Spelling suggestions: "subject:"power factor correction."" "subject:"lower factor correction.""
31 |
Single-Stage High-Power-Factor Electronic Ballast with Class E Inverter for Fluorescent LampsHuang, Shih-Hung 11 June 2002 (has links)
A single-stage high-power-factor electronic ballast with class E inverter is proposed for driving the fluorescent lamp. The circuit configuration is obtained from the integration of a buck-boost converter for power-factor- correction (PFC) and a class E resonant inverter for ballasting. The integrated ballast circuit requires only one active power switch and simple control. Operating the buck-boost converter in discontinuous conduction mode (DCM) at a fixed frequency, the electronic ballast can achieve nearly unity power factor. With pulse-width-modulation (PWM), the electronic ballast can provide an appropriate filament current for preheating, a high voltage for ignition, and then a desired lamp current for steady-state operation. An additional control circuit is included to eliminate the glow current during preheating stage.
The operation of the ballast-lamp circuit is analyzed by fundamental approximation. Computer simulations are made and design equations are derived on basis of the power-dependent resistance model of the fluorescent lamp. With carefully designed circuit parameters, the active power switch can be switched on at zero current to reduce the switching losses leading to a higher efficiency.
An experimental circuit designed for a PL-27W compact fluorescent lamp is built and tested to verify the computer simulations and analytical predictions. Experimental results show that satisfactory performances can be obtained on the proposed electronic ballast.
|
32 |
Metodologia de projeto de conversores boost para correção de fator de potência apliocada a sistemas ininterruptos de energia / A design methodology for boost converters to power factor correction applied in uninterrruptible power suppliesDamasceno, Daniel da Motta Souto 20 April 2006 (has links)
This Master Thesis presents a design methodology to a boost PFC converter operating as an Uninterruptible Power Supply rectifier input stage. This methodology defines, making use of a group of current ripples and switching frequencies, the converter minimum volume point analyzing the volumes of the boost inductor, the electromagnetic interference filter and the heat-sinks. Thus, it's developed along this work, each design mentioned above, analyzing the impact of different magnetic materiaIs, input filter topologies and semiconductors technologies. Previously, it is designed the controller and it is developed a simulation structure. ln a second moment, it's designed the boost inductor for a predetermined temperature elevation. After this, it's designed the electromagnetic filter analyzing the impact of different topologies. The heat-sinks are also designed to guarantee the semiconductors operation within the temperature limits. Finally, the methodology based on the previous designs is accomplished, using the procedures and equations already mentioned, becoming possible to define the converter minimum volume point. / Esta Dissertação de Mestrado apresenta uma metodologia de projeto para o conversor boost operando como estágio retificador de entrada em uma fonte de alimentação
ininterrupta. Essa metodologia se baseia em definir, através de um conjunto de freqüências de comutação e ondulações de corrente, o ponto de minimização do volume do conversor considerando o volume do indutor, do filtro de interferência eletromagnética conduzida e dos dissipadores. Assim, é desenvolvido ao longo desse trabalho o projeto de cada elemento mencionado estudando o impacto do uso de diferentes materiais magnéticos, topologias de filtro de entrada e tecnologias de semicondutores. Inicialmente é projetado o controlador e desenvolvida a estrutura de simulação do conversor. Em um segundo momento é projetado o indutor boost para uma determinada elevação de temperatura. A seguir é projetado o filtro de interferência eletromagnética analisando o impacto de diferentes topologias. Também são projetados os dissipadores que garantem a operação dos semicondutores dentro dos limites de temperatura estabelecidos pelos fabricantes. Por fim, é formalizada a metodologia baseada nos projetos anteriores, pela qual, fazendo uso dos procedimentos e equações fornecidos, torna-se possível definir o ponto de minimização do volume do conversor.
|
33 |
Advanced high frequency switched-mode power supply techniques and applicationsNuttall, Daniel Robert January 2011 (has links)
This Thesis examines the operation and dynamic performance of a single-stage, single-switch power factor corrector, S4 PFC, with an integrated magnetic device, IM. Also detailed isthe development and analysis of a high power light emitting diode, HP LED, power factorcorrection converter and proposed voltage regulation band control approach.The S4 PFC consists of a cascaded discontinuous current mode, DCM, boost stage anda continuous current mode, CCM, forward converter. The S4 PFC achieves a high powerfactor, low input current harmonics and a regulated voltage output, utilising a singleMOSFET. A steady-state analysis of the S4 PFC with the IM is performed, identifying theoperating boundary conditions for the DCM power factor correction stage and the CCMoutput voltage regulation stage. Integrated magnetic analysis focuses on understanding theperformance, operation and generated flux paths within the IM core, ensuring the device doesnot affect the normal operation of the converter power stage. A design method for the S4 PFCwith IM component is developed along with a cost analysis of this approach. Analysis predictsthe performance of the S4 PFC and the IM, and the theoretical work is validated by MATLABand SABER simulations and measurements of a 180 W prototype converter.It is not only the development of new topological approaches that drives theadvancement of power electronic techniques. The recent emergence of HP LEDs has led to aflurry of new application areas for these devices. A DCM buck-boost converter performs thepower factor correction and energy storage, and a cascaded boundary conduction current modebuck converter regulates the current through the LED arrays. To match the useful operatinglifetime of the HP LEDs, electrolytic capacitors are not used in the PFC converter. Analysisexamines the operation and dynamic characteristics of a PFC converter with low capacitiveenergy storage capacity and its implications on the control method. A modified regulationband control approach is proposed to ensure a high power factor, low input current harmonicsand output voltage regulation of the PFC stage. Small signal analysis describes the dynamicperformance of the PFC converter, Circle Criterion is used to determine the loop stability.Theoretical work is validated by SABER and MATLAB simulations and measurements of a180 W prototype street luminaire.
|
34 |
Accurate Estimation of Core Losses for PFC InductorsJanuary 2019 (has links)
abstract: As the world becomes more electronic, power electronics designers have continuously designed more efficient converters. However, with the rising number of nonlinear loads (i.e. electronics) attached to the grid, power quality concerns, and emerging legislation, converters that intake alternating current (AC) and output direct current (DC) known as rectifiers are increasingly implementing power factor correction (PFC) by controlling the input current. For a properly designed PFC-stage inductor, the major design goals include exceeding minimum inductance, remaining below the saturation flux density, high power density, and high efficiency. In meeting these goals, loss calculation is critical in evaluating designs. This input current from PFC circuitry leads to a DC bias through the filter inductor that makes accurate core loss estimation exceedingly difficult as most modern loss estimation techniques neglect the effects of a DC bias. This thesis explores prior loss estimation and design methods, investigates finite element analysis (FEA) design tools, and builds a magnetics test bed setup to empirically determine a magnetic core’s loss under any electrical excitation. In the end, the magnetics test bed hardware results are compared and future work needed to improve the test bed is outlined. / Dissertation/Thesis / Masters Thesis Electrical Engineering 2019
|
35 |
Analysis and implementation of ripple current cancellation technique for electronic ballastsMarita, Marius G. January 2005 (has links)
No description available.
|
36 |
Performance Improvement of Power Conversion by Utilizing Coupled InductorsZhao, Qun 27 March 2003 (has links)
This dissertation presents the derivation, analysis and application issues of advanced topologies with coupled inductors. The proposed innovative solutions can achieve significant performance improvement compared to the state-of-the-art technology.
New applications call for high-efficiency high step-up DC-DC converters. The basic topologies suffer from extreme duty ratios and severe rectifier reverse recovery. Utilizing coupled inductor is a simple solution to avoid extreme duty ratios, but the leakage inductance associated with the coupled inductor induces severe voltage stress and loss. An innovative solution is proposed featuring with efficient leakage energy recovery and alleviated rectifier reverse recovery. Impressive efficiency improvement is achieved with a simple topology structure. The coupled inductor switching cell is identified. Topology variations and evaluations are also addressed.
The concept that utilizes coupled inductors to alleviate rectifier reverse recovery is then extended, and new topologies suitable for other applications are generated. The proposed concept is demonstrated to solve the severe rectifier reverse recovery that occurs in continuous current mode (CCM) boost converters. Significant profile reduction and power density improvement can be achieved in front-end CCM power factor correction (PFC) boost converters, which are the overwhelmingly choice for use in telecommunications and server applications.
This dissertation also proposes topologies to realize the single-stage parallel PFC by utilizing coupled inductors. Compared to the state-of-the-art single-stage PFC converters, the proposed topologies introduce a new power flow pattern that minimizes the bulk-capacitor voltage stress and the switch current stress. / Ph. D.
|
37 |
Three Dimensional Passive Integrated Electronic Ballast for Low Wattage HID LampsJiang, Yan 03 April 2009 (has links)
Around 19% of global power consumption and around 3% of global oil demand is attributable to lighting. After the first incandescent lamp was invented in 1879, more and more energy efficient lighting devices, such as gas discharge lamps, and light-emitting diodes (LED), have been developed during the last century. It is estimated that over 38% of future global lighting energy demand could be avoided by the use of more efficient lamps and ballasts [1].
High intensity discharge (HID) lamps, one category of gas discharge lamp, have been widely used in both commercial and residential lighting applications due to their merits of high efficacy, long life, compact size and good color rendition [2-4]. However, HID lamps require a well-designed ballast to stabilize the negative VI characteristics. A so-called ignitor is also needed to provide high voltage to initiate the gas discharge. Stringent input harmonic current limits, such as the IEC 61000-3-2 Class C standard, are set for lighting applications. It is well-known that high-frequency electronic ballasts can greatly save energy, improve lamp performance, and reduce the ballast size and weight compared with the conventional magnetic ballast. However, a unique phenomenon called acoustic resonance could occur in HID lamps under high-frequency operation. A low-frequency square wave current driving scheme has proved to be the only effective method to avoid acoustic resonance in HID lamps. A typical electronic HID ballast consist of three stages: power factor correction (PFC), DC/DC power regulation and low-frequency DC/AC inverter. The ignitor is usually integrated in the inverter stage. The three-stage structure results in a large size and high cost, which unfortunately offsets the merit of the HID lamp, especially in low-wattage applications. In order to make HID lamps more attractive in low-wattage and indoor applications, it is critical to reduce the size, weight and cost of HID ballasts.
This dissertation is aimed at developing a compact HID with an ultra-compact ballast installed inside the lamp fixture. It is a similar concept to the compact fluorescent lamp (CFL), but it is much more challenging than the CFL. Two steps are explored to achieve high power density of the HID ballast.
The first step is to improve the system structure and circuit topology. Instead of a three-stage structure, a two-stage structure is proposed, which consists of a single-stage power factor correction (SSPFC) AC/DC front-end and an unregulated DC/AC inverter/ignitor stage. An SSPFC AC/DC converter is proposed as the front-end. A DCM non-isolated flyback PFC semi-stage and a DCM buck-boost DC/DC semi-stage share the semiconductor switch, driver and PWM controller, so that the component count and cost can be reduced. The proposed SSPFC AC/DC front-end converter can achieve a high power factor, low THD, low bulk capacitor voltage, and the desired power regulation with a simple control circuit. Because the number of high-frequency switches is reduced compared to that of state-of-the-art two-stage HID ballast topologies, the switching frequency can be increased without sacrificing high efficiency, so the passive component size can be reduced. The power density of the whole ballast is increased using this two-stage structure. It results in a 2.5 times power density (6 W/in3) improvement compared to the commercial product (2.4 W/in3).
The power density of the converter in discrete fashion usually suffers as a result of poor three-dimensional (3D) volume utilization due to a large component count and the different form factor of different components. In the second step, integration and packaging technologies are explored to further increase the power density. A 3D passive integrated HID ballast is proposed in this dissertation. All power passive components are designed in planar shape with a uniform form factor to fully utilize the three-dimensional space. In addition, electromagnetic integration technologies are applied to achieve structural, functional and processing integration to reduce component volume and labor cost. System partitioning, integration and packaging strategies, and implementation of major power passive integration, including an integrated EMI filter, and an integrated ignitor, will be discussed in the dissertation. The proposed integrated ballast is projected to double the power density of the discrete implementation.
By installing the HID ballast inside the lamp fixture, the ambient temperature for the ballast will be much higher than the conventional separately installed ballast, and combined with a reduced size, the thermal condition for the integrated ballast will be much more severe. A thermal simulation model of the integrated ballast is built in the IDEAS simulation tool, and appropriate thermal management methods are investigated using the IDEAS simulation model. Experimental verification of various thermal management methods is provided. Based on the thermal management study, a new integrated ballast with improved thermal design is proposed. / Ph. D.
|
38 |
Investigation on Interleaved Boost Converters and ApplicationsWang, Chuanyun 25 August 2009 (has links)
With the rapid evolving IT technologies, today, the power factor correction (PFC) design is facing many challenges, such as power scalability, high entire-load-range efficiency, and high power density. Power scalability is a very desirable and cost-effective approach in the PFC design in order to keep up with servers' growing power requirements. Higher power density can eventually reduce the converter cost and allows for accommodating more equipment in the existing infrastructures. Driven strongly by economic and environmental concerns, high entire-load-range efficiency is more and more required by various organizations and programs, such as the U.S. Energy Star, Climate Savers, and German Blue Angel. Today, the existing boost PFC is reaching its limitations to meet these challenges simultaneously. Using the cutting-edge semiconductor devices, further efficiency improvement at light load is still needed. There are limited approaches available for increasing the power density due to the large EMI filter and inductor size.
Interleaved multi-channel boost PFC is a promising candidate to meet those challenges, but the interleaved boost converter is a less explored area. On the other hand, the multi-channel interleaved buck converter for the VR application has been intensively studied and thoroughly explored. One basic approach of this study is trying to extend the existing knowledge and techniques obtained from multiphase buck converters to the multi-channel interleaved boost converters since there are similarities existed between the multi-phase buck and the multi-channel boost converters.
The existing studies about the interleaving impact on the EMI filter design are based on the time domain ripple cancellation effect. This approach is good enough for most of the filter designs. However, unlike the conventional filter designs, the EMI filter design is a specification related process. Both the EMI standard and the EMI measurement are based on the frequency domain spectrum. Limited by the existing analysis approaches, it is difficult to provide a clear picture about how exactly the multi-channel interleaving will impact the EMI filter design. The interleaving impact on the Common Mode (CM) noise also has not been studied in any existing literatures for the same reason. In this study, the frequency domain analysis method was adopted. With the double Fourier integral transformation, a closed-form expression of all the harmonics of the noise sources can be obtained. With all the detailed phase relationship of the switching frequency harmonics and all the side band harmonics, the multi-channel interleaving impact on both the differential mode (DM) and CM filter design can be clearly understood and summarized. According to the design curves provided, the EMI filter size can be effectively reduced by properly choosing the interleaving channel number and the switching frequency. The multi-channel interleaving impact on the output capacitor current ripple is also studied and summarized in this dissertation.
It should be pointed out that interleaving only reduces the total input and output current ripples; the inductor current in each channel still has large ripple if small inductance is used. Similar to the multi-phase buck converter, coupling inductors result in different equivalent inductances for input current ripple and inductor current ripple for boost converters. Keeping the inductor current ripple magnitude the same, inverse coupling inductors between the interleaved channels can reduce the inductor size. However, the DM filter size is increased due to larger input current. Based on the investigation on the total magnetic component weight, inverse coupling inductor can reduce the total magnetic component weight. The reduction is more pronounced for lower switching frequency design when the inductor size is dominating among the total magnetic components.
Based on the harmonic cancellation, and with all the detailed phase relationship of the switching frequency harmonics and all the side band harmonics, a novel phase angle control method is proposed to maximize the reduction of the EMI filter. For example, in a 2-channel interleaved PFC, just by changing the interleaving scheme to 90 degree phase shift, 39% total volume reduction of the EMI filter can be achieved. The proposed phase angle controlled multi-channel PFC is experimentally demonstrated and verified on a digital controlled 4-channel PFC. The phase angle control method proposed in the multi-channel boost converter can be applied back to the multi-phase buck converter as well. The harmonic cancellation principle will be the same as the multi-channel boost converter. The same benefits can be obtained when the requirement is defined in the frequency domain, e.g. the EMI Standard.
The interleaved multi-channel configuration makes it possible to implement the phase-shedding to improve the PFC light load efficiency. By decreasing the number of active channels according to the load, the PFC light load efficiency can be optimized. However, shedding phases can reduce the ripple cancellation effect as well, which will result in the EMI noise increase and losing the benefit on the EMI filter. By applying the proposed phase-shedding with phase angle control strategy, the phase shedding impact on the EMI filter design can be minimized. The light load efficiency can be improved without compromising the EMI filter size. Then, adaptive frequency controlled PFC is proposed to further improve the PFC light load efficiency. The proposed light load efficiency improvement strategies are combined and implemented on the platform of the digital controlled 4-channel PFC. The benefit of improving the light load efficiency is experimentally verified. The EMI performance is also evaluated with the EMI measurement results obtained from the PFC prototype.
Following the same approach explored, the benefits of interleaved boost converter can be further extended other applications, such as the boost converter in the Hybrid Electric Vehicles (HEV) and photovoltaic (PV) system. / Ph. D.
|
39 |
Conducted EMI Noise Prediction and Filter Design OptimizationWang, Zijian 04 October 2016 (has links)
Power factor correction (PFC) converter is a species of switching mode power supply (SMPS) which is widely used in offline frond-end converter for the distributed power systems to reduce the grid harmonic distortion. With the fast development of information technology and multi-media systems, high frequency PFC power supplies for servers, desktops, laptops and flat-panel TVs, etc. are required for more efficient power delivery within limited spaces. Therefore the critical conduction mode (CRM) PFC converter has been becoming more and more popular for these information technology applications due to its advantages in inherent zero-voltage soft switching (ZVS) and negligible diode reverse recovery. With the emerging of the high voltage GaN devices, the goal of achieving soft switching for high frequency PFC converters is the top priority and the trend of adopting the CRM PFC converter is becoming clearer.
However, there is the stringent electromagnetic interference (EMI) regulation worldwide. For the CRM PFC converter, there are several challenges on meeting the EMI standards. First, for the CRM PFC converter, the switching frequency is variable during the half line cycle and has very wide range dependent on the AC line RMS voltage and the load, which makes it unlike the traditional constant-frequency PFC converter and therefore the knowledge and experience of the EMI characteristics for the traditional constant-frequency PFC converter cannot be directly applied to the CRM PFC converter.
Second, for the CRM PFC converter, the switching frequency is also dependent on the inductance of the boost inductor. It means the EMI spectrum of the CRM PFC converter is tightly related the boost inductor selection during the design of the PFC power stage. Therefore, unlike the traditional constant-frequency PFC converter, the selection of the boost inductor is also part of the EMI filter design process and EMI filter optimization should begin at the same time when the power stage design starts.
Third, since the EMI filter optimization needs to begin before the proto-type of the CRM PFC converter is completed, the traditional EMI-measurement based EMI filter design will become much more complex and time-consuming if it is applied to the CRM PFC converter. Therefore, a new methodology must be developed to evaluate the EMI performance of the CRM PFC converter, help to simplify the process of the EMI filter design and achieve the EMI filter optimization.
To overcome these challenges, a novel mathematical analysis method for variable frequency PFC converter is thus proposed in this dissertation. Based on the mathematical analysis, the quasi-peak EMI noise, which is specifically required in most EMI regulation standards, is investigated and accurately predicted for the first time. A complete approximate model is derived to predict the quasi-peak DM EMI noise for the CRM PFC converter. Experiments are carried out to verify the validity of the prediction. Based on the DM EMI noise prediction, worst case analysis is carried out and the worst DM EMI noise case for all the input line and load conditions can be found to avoid the overdesign of the EMI filter. Based on the discovered worst case, criteria to ease the DM EMI filter design procedure of the CRM boost PFC are given for different boost inductor selection. Optimized design procedure of the EMI filter for the front-end converter is then discussed. Experiments are carried out to verify the validity of the whole methodology. / Ph. D.
|
40 |
Mobile Hybrid Power System Theory of OperationPierce, Timothy M. Jr. 08 August 2016 (has links)
Efficiency is a driving constraint for electrical power systems as global energy demands are ever increasing. Followed by the introduction of diesel generators, electricity has become available in more locations than ever. However, operating a diesel generator on its own is not the most energy efficient. This is because the high crest factor loads, of many applications, decrease the fuel efficiency of a hydrocarbon generator. To understand this, we need to understand how an electrical load affects a generator.
Starting with a load profile, a system designer must choose a generator to meet peak demand, marking the first instance where a load profile has influence over a generator. This decision will insure that brownouts do not occur, but, this will lead to poor energy efficiency. We say this because a generator is most energy efficient under heavier loads, meaning, during lighter loads, more fuel will be consumed to produce the same amount of energy.
While this may be fine if the peak load was close to the average load, however, the actual crest factor for a typical residential load profile is much higher. This gap between peak and average load means that a generator will spend most of its time operating at its most inefficient point. To compensate for this, and reduce fuel consumption, the Mechatronics Lab at Virginia Tech has developed a mobile hybrid power system (MHPS) to address this problem. The solution was to augment a diesel generator with a battery pack. This allowed us to constrain the generator so that it only operates with fixed efficiency. It is the theory behind this system that will be covered in this thesis. / Master of Science
|
Page generated in 0.1399 seconds