into a partially silicate-like material upon heating in air. In addition, the syntheses of primary and secondary aminoalkyl functional PDMS based segmented polyureas are described herein. Two-phase morphology was observed for all the polyurea samples, even when the hard segment concentration was as low as 6wt%. All these polyureas formed clear transparent films that exhibited good mechanical properties even with very high PDMS content, up to 94wt%. They also demonstrated similar thermal stability, independent of the PDMS end group. However, the nature of the end group, i.e. primary or secondary aminoalkyl, had a dramatic effect on mechanical and morphological properties of these PDMS based polyureas, which was interpreted in terms of the level of hydrogen bonding. / Ph. D.

Poly(dimethylsiloxane-b-methylvinylsiloxane) (PDMS-b-PMVS) diblock copolymers were synthesized via anionic living polymerization with controlled molecular weights and narrow molecular weight distributions. Targeted molecular weights agreed well with experimental values determined by 1H NMR, 29Si NMR, and GPC. Morphologies were investigated by DSC to analyze glass transition temperatures. Only one Tg was observed for each PDMS-b-PMVS block copolymer suggesting that the blocks were miscible in bulk. Tg's ranged from approximately -126 to -128 °C and were between the Tg's of the PDMS (-123 °C) and PMVS (-137 °C) homopolymers. The PMVS blocks were functionalized with trimethoxysilethyl or triethoxysilethyl pendent groups via hydrosilations to yield poly(dimethylsiloxane-b-[poly(methylvinyl)-co-(methyl-(2-trimethoxysilethyl)siloxane)] (PDMS-b-[PMVS-co-PMTMS]) or poly(dimethylsiloxane-b-[poly(methylvinyl)-co-(methyl-(2-triethoxysilethyl)siloxane)] (PDMS-b-[PMVS-co-PMTES]) copolymers, respectively. The PMVS blocks were either derivatized with the functional groups or half of the repeat units were functionalized. The fully hydrosilated materials were diblock copolymers, and the materials that were 50% hydrosilated had a random sequence of methylvinylsiloxy units and methyl-(trialkoxysilethyl)siloxy units. The PDMS-b-[PMVS-co-PMTES] block copolymers had Tg's ranging from -124 to -126 °C and only one Tg was observed. Surface tension measurements suggested that PDMS-b-[PMVS-co-PMTES] copolymers formed aggregates in toluene. Stable suspensions of superparamagnetic cobalt nanoparticles were prepared in toluene in the presence of PDMS-b-[PMVS-co-PMTMS] or PDMS-b-[PMVS-co-PMTES] copolymers via thermolysis of Co2(CO)8. It is hypothesized that the block copolymers functioned as micellar templates for the cobalt nanoparticles. TEM micrographs showed non-aggregated cobalt nanoparticles coated with copolymers that had mean particle diameters ranging from ≥10-15 nm. Specific saturation magnetizations of these cobalt-copolymer complexes ranged from 90-110 emu g-1 Co, comparable to literature values for this particle size. / Master of Science

No / Gold on polydimethylsiloxane (PDMS) stretchable conductors were prepared using a novel approach by interlacing an hydrogenated amorphous carbon (a-C : H) layer between the deposited metal layer and the elastomer. AFM analysis of the a-C : H film surface before gold deposition shows nanoscale buckling, the corresponding increase in specific surface area corresponds to a strain compensation for the first 4–6% of bi-axial tensile loading. Without this interlayer, the deposited gold films show much smaller and uni-directional ripples as well as more cracks and delaminations. With a-C : H interlayer, the initial electrical resistivity of the metal film decreases markedly (280-fold decrease to 8 × 10−6 Ω cm). This is not due to conduction within the carbon interlayer; both a-C : H/PDMS and PDMS substrates are electrically insulating. Upon cyclic tensile loading, both films become more resistive, but return to their initial state after 20 tensile cycles up to 60% strain. Profiling experiments using secondary ion mass spectroscopy and x-ray photoelectron spectroscopy indicate that the a-C : H layer intermixes with the PDMS, resulting in a graded layer of decreasing stiffness. We believe that both this graded layer and the surface buckling contribute to the observed improvement in the electrical performance of these stretchable conductors.

The goal of this research is to cover a broad set of scientific investigations of elastomeric materials based on polydimethylsiloxane (PDMS) and poly((3,3,3-trifluoroethoxymethyl)methyloxetane) diol. The scope of study covers five areas, well correlated with each other. The first study investigates the near surface morphology of condensation cured PDMS as a function of increasing the amount of siliceous phase. The appearance, disappearance and reappearance of untreated fumed silica nanoparticles at the PDMS near surface and their correlation with the volume fraction of siliceous phase have been studied. This research with PDMS nanocomposites has led to the development of an alternative route for improving mechanical strength of PDMS elastomers, conventionally known to have weak mechanical properties. The second study involves synthesis of a triblock copolymer comprising of four mutually immiscible phases, namely, soft segments comprising of fluorous and silicone domains, a diisocyanate hard segment and a glassy siliceous phase. Structure-property relationship has been established with an investigation of the interesting surface and bulk morphology. The highly improved mechanical strength of these soft materials is noteworthy. The dominance of silicone soft block at the triblock near surface has led to the third study which investigates their potential non-adhesive or abhesive characteristic in both a laboratory scale and in a marine environment. The peak removal stress and the removal energy associated with the detachment of a rigid object from the surface of these triblock copolymers have been measured. Results obtained from laboratory scale experiments have been verified by static immersion tests performed in the marine environment, involving the removal of adhered soft and hard fouling organisms. Gaining insights on the characteristics of an easy release surface, namely low surface energy and a low near surface modulus, a new way for controlling the near surface composition for elastomeric coatings have been developed. This technique involves an elastomer end-capped with a siliceous crosslinking agent and a tough, linear polyurethane. The basic concept behind the hybrid compositions is to develop a coating suitable for foul release applications, having a low energy surface, low surface modulus but good bulk mechanical strength. Henceforth, the fourth study deals with synthesis and characterization of the hybrid polymers over a wide range of composition and investigates their foul release characteristic in laborartory scale experiments. In our final study, attempts have been made in generating a silicone coating with antimicrobial property. A quaternary alkylammonium in different weight percents have been incorporated into a conventional, condensation cured polydimethylsiloxane (PDMS) elastomer. Antimicrobial assay has been performed on these modified silicone coatings to assess their biocidal activity against strains of Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa. Surface accessibility of quaternary charges has been quantified by measuring the streaming potential of a modified coating. An effort has been made in improving the mechanical strength of the weak PDMS elastomers by adding treated fumed silica nanoparticles as reinforcements. The effect of adding fillers on the mechanical property (tensile), surface concentration of quaternary charge and on the biocidal activity of a representative sample has been investigated.