Approved for public release; distribution is unlimited / The radio channel places fundamental limitations on the performance of mobile ad hoc wireless networks. In the mobile radio environment, fading due to multipath delay spread impairs received signals. The purpose of this thesis is to develop a radio channel model and examine the effect of various parameters on channel behavior that is representative of environments in which mobile ad hoc wireless networks operate. The various physical phenomena considered are outdoor environments, fading and multipath propagation, type of terrains, and mobility (Doppler shift). A channel model based on a Tapped Delay Line (TDL) structure was developed and implemented in the MATLAB programming language, and the performance of the time-varying channel was studied by plotting the signal constellations. The simulation results indicate that the number of taps required in the TDL is 8 or less and the carrier frequency did not influence the performance significantly. The Jakes Doppler spectrum should be used in urban environments with high mobility; the Gaussian Doppler spectrum is the choice for low mobility urban environments and for the hilly terrain under both low and high mobility. / Civilian, Singapore Ministry of Defense

Master’s thesis is focused on part of mobile network named LTE. Project is analyzes the LTE physical layer, which is divided into four basic parts: Physical channels and modulation, Multiplexing and channel coding, Physical layer procedures, Physical layer measurements. Every part is described by actual 3GPP standard [1]. To understand the problem is expected a reader basic knowledge of OFDM systems, which the LTE system uses. The next part of this master’s thesis is dedicated to mathematic model physical layer of system LTE, created by program Matlab. This model is designed to measure errors in data transmission.

As the demand for wireless communication systems has exploded over the past few years, many researchers have taken on the challenge to model wireless channels more accurately. These models are very useful for enhancing the design of all aspects of wireless communications. Smart antennas and systems used in position location are among the most popular new studies that require signal information such as the amplitude, phase, and angle-of-arrival (AOA) of multipath delay spreads. For proper and efficient implementation of future systems, emerging wireless systems must be able to exploit processing of spatial information. The goal of the work presented in this thesis is to further improve two channel modeling tools, SMRCIM and SIRCIM, by implementing new geometrical models that provide users with angle-of-arrival information as well as amplitude and phase data for wideband wireless communication channels. The new angle-of-arrival models are explained and pseudo code is provided to demonstrate the software implementation of the models. Likewise, the channel models are explained and the usage and results of the simulation tools are described. The SMRCIM and SIRCIM tools are currently being used by researchers throughout the world. <i>[Vita removed March 5, 2012. Gmc]</i> / Master of Science

[pt] As características do canal rádio móvel são essenciais ao desenvolvimento de equipamentos e sistemas modernos de telecomunicações sem fio. Para os ambientes nos quais o sistemas operarão, o conhecimento dos principais parâmetros do canal em banda larga é obtido através do uso do conjunto formado por um equipamento transmissor e outro equipamento receptor com suas respectivas antenas. A este conjunto transmissor e receptor atribui-se o nome de sonda. Existem diversas tecnologias sobre as quais as sondas são projetadas e construídas. Em particular mencionam-se as técnicas STDCC (swept time-delay cross-correlation), o Filtro Casado e o OFDM (orthogonal frequency-division multiplexing). Esta tese compara, por simulação, o desempenho de sondas que utilizam estas três técnicas. São propostas alterações nos métodos Filtro Casado e OFDM, de forma que estes proporcionem resultados mais precisos. Além disto, são estudadas imperfeições em dispositivos comuns a todas elas e comparadas sua influência sobre a qualidade das estimações, de forma isolada e combinada. Para o amplificador de potência é considerado o seu principal fator de degradação: suas não linearidades. Para o oscilador local existente no receptor é analisada a contribuição do ruído de fase. O ruído térmico, sempre presente à entrada do receptor em qualquer situação, é variado em uma extensa faixa de valores e o seu efeito sobre a precisão de cada método é analisado. Os resultados obtidos são apresentados na forma de tabelas e gráficos representando, diretamente, o resultado da comparação com o canal de referência ou por meio dos indicadores erro RMS e desvio padrão. / [en] The mobile radio channel characterization is essential to the development of modern wireless telecommunication equipment and systems. The main wideband channel parameters of the environments where these systems will operate are collected by the use of a set comprising a transmitter, a receiver and an aerial system. This set is named sounder. There are many techniques used to project and implement these sounders, such as STDCC (Swept Time-Delay Cross-Correlation), Matched Filter and OFDM (Orthogonal Frequency-Division Multiplexing). This thesis compares, by means of computer simulations, the performance of these three techniques. Some changes are proposed on the Matched Filter and OFDM methods to reach more precise results. Moreover, imperfections in common devices used by all sounders are studied, both independently and jointly, and the impact over the precision of channel estimations is analyzed. The main degradation factor of power amplifiers, which are the nonlinearities, was also considered, as well as the contribution of the phase noise in the receiver local oscillator. The effect of the thermal noise, always present on the receiver input, was also considered, over a large range of values. The results are presented by diagrams and tables showing results of comparisons with a reference channel or by mean of RMS errors and standard deviations.

The dissertation thesis deals with the investigation of the coexistence of GSM–EDGE and UMTS systems with focus on the physical layer of the systems. The aim is to provide a set of recommendations for practical cooperation while the systems operate in both the separated and the common radio bands. A detailed description of signal processing of both the systems on the physical layer is presented. On the basis of this description, models of both systems were created and implemented in the MATLAB environment. The simulations are focused on the physical layer quality parameters, especially the bit error ratio evaluation for various ratios of useful signal power to noise power during the transmission over the radio channel. Simulation is also used to examine the quality of received useful signal while it is interfered by signals from the same and adjacent channels. The purpose is to determine the isolation between these adjacent channels, when the bit error ratio of the useful signal does not exceed a certain reference value. The simulation results are subsequently subjected to comparison with the results of the experimental measurements in laboratory conditions. Before the measurements are carried out, a study of possible interference types is performed. Consequently, the crucial parameters of the measuring equipment used are verified. From the results of simulations and measurements, the proposal of a minimum and recommended carrier separation between both the systems is presented in order to efficiently utilize the assigned frequency spectrum. Furthermore, for the cooperation in both the separated and the common radio bands, the necessary precautions are given for reaching the required isolation and thereby inter-system interference minimization.