yes / The envelope correlation for a two-element antenna array may be calculated using the antenna radiation fields, or more simply from the scattering parameters of the system. The use of scattering parameters provides a major simplification over the direct use of field data. In this paper we propose a modification of the scattering parameter method which also includes the antenna losses. This approach has the advantage of simplifying the antenna design process, especially when low envelope correlations are needed. It also offers a better prediction of the spatial envelope correlation, and a good framework for understanding the effects of the mutual coupling. The accuracy of this proposed method is illustrated by two examples.

The aim of the work reported in this thesis is to establish a generic approach for the study of the propagation of higher-order modes in ducts of circular cross section when a simple aperture device is installed in the duct. Additionally to describe the effects of the simple aperture device on the whole in duct acoustic field, especially in the frequency range after the first higher-order mode cuts on. The approach, which is based on approximating each higher-order mode as an uncoupled mode, requires an accurate and effective decomposition of the in duct field in the higher frequency range. In the theoretical work for the propagation of the higher-order modes in circular ducts, one established model to describe the open end of the duct is considered. Another model to describe the sound source (both plane wave source and point source) and the boundaries between the aperture device and the main duct is proposed. Combining the two models together, a revised model to describe the whole acoustic system is obtained and used to carry out the in duct field decomposition in the higher frequency range. From this the amplitudes of various higher-order modes are obtained. Experimental investigations have also been carried out to determine the applicability of this model. The experimental work can be divided into two groups: reference measurements for the inputs to the models and direct measurements of the sound fields. The reference measurements are used to obtain the strength of the sound source. The direct measurements are used to compare with the results obtained from the theoretical calculations. Through the comparison, the errors and the applicability of the theoretical model are established. It is shown that this approach to the problem may be used in the normalized wave number region up to k * R -< 7 , which is nearly four times the plane wave region and includes sixteen propagating higher-order modes. By determining the amplitudes of the higher-order modes, the whole in-duct acoustic field is fully decomposed into individual model contributions and can be reconstructed in detail. In order to get a complete and coordinate-independent description of the effects of installing different simple aperture devices, the power radiated out of the open end of - i - the duct is calculated in the fonn of different single modes. Additionally the insertion losses for different aperture device situations are also obtained. Then through the comparison of the powers and the insertion losses, it is possible to find an effective and direct way to express the effects of installing different simple aperture devices in a duct.

Le travail présenté dans cette thèse a pour objectif l’étude des conditions nécessaires pour évaluer l'exposition radio fréquence (RF) due aux téléphones mobiles dans un scenario d’utilisation réelle et le développement d’une méthodologie permettant de prédire et de comparer les téléphones mobiles en fonction de leurs expositions RF réelles. Les téléphones mobiles sont caractérisés par leur débit d'absorption spécifique (DAS) et leur performance en émission et en réception (over-the-air, OTA). En utilisant le DAS et la puissance totale rayonnée (PTR), un indice d'exposition appelée l'indice SAROTA a été proposé précédemment afin de prévoir l'exposition réelle des téléphones mobiles. L’indice SAROTA sert ainsi de métrique permettant de comparer les téléphones mobiles. Afin de déterminer expérimentalement l’exposition réelle aux RF, plusieurs téléphones avec des modifications logicielles permettant d’enregistrer les paramètres du réseau, sont utilisés pour l’étude qui est menée comme suit : (a) caractérisation des outils et des ressources disponibles pour effectuer des mesures ciblées, (b) identification des ressources radio et des paramètres importants pour effectuer ces mesures, (c) étude de la mise en œuvre effective du mécanisme de contrôle de puissance observé dans un réseau mobile réel pour différents niveaux et de qualités du signal reçus, (d) étude de la corrélation entre la performance OTA des téléphones mobiles et l’étendue effective du contrôle de puissance appliquée par le réseau, (e) comparaison entre la valeur réelle de l’exposition et la valeur prédite en utilisant l’indice SAROTA. Comme les défis logistiques et techniques sont plus difficiles à surmonter pour les mesures dans un environnement multi-trajets extérieur, les expériences ont été limitées à des environnements intérieurs pour assurer une meilleure répétabilité des mesures. Lors d’une première phase de l’étude, la stabilité de l’environnement intérieur a été évaluée. Lors d’une deuxième phase, l’influence de la main sur le DAS et la PTR des téléphones mobiles ainsi que sur l’évaluation de l’exposition réelle prédite par l’indice SAROTA a été étudiée. Lors d’une troisième phase, un ensemble de téléphones mobiles identiques ont été modifiés et des mesures effectuées pour vérifier que l’indice SAROTA permet bien de prédire l’exposition réelle des personnes. / The work presented in the thesis is directed towards addressing the requirement for determining the radio frequency (RF) exposure due to mobile phones under typical usage/ real-life scenarios and also to develop a method to predict and compare mobile phones for their real-life RF exposure. The mobile phones are characterized for their specific absorption rate (SAR) and for transmit and receive performance given by the over-the-air (OTA) characterization. Using the SAR and the total radiated power (TRP) characterization, an exposure index referred to as the SAROTA index was previously proposed to predict the real-life exposure due to mobile phones which would also serve as a metric to compare individual phones. In order to experimentally determine the real-life RF exposure, various software modified phones (SMP) are utilized for the study. These phones contain an embedded software capable of recording the network parameters. The study is undertaken in the following order: (a) Characterization of the available tools and resources for performing targeted measurements/experiments, (b) identifying the important radio resource parameters and metrics to perform the targeted measurements, (c) investigation of the actual implementation of the power control mechanism in a live network for various received signal level and received quality environments, (d) investigating the correlation of the over-the-air performance of the mobile phones and the extent of actual power control realization, (e) comparing the actual exposure and the real-life exposure as predicted by the SAROTA index. Based on the logistical and technical challenges encountered, the experiments were restricted to indoor environments to enable repeatability. During the first phase of the study, the stability of the indoor environment was evaluated. During the second phase, the influence of hand phantom on the SAR and TRP of the mobile phones and the capability of the SAROTA index to predict the exposure was investigated. Further developing on the insights from the hand phantom experiments, in the third phase, a set of identical software modified phones were externally modified to alter the TRP performance and the methodology to determine the real-life exposure and also verify the capability of the SAROTA index to predict the exposure levels was investigated. The experiments demonstrate that the SAROTA index is capable of predicting the real-life exposure and comparing the mobile phones.

A procedure for computational dosimetry to verify safety standards compliance of mobile communications base stations is presented. Compared with the traditional power density method, a procedure based on more rigorous physics was devised, requiring computation or measurement of the specific absorption rate (SAR) within the biological tissue of a person at an arbitrary distance. This uses a hybrid methd of moments/finite difference time domain (MoM/FDTD) numerical method in order to determine the field or SAR distribution in complex penetrable media, without the computational penalties that would result from a wholly FDTD simulation. It is shown that the transmitted power allowed by the more precise SAR method is, in many cases, between two and five times greater than that allowed by standards implementing the power flux density method.

This work investigates the application of active noise control (ANC) to speech. ANC has had success reducing tonal noise. In this work, that success was extended to noise that is not completely tonal but has some tonal elements such as speech. Limitations such as causality were established on the active control of human speech. An optimal configuration for control actuators was developed for a sphere using a genetic algorithm. The optimal error sensor location was found from exploring the nulls associated with the magnitude of the radiated pressure with reference to the primary pressure field. Both numerically predicted and experimentally validated results for the attenuation of single frequency tones were shown. The differences between the numerically predicted results for attenuation with a sphere present in the pressure field and monopoles in the free-field are also discussed.The attenuation from ANC of both monotone and natural speech is shown and a discussion about the effect of causality on the results is given. The sentence “Joe took father’s shoe bench out” was used for both monotone and natural speech. Over this entire monotone speech sentence, the average attenuation was 8.6 dB with a peak attenuation of 10.6 dB for the syllable “Joe”. Natural speech attenuation was 1.1 dB for the sentence average with a peak attenuation on the syllable “bench” of 2.4 dB. In addition to the lower attenuation values for natural speech, the pressure level for the word “took” was increased by 2.3 dB. Also, the harmonic at 420 Hz in the word “father’s” of monotone speech was reduced globally up to 20 dB. Based on the results of the attenuation of monotone and natural speech, it was concluded that a reasonable amount of attenuation could be achieved on natural speech if its correlation could approach that of monotone speech.