The performance of commercial Radio Frequency Identification (RFID) tags is primarily limited by present techniques used for tag antenna design. Currently, industry techniques rely on identifying the RFID tag application (books, clothing, etc.) and then building antenna prototypes of different configurations in order to satisfy minimum read range requirements. However, these techniques inherently lack an electromagnetic basis and are unable to provide a low cost solution to the tag antenna design process. RFID tag performance characteristics (read-range, chip-antenna impedance matching, surrounding environment) can be very complex, and a thorough understanding of the RFID tag antenna design may be gained through an electromagnetic approach in order to reduce the tag antenna size and the overall cost of the RFID system. The research presented in this thesis addresses RFID tag antenna design process for passive RFID tags. With the growing number of applications (inventory, supply-chain, pharmaceuticals, etc), the proposed RFID antenna design process demonstrates procedures to design tag antennas for such applications. Electrical/geometrical properties of the antennas designed were investigated with the help of computer electromagnetic simulations in order to achieve optimal tag performance criteria such as read range, chip-impedance matching, antenna efficiency, etc. Experimental results were performed on the proposed antenna designs to compliment computer simulations and analytical modelling.

Radio frequency identification (RFID) is a versatile wireless technology usedworldwide. The fields of applications are many and its popularity constantlygrows due to smaller in size, better and less expensive components. RFID isused to identify, track or share information about an object using radio waves. This master thesis describes the process of designing and implementing ahandheld UHF RFID reader. The goal was to, based on a UHF RFID-chipdesign a fully functional, small in size and power efficient device. Amicrocontroller provides the user interface and is also used to control theRFID-chip and a Bluetooth device. A Bluetooth- and GPRS-compatible mobilephone will be used to forward data to a server connected to the Internet. Allparts of the design are described, such as the printed circuit board design aswell as the software for the micro controller and the mobile phone. Because the extent of this thesis it is neither possible nor necessary to dig toodeep into the Bluetooth- or GPRS-protocol. The focus will be on designingsoftware and hardware for the handheld unit. / Radio frekvens identifiering (RFID) är en mångsidig trådlös teknik somanvänds över hela världen. Områdena där tekniken används är många och dess popularitet växer konstant tack vare mindre storlek, bättre och billigarekomponenter. RFID används för att identifiera, spåra eller dela med siginformation om ett objekt med radiovågor. Det här examensarbetet beskriver processen av design och implementering aven handburen UHF RFID läsare. Målet har varit att, baserat på ett UHF-RFIDchip, designa en fullt fungerande, liten och strömsnål enhet. En microcontroller förser dels användaren med ett användargränssnitt och sköter delskommunikationen med RFID chip och en blåtandsmodul. En blåtands- ochGPRS- eller 3G-kompatibel mobiltelefon används for att skicka vidare data tillen server kopplad till Internet. Alla delar av designen är beskrivna, så som PCB design, mjukvara för micro controllern och mobiltelefonen. På grund av omfattningen av det här examensarbetet så har det inte varitmöjligt eller nödvändigt att gräva för djupt i Blåtands- eller GPRS/3Gprotokollen. Fokus är på att designa hårdvara och mjukvara för den handhållna enheten.

Fundamental features of Radio Frequency Identification (RFID) systems used in different application areas will be reviewed. Techniques used in realizing RFID antenna systems will be studied and the procedure to realize a specific RFID antenna type possessing desired characteristics will be described. Electrical properties such as radiation pattern, impedance will be predicted using analytical and/or computer simulation techniques. Experimental investigations will be carried out to complement the theoretical work.

<p>Radio frequency identification (RFID) is a versatile wireless technology usedworldwide. The fields of applications are many and its popularity constantlygrows due to smaller in size, better and less expensive components. RFID isused to identify, track or share information about an object using radio waves.</p><p>This master thesis describes the process of designing and implementing ahandheld UHF RFID reader. The goal was to, based on a UHF RFID-chipdesign a fully functional, small in size and power efficient device. Amicrocontroller provides the user interface and is also used to control theRFID-chip and a Bluetooth device. A Bluetooth- and GPRS-compatible mobilephone will be used to forward data to a server connected to the Internet. Allparts of the design are described, such as the printed circuit board design aswell as the software for the micro controller and the mobile phone.</p><p>Because the extent of this thesis it is neither possible nor necessary to dig toodeep into the Bluetooth- or GPRS-protocol. The focus will be on designingsoftware and hardware for the handheld unit.</p> / <p>Radio frekvens identifiering (RFID) är en mångsidig trådlös teknik somanvänds över hela världen. Områdena där tekniken används är många och dess popularitet växer konstant tack vare mindre storlek, bättre och billigarekomponenter. RFID används för att identifiera, spåra eller dela med siginformation om ett objekt med radiovågor.</p><p>Det här examensarbetet beskriver processen av design och implementering aven handburen UHF RFID läsare. Målet har varit att, baserat på ett UHF-RFIDchip, designa en fullt fungerande, liten och strömsnål enhet. En microcontroller förser dels användaren med ett användargränssnitt och sköter delskommunikationen med RFID chip och en blåtandsmodul. En blåtands- ochGPRS- eller 3G-kompatibel mobiltelefon används for att skicka vidare data tillen server kopplad till Internet. Alla delar av designen är beskrivna, så som PCB design, mjukvara för micro controllern och mobiltelefonen.</p><p>På grund av omfattningen av det här examensarbetet så har det inte varitmöjligt eller nödvändigt att gräva för djupt i Blåtands- eller GPRS/3Gprotokollen. Fokus är på att designa hårdvara och mjukvara för den handhållna enheten.</p>

The performance of commercial Radio Frequency Identification (RFID) tags is primarily limited by present techniques used for tag antenna design. Currently, industry techniques rely on identifying the RFID tag application (books, clothing, etc.) and then building antenna prototypes of different configurations in order to satisfy minimum read range requirements. However, these techniques inherently lack an electromagnetic basis and are unable to provide a low cost solution to the tag antenna design process. RFID tag performance characteristics (read-range, chip-antenna impedance matching, surrounding environment) can be very complex, and a thorough understanding of the RFID tag antenna design may be gained through an electromagnetic approach in order to reduce the tag antenna size and the overall cost of the RFID system. The research presented in this thesis addresses RFID tag antenna design process for passive RFID tags. With the growing number of applications (inventory, supply-chain, pharmaceuticals, etc), the proposed RFID antenna design process demonstrates procedures to design tag antennas for such applications. Electrical/geometrical properties of the antennas designed were investigated with the help of computer electromagnetic simulations in order to achieve optimal tag performance criteria such as read range, chip-impedance matching, antenna efficiency, etc. Experimental results were performed on the proposed antenna designs to compliment computer simulations and analytical modelling.

A wide range of services and applications become possible when accurate position information for a radio terminal is available. These include: location-based services; navigation; safety and security applications. The commercial, industrial and military value of radio-location is such that considerable research effort has been directed towards developing related technologies, using satellite, cellular or local area network infrastructures or stand-alone equipment. This work studies and investigates two location techniques. The first one presents an implementation scheme for a wideband transmission and direction finding system using OFDM multi-carrier communications systems. This approach takes advantage of delay discrimination to improve angle-of-arrival estimation in a multipath channel with high levels of additive white Gaussian noise. A new methodology is interpreted over the multi carrier modulation scheme in which the simulation results of the estimated channel improves the performance of OFDM signal by mitigating the effect of frequency offset synchronization to give error-free data at the receiver, good angle of arrival accuracy and improved SNR performance. The full system simulation to explore optimum values such as channel estimation and AoA including the antenna array model and prove the operational performance of the OFDM system as implemented in MATLAB. The second technique proposes a low cost-effective method of tracking and monitoring objects (examples: patient, device, medicine, document) by employing passive radio frequency identification (RFID) systems. A multi-tag, (totalling fifty-six tags) with known ID values are attached to the whole patient’s body to achieve better tracking and monitoring precision and higher accuracy. Several tests with different positions and movements are implemented on six patients. The aim is to be able to track the patient if he/she is walking or sitting; therefore, the tests considered six possible movements for the patient including walking, standing, sitting, resting, laying on the floor and laying on the bed, these placements are important to monitor the status of the patient like if he collapsed and fall on the ground so that the help will be quick. The collected data from the RFID Reader in terms of Time Stamp, RSS, Tag ID, and a number of channels are processed using the MATLAB code.