No description available.

Polymer photovoltaic systems whose photoactive layer is a blend of a semiconducting polymer with a fullerene derivative in a bulk heterojunction configuration are amongst the most successful organic photovoltaic devices nowadays. The three-dimensional organization in these layers (the morphology) plays a crucial role in the performance of the devices. Detailed characterization of this organization at the nanoscale would provide valuable information for improving future material and architectural design and for device optimization. In this thesis, the results of morphology studies of blends of several polyfluorene copolymers (APFOs) blended with a fullerene derivative are presented. Near-Edge X-ray Absorption Fine Structure (NEXAFS) spectroscopy was combined with dynamic Secondary Ion Mass Spectrometry (dSIMS) for surface and in-depth characterization of the blend films. NEXAFS was performed using two different electron detection methods, partial (PEY) and total (TEY) electron yield, which provide information from different depth regimes. Quantitative compositional information was obtained by fitting the spectra of the blend films with a linear combination of the spectra of films of the pure components. In blends of APFO3 with PCBM in two different blend ratios (1:1 and 1:4 of polymer:fullerene) NEXAFS data show the existence of compositional gradients in the vertical direction for both blend ratios, with clear polymer enrichment of the free surface. A series of APFOs with systematic changes in the side-chains was studied and it was shown that those small modifications can affect polymer:fullerene interaction and induce vertical phase separation. Polymer-enrichment of the free surface was clearly identified, in accordance with surface energy minimization mechanisms, and a compositional gradient was revealed already in the first few nanometers of the surface of the blend films. dSIMS showed that this vertical phase separation propagates throughout the film. It was possible to determine that as the polar character of the polymer increases, and thus the polymer:fullerene miscibility is improved, the tendency for vertical phase separation becomes stronger. / <p>Paper II was not published at the time of the licentiate defence and had the title: NEXAFS spectroscopy study of the surface composition in APFO3:PCBM blend films</p>

This research is to synthesize polyaniline (PANI) thin film on the Poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid) (PEDOT:PSS) by using potentiostatic deposition of electrochemical method. The hybrid film composed of PEDOT:PSS and PANI was fabricated to replace the ITO layer for polymer solar cells as an anode. In the future, the hybrid film can develop the flexible polymer solar cells. In this study, we fixed the total thickness of the hybrid film, and we investigated optical transmittance, conductivity, Highest Occupied Molecular Orbital (HOMO), surface roughness, and surface morphology of hybrid films by changing the ratio of PEDOT:PSS and PANI, and to discuss the factors on device efficiency. Then, we compared the device structures with anode made by PEDOT: PSS. We found the hybrid films fabricated with different ratio of PEDOT:PSS and PANI, and the HOMO results were similar. In addition, we found optical transmittance, conductivity, surface roughness, and surface morphology of hybrid films that varies with different ratio of PEDOT:PSS and PANI. The power conversion efficiencies of the device mainly were affected by the surface roughness and morphology of the hybrid film surface. Comparing to other parameters, the hybrid film fabricated by PEDOOT:PSS(280nm) and PANI(30nm) owns the most appropriate surface roughness and surface morphology. The power conversion efficiency(PCE) was up to 0.68%, and then via post-annealing of 90¢J 10 minutes the PCE was increase to 1.06% under AM 1.5G illumination based on PEDOT:PSS (280 nm) / PANI (30 nm) / P3HT: PCBM (100 nm) / Al (200 nm), and the device area of 0.16 cm2.

The investigation carried out in this project allowed for the development of eleven regioregular π-conjugated alternating copolymers and their implementation in organic solar cells. The eleven synthesized polymers, poly[(2,7-(9-(heptadecan-9-yl)-9H-carbazole))-alt-(4,7-dithien-2-yl-2,1,3-benzothiadiazole)] (CB), poly[(2,7-(9,9-dioctyl-9H-fluorene-2,7-diyl))-alt-(1,6-pyrene)] (LP), poly[(2,7-(9-(heptadecan-9-yl)-9H-carbazole))-alt-(5,5’’’-(3,3’’’-dihexyl-2,2':5',2'':5'',2'''-quarterthiophene))] (CT), poly[(2,7-(9-(heptadecan-9-yl)-9H-carbazole))-alt-(2,7-9H-fluoren-9-one)] (CF), poly[(2,7-(9-(heptadecan-9-yl)-9H-carbazole))-alt-(1,6-pyrene)] (CP), poly[(2,7-(9,9-dioctyl-9H-fluorene-2,7-diyl))-alt-(4,7-dithien-2-yl-2,1,3-benzothiadiazole)] (LB), poly[(2,7-(9,9-dioctyl-9H-fluorene-2,7-diyl))-alt-(2,7-9H-fluoren-9-one)] (LF), poly[(5,5’’’-(3,3’’’-dihexyl-2,2':5',2'':5'',2'''-quarterthiophene))-alt-(2,7-9H- fluoren-9-one)] (TF), poly[(2,7-(9,9-dioctyl-9H-fluorene-2,7-diyl))-alt-(4,4'-dioctyl-2,2'-bithiophene)] (oTLT), poly[(2,7-(9-(heptadecan-9-yl)-9H-carbazole))-alt-(4,4'-dioctyl-2,2'-bithiophene)] (oTCT), poly[(2,7-(9-(heptadecan-9-yl)-9H-carbazole))-alt-(4,4'-dihexyl-2,2'-bithiophene)] (TCT), were investigated using theoretical methods that included semi-empirical geometry optimizations, density functional theory (DFT) energy calculations, and time-dependent density functional theory (TD-DFT) optical absorption predictions. The absorption predictions gave credence to our experimental results in which the absorption of the longer polymer chains underwent a redshift from the monomer absorption. With several of the prepared polymers, bulk-heterojunction photovoltaic cells were fabricated and their photovoltaic activity was investigated. Several of the fabricated cells exhibited photovoltaic efficiencies including polymer/PCBM composites with an aluminum back electrode (CF, CT, P3HT, and MEH-PPV), and also inverted cells with a silver back electrode (CT, P3HT, and MEH-PPV). Several polymers (CF, CT, TCT, LP, oTCT, oTLT, P3HT, and MEH-PPV) were used to solubilize single-walled carbon nanotubes (SWNTs). The solubility of the nanotubes occurred by the polymers’ ability to wrap the tubes, disrupt the bundles (ropes of tubes), and allow for the creation of a homogeneous mixture. Polymer:PCBM:SWNT mixtures were prepared and utilized as the active layer in BHJ solar cells. Some of the inverted cells (with a silver back electrode) that incorporated the nanotube composites (CT, oTCT, oTLT, P3HT, and MEH-PPV) displayed photovoltaic activity. These preliminary results illuminate the photovoltaic behavior of the polymer and provide evidence for their future use in polymer solar cells. / Thesis (Master, Chemistry) -- Queen's University, 2011-02-13 22:09:00.464

This research is to synthesize polyaniline (PANI) thin film for polymer solar cells as a hole transport layer by using potentiostatic deposition of electrochemical method. In our previous studies, we have shown that the power conversion efficiencies of the solar cell device were improved for the slow polymerization rate. We choose the potentiostatic deposition method to improve the polymerization rate of PANI for the application in industry. In this study, we investigated optical transmittance, absorption spectrum, Highest Occupied Molecular Orbital (HOMO), surface roughness, and surface morphology of the PANI thin film by changing voltages and to discuss the factors on device efficiency. Then, we compared the device structures with hole transport layer PEDOT: PSS by spin-coating process. We found PANI thin films synthesized from different voltages, and the transmittance measurement results were similar. In addition, we found HOMO, surface roughness, and surface morphology of PANI thin film that varies with different voltages. The power conversion efficiencies of the device mainly were affected by the surface roughness and morphology of PANI thin film surface. Comparing to other parameters, PANI thin film polymerized at 0.8V owns the most appropriate surface roughness and surface morphology. The power conversion efficiency was up to 1.52% under AM 1.5G illumination based on ITO (150 nm) / PANI (75 nm) / P3HT: PCBM (100 nm) / Al (200 nm), and the device area of 0.16 cm2.

Optoelectronic characterisation techniques are assessed in their application to three solar cell systems. Charge injection barriers are found in PbS/ZnO colloidal quantum dot solar cells through the use of temperature dependent current-voltage and capacitance-voltage measurements. The injection barriers are shown to complicate the Mott-Schottky capacitance analysis which determines built-in bias and doping density. A model that incorporates depletion capacitance and a constant capacitance arising from the injection barriers is given to explain the Mott-Schottky plots. The junction mechanism at the PbS/ZnO interface is found to transition from excitonic to p-n behaviour based on the amount of UV photodoping the cell has received. External quantum efficiency analysis at different photodoping times reveals a growing charge collection region within the material, demonstrating the shift to p-n behaviour. This is further supported by the observance of depletion capacitance behaviour after, but not before, UV photodoping. Defects within GaAs cells containing InAs quantum dots are found to enhance the sub-bandgap performance of the cell using external quantum efficiency analysis. This is verified by illuminated current-voltage analysis using a 1000 nm high pass optical filter to block photons of larger energy than the bandgap. Using capacitance-voltage analysis, high temperature rapid thermal annealing is shown to induce defects in dilute nitride cells, which explains the drop in open circuit voltage compared to lower temperature annealed cells. The doping level of polymer solar cells exposed to air is found to increase with continued exposure using Mott-Schottky capacitance analysis. Current-voltage measurements show the formation of an Al2O3 barrier layer at the polymer/aluminium interface. The usefulness of capacitance-voltage measurements to probe the polymer/fullerene interface is investigated in thermally evaporated thiophene/C60 cells.

Density Functional Theory (DFT) and time-dependent Density Functional Theory (TD-DFT) are powerful tools for modeling orbital energy in conjugated molecules and have been useful tools for research in organic photovoltaics. In this work, DFT is first used to explain the red shift in the absorption spectrum and increased absorption observed in MEH-PPV. Initially, the modeling of the red-shift in the absorption peak of MEH-PPV is studied using Gaussian 03 software with the global hybrid functional B3LYP for exchange-correlation and the 6-31G basis set. DFT and TD-DFT are used to separately study the effects of polymer chain length, carbon-carbon double-bond stretching, and the polymer in solution vs. in gas space on red shift in absorption spectrum. Next, Gaussian 09 software and the same B3LYP functional and 6-31G basis set are used to study interchain and intrachain interactions of MEH-PPV in solution. The red shift in the absorption peaks for three MEH-PPV configurations (single-chain pentamer, two stacked pentamers, and decamer) are compared with experimental results for five different solvents (chloroform, toluene, xylene, dichloromethane, and chlorobenzene). This investigation indicates that inter-chain interactions dominate in “good” aromatic solvents as compared to “poor” non-aromatic solvents. The results suggest that inter-chain charge transfer interactions play a critical role in real solutions and inter-chain aggregation takes precedence over intra-chain aggregation in aromatic solvents. In the final section of the study, accurate values for the range-separation parameter (w) for three lengths of MEH-PPV polymer (trimer, tetramer, and pentamer) in five different solvents (chloroform, chlorobenzene, xylene, Tetrahydrofuran, and dichloromethane) are reported using the range-separated functionals wB97XD and CAM-B3LYP. Using these data, range separation parameters are predicted and used for longer polymer chains in chloroform solution. The differences in the range separation parameters for the different solvents is statistically significant and gives further insight into the polymer/solvent interaction.

The aim of this thesis is to achieve a deep understanding of the working mechanism of polymer based solar cells and to improve the device performance. Two types of the polymer based solar cells are studied here: all-polymer solar cells comprising macromolecular donors and acceptors based on poly(p-phenylene vinylene) and hybrid cells comprising a PPV copolymer in combination with a novel small molecule electron acceptor. To understand the interplay between morphology and photovoltaic properties in all-polymer devices, I compared the photocurrent characteristics and excited state properties of bilayer and blend devices with different nano-morphology, which was fine tuned by using solvents with different boiling points. The main conclusion from these complementary measurements was that the performance-limiting step is the field-dependent generation of free charge carriers, while bimolecular recombination and charge extraction do not compromise device performance. These findings imply that the proper design of the donor-acceptor heterojunction is of major importance towards the goal of high photovoltaic efficiencies. Regarding polymer-small molecular hybrid solar cells I combined the hole-transporting polymer M3EH-PPV with a novel Vinazene-based electron acceptor. This molecule can be either deposited from solution or by thermal evaporation, allowing for a large variety of layer architectures to be realized. I then demonstrated that the layer architecture has a large influence on the photovoltaic properties. Solar cells with very high fill factors of up to 57 % and an open circuit voltage of 1V could be achieved by realizing a sharp and well-defined donor-acceptor heterojunction. In the past, fill factors exceeding 50 % have only been observed for polymers in combination with soluble fullerene-derivatives or nanocrystalline inorganic semiconductors as the electron-accepting component. The finding that proper processing of polymer-vinazene devices leads to similar high values is a major step towards the design of efficient polymer-based solar cells. / Ziel dieser Dissertation ist es, die grundlegende Arbeitsweise von polymerbasierten Solarzellen zu verstehen und ihre Leistungsfähigkeit zu erhöhen. Zwei Arten von organischen Solarzellen werden untersucht: Solarzellen, bei denen sowohl Elektronendonator und akzeptor auf Poly(p-phenylen-vinylen) basieren sowie Zellen, bei denen ein PPV-Copolymer als Elektronendonator und organische kleine Moleküle als Elektronenakzeptor fungierten. Um die Zusammenhänge zwischen Morphologie und photovoltaischen Eigenschaften zu verstehen, untersuchte ich Photoströme sowie die Eigenschaften angeregter Zustände in Zweischicht- und Mischsolarzellen mit unterschiedlicher Nano-Morphologie, welche durch die Verwendung von Lösungsmitteln mit unterschiedlichen Siedetemperaturen modifiziert wurde. Die Hauptschlussfolgerung aus diesen Messungen ist, dass der effizienzlimitierende Faktor die feldabhängige Generation freier Ladungsträger ist, wohingegen bimolekulare Rekombination oder die Extraktion der Ladungsträger die Leistungsfähigkeit von Polymer-Polymer- Solarzellen nicht beeinträchtigen. Diese Ergebnisse legen nahe, dass die gezielte Einstellung der Donator-Akzeptor-Grenzfläche von besonderer Bedeutung zum Erreichen hoher Effizienzen ist. In Hybridsolarzellen aus Polymeren und kleinen Molekülen kombinierte ich das lochleitende konjugierte Polymer M3EH-PPV mit einem neuartigen Vinazen-Molekül als Elektronen-akzeptor. Dieses Molekül bietet die Möglichkeit, entweder aus einer Lösung heraus verarbeitet oder im Hochvakuum verdampft zu werden, wodurch eine Vielzahl an unterschiedlichen Probenstrukturen realisiert werden kann. Dadurch konnte ich zeigen, dass die Struktur der aktiven Schicht einen großen Einfluss auf die photovoltaischen Eigenschaften hat. Die Solarzellen erreichten einen Füllfaktor von bis zu 57% und eine Kurzschluss¬spannung von 1 V. In der Vergangenheit konnten bei polymerbasierten Solarzellen Füllfaktoren über 50% nur in Verbindung mit Fullerenen oder nanokristallinen anorganischen Halbleitern als Akzeptoren erreicht werden. Das Resultat, dass bei geeigneter Präparation der Polymer-Vinazen-Schicht vergleichbare Ergebnisse erzielt werden können, ist ein bedeutender Schritt hin zu effizienteren Polymersolarzellen.

Organic materials, such as conjugated polymers, have emerged as a promising alternative for the production of inexpensive and flexible photovoltaic cells. As conjugated polymers are soluble, liquid based printing techniques enable production on large scale to a price much lower than that for inorganic based solar cells. Present day state of the art conjugated polymer photovoltaic cells are comprised by blends of a semiconducting polymer and a soluble derivative of fullerene molecules. Such bulk heterojunction solar cells now show power conversion efficiencies of up to 4-6%. The quantum efficiency of thin film organic solar cells is however still limited by several processes, of which the most prominent limitations are the comparatively low mobility and the high level of charge recombination. Hence organic cells do not yet perform as well as their more expensive inorganic counterparts. In order to overcome this present drawback of conjugated polymer photovoltaics, efforts are continuously devoted to developing materials or devices with increased absorption or with better charge carrier transporting properties. The latter can be facilitated by increasing the mobility of the pure material or by introducing beneficial morphology to prevent carrier recombination. Minimizing the active layer film thickness is an alternative route to collect more of the generated free charge carriers. However, a minimum film thickness is always required for sufficient photon absorption. A further limitation for low cost large scale production has been the dependence on expensive transparent electrodes such as indium tin oxide. The development of cheaper electrodes compatible with fast processing is therefore of high importance. The primary aim of this work has been to increase the absorption in solar cells made from thin films of organic materials. Device construction, deploying new geometries, and evaluation of different methods to provide for light trapping and photon recycling have been strived for. Different routes to construct and incorporate light trapping structures that enable higher photon absorption in a thinner film are presented. By recycling the reflected photons and enhancing the optical path length within a thinner cell, the absorption rate, as well as the collection of more charge carriers, is provided for. Attempts have been performed by utilizing a range of different structures with feature sizes ranging from nanometers up to centimeters. Surface plasmons, Lambertian scatterers, micro lenses, tandem cells as well as larger folded cell structures have been evaluated. Naturally, some of these methods have turned out to be more successful than others. From this work it can nevertheless be concluded that proper light trapping, in thin films of organic materials for photovoltaic energy conversion, is a technique capable of improving the cell performance. In addition to the study of light trapping, two new alternative electrodes for polymer photovoltaic devices are suggested and evaluated.

With power conversion efficiency surpassing the 10% milestone for commercialization, photovoltaic technology based on solution-processable polymer solar cells (PSCs) provides a promising route towards a cost-efficient strategy to address the ever-increasing worldwide energy demands. However, to make PSCs successful, challenges such as insufficient light absorption, high maintenance costs, and relatively high production costs must be addressed. As solutions to some of these problems, the unique properties of nanostructured materials and complimentary light absorption in multi-junction device structure could prove to be highly beneficial. As a starting point, integrating nanostructure-based transparent self-cleaning surfaces in PSCs was investigated first. By controlling the length of the hydrothermally grown ZnO nanorods and covering their surface with a thin layer of chemical vapor-deposited SiO2, a highly transparent and UV-resistant superhydrophobic surface was constructed. Integrating the transparent superhydrophobic surface in a PSC shows minimal impact on the figure of merit of the PSC. To address the low mechanical durability of the transparent superhydrophobic surface based on SiO2-coated ZnO nanorods, a novel method inspired by the water condensation process was developed. This method involved directly growing hollow silica half-nanospheres on the substrate through the condensation of water in the presence of a silica precursor. Benefit from the decreased back scattering efficiency and increased light transport mean free path arise from the hollow nature, a transparent superhydrophobic surface was realized using submicrometer sized silica half-nanospheres. The decent mechanical property of silica and the “direct-grown” protocol are expected to impart improved mechanical durability to the transparent superhydrophobic surface. Regarding the application of multi-junction device structure in PSCs, homo multi-junction PSCs were constructed from an identical polymer absorber, in which the homo-tandem device showed an enhanced power conversion efficiency (PCE) (8.3% vs 7.7%) relative to the optimized single junction PSC. The high open voltage (>1.8 V) achieved in homo-tandem PSCs allowed for water splitting with an estimated solar-to-fuel conversion efficiency of 6%. Lastly, a hybrid tandem cell was also constructed using a polymer and a colloidal quantum dot subcell. Different hybrid tandem device architectures were proposed and show a promising PCE of 6.7%.