The accepted scientific opinion is that anthropogenic activities and correlated greenhouse gases are the main cause of climate change, with carbon dioxide releases from fossil fuels being one of the main culprits. In South Africa, the main sources of energy have always been coal and other fossil fuels. Society and the economy alike are heavily reliant on energy consumption. In light of the above, it is clear that drastic steps need to be taken to "clean up" the nation's energy sector and usage patterns. There is an international tendency towards a so-called "green economy," which finds the relation between economic development, social upliftment and conservation of the natural environment. A green economy relies less on carbon inputs, and utilises resources efficiently, whilst taking a "socially inclusive" approach. It therefore makes sense to draw on renewable natural resources in greening the economy. Some of the advantages of renewable energy are that they result in limited or no emissions, the creation of sustainable jobs, improved health of consumers and enhanced energy security. A shift to a green economy cannot take place in a vacuum. The laws and policies regulating the various sectors of the environment; energy generation, distribution and use; investment opportunities and economic factors must stimulate and drive this move, and must create an optimal atmosphere to this end. This study determines how suitable the current South African legal framework is for a shift towards a green economy based on renewable energy, and whether it can successfully catalyse and drive such a shift. / LLM (Environmental Law and Governance), North-West University, Potchefstroom Campus, 2014

Submitted in fulfilment of the requirements of the Degree of Master of Technology: Biotechnology, Durban University of Technology, 2011. / Due to greenhouse gas emissions from fossil fuel usage, the impending threat of global climate change has increased. The need for an alternative energy feedstock that is not in direct competition to food production has drawn the focus to microalgae. Research suggests that future advances in microalgal mass culture will require closed systems as most microalgal species of interest thrive in highly selective environments. A high lipid producing microalga, identified as Chlorella vulgaris was isolated from a freshwater pond. To appraise the biofuel potential of the isolated strain, the growth kinetics, pyroletic characteristics and photosynthetic efficiency of the Chlorella sp was evaluated in vitro. The optimised preliminary conditions for higher biomass yield of the selected strain were at 4% CO2, 0.5 g l-1 NaNO3 and 0.04 g l-1 PO4, respectively. Pulse amplitude modulation results indicated that C. vulgaris could withstand a light intensity ranging from 150-350 μmol photons m-2s-1. The pyrolitic studies under inert atmosphere at different heating rates of 15, 30, 40 and 50 ºC min-1 from ambient temperature to 800 oC showed that the overall final weight loss recorded for the four different heating rates was in the range of 78.9 to 81%. A tubular photobioreactor was then designed and utilised for biomass and lipid optimisation. The suspension of microalgae was circulated by a pump and propelled to give a sufficiently turbulent flow periodically through the illuminated part and the dark part of the photobioreactor. Microalgal density was determined daily using a Spectrophotometer. Spectrophotometric determinations of biomass were periodically verified by dry cell weight measurements. Results suggest that the optimal NaNO3 concentration for cell growth in the reactor was around 7.5 g l-1, yielding maximum biomass of 2.09 g l-1 on day 16. This was a significant 2.2 fold increase in biomass (p < 0.005) when compared to results achieved at the lowest NaNO3 cycle (of 3.8 g l-1), which yielded a biomass value of 0.95 g l-1 at an OD of 1.178. Lipid accumulation experiments revealed that the microalga did not accumulate significant amounts of lipids when NaNO3 concentrations in the reactor were beyond 1.5 g l-1 (p > 0.005). The largest lipid fraction occurred when the NaNO3 concentration in the medium was 0.5 g l-1. Results suggest that the optimal trade-off between maximising biomass and lipid content occurs at 0.9 g l-1 NaNO3 among the tested conditions within the photobioreactor. Gas chromatograms showed that even though a greater number of known lipids were produced in Run 8, the total lipid percentage was much lower when compared to Runs 9-13. For maximal biomass and lipid from C. vulgaris, it is therefore crucial to optimise nutritional parameters such as NaNO3. However, suitable growth conditions for C. vulgaris in a tubular photobioreactor calls for innovative technological breakthroughs and therefore work is ongoing globally to address this.

Thesis (MScEng)--Stellenbosch University, 2013. / ENGLISH ABSTRACT: In recent times, governments around the world have placed increasing focus on cleaner technologies and sustainable methods of power generation in an attempt to move away from fossil fuel derived power, which is deemed unsustainable and unfriendly to the environment. This trend has also been supported by the South African government, with clear intentions to diversify the country’s power generation by including, among others, biomass as a renewable resource for electricity generation. Woody biomass and associated forestry residues in particular, could potentially be used as such a renewable resource when considering the large amount of fast growing hardwood species cultivated in South Africa. Approximately 6.3 million ton of Eucalyptus grandis is sold annually for pulp production while a further 7 million ton of Eucalyptus species are sold as round wood. With these tree species reaching commercial maturity within 7 – 9 years in the South African climate, there is real potential in harnessing woody biomass as a renewable energy source. In this study, pyrolysis was investigated as a method to condense and upgrade E.grandis into energy and chemical rich products. The pyrolysis of E.grandis is the study of the thermal degradation of the biomass, in the absence of oxygen, to produce char and bio-oil. The thermal degradation behaviour of E.grandis was studied using thermo-gravimetric analysis (TGA) at the Karlsruhe Institute of Technology (KIT) in Germany and subsequently used to determine the isoconversional kinetic constants for E.grandis and its main lignocellulosic components. Slow, Vacuum and Fast Pyrolysis were investigated and optimised to maximise product yields and to identify the key process variables affecting product quality. The Fast Pyrolysis of E.grandis was investigated and compared on bench (KIT0.1 kg/h), laboratory (SU1 kg/h) and pilot plant scale (KIT10 kg/h), using Fast Pyrolysis reactors at Stellenbosch University (SU) in South Africa and at KIT in Germany. The Slow and Vacuum Pyrolysis of E.grandis was investigated and compared using a packed bed reactor at Stellenbosch University. The TGA revealed that biomass particle size had a negligible effect on the thermal degradation behaviour of E.grandis at a heating rate set point of 50 °C/min. It was also shown that increasing the furnace heating rates shifted the thermo-gravimetric (TG) and differential thermo-gravimetric (DTG) curves towards higher temperatures while also increasing the maximum rate of volatilisation. Lignin resulted in the largest specific char yield and also reacted across the widest temperature range of all the samples investigated. The average activation energies found for the samples investigated were 177.8, 141.0, 106.2 and 170.4 kJ/mol for holocellulose, alpha-cellulose, Klason lignin and raw E.grandis, respectively. Bio-oil yield was optimised at 76 wt. % (daf) for the SU1 kg/h Fast Pyrolysis plant using an average biomass particle size of 570 μm and a reactor temperature of 470 °C. Differences in the respective condensation chains of the various Fast Pyrolysis reactor configurations investigated resulted in higher gas and char yields for the KIT reactor configurations compared to the SU1 kg/h Fast Pyrolysis plant. Differences in the vapour residence time between Slow (>400 s) and Vacuum Pyrolysis (< 2 s) resulted in a higher liquid and lower char yield for Vacuum Pyrolysis. Local liquid yield maxima of 41.1 and 64.4 wt. % daf were found for Slow and Vacuum Pyrolysis, respectively (achieved at a reactor temperature of 450 °C and a heating rate of 17 °C/min). Even though char yields were favoured at low reactor temperatures (269 – 300 °C), the higher heating values of the char were favoured at high reactor temperatures (29 – 34 MJ/kg for 375 – 481 °C). Reactor temperature had the most significant effects on product yield and quality for the respective Slow and Vacuum Pyrolysis experimental runs. The bio-oils yielded for SP and VP were found to be rich in furfural and acetic acid. / AFRIKAANSE OPSOMMING: Regerings regoor die wêreld het in die afgelope tyd toenemende fokus geplaas op skoner tegnologie en volhoubare metodes van kragopwekking in 'n poging om weg te beweeg van fossielbrandstof gebasseerde energie, wat geag word as nie volhoubaar nie en skadelik vir die omgewing. Hierdie tendens is ook ondersteun deur die Suid-Afrikaanse regering, met 'n duidelike bedoeling om die land se kragopwekking te diversifiseer deur, onder andere, biomassa as 'n hernubare bron vir die opwekking van elektrisiteit te gebruik. Houtagtige biomassa en verwante bosbou afval in die besonder, kan potensieel gebruik word as so 'n hernubare hulpbron, veral aangesien ‘n groot aantal vinnig groeiende hardehout spesies tans in Suid-Afrika verbou word. Ongeveer 6,3 miljoen ton Eucalyptus grandis word jaarliks verkoop vir pulp produksie, terwyl 'n verdere 7 miljoen ton van Eucalyptus spesies verkoop word as paal hout. Met hierdie boom spesies wat kommersiële volwassenheid bereik binne 7 - 9 jaar in die Suid-Afrikaanse klimaat, is daar werklike potensiaal vir die benutting van houtagtige biomassa as 'n hernubare energiebron. In hierdie studie is pirolise ondersoek as 'n metode om E.grandis te kondenseer en op te gradeer na energie en chemikalie ryke produkte. Die pirolise van E.grandis is die proses van termiese afbreking van die biomassa, in die afwesigheid van suurstof, om houtskool en bio-olie te produseer. Die termiese afbrekingsgedrag van E.grandis is bestudeer deur gebruik te maak van termo-gravimetriese analise (TGA) by die Karlsruhe Instituut van Tegnologie in Duitsland en daarna gebruik om die kinetiese konstantes vir die iso-omskakeling van E.grandis en sy hoof komponente te bepaal. Stadige, Vakuum en Snel pirolise is ondersoek en geoptimiseer om produk opbrengste te maksimeer en die sleutel proses veranderlikes wat die kwaliteit van die produk beïnvloed te identifiseer. Die Snel Pirolise van E.grandis is ondersoek en vergelyk op bank- (KIT0.1 kg / h), laboratorium- (SU1 kg / h) en proefaanlegskaal (KIT10 kg / h) deur gebruik te maak van Snel pirolise reaktore by die Universiteit van Stellenbosch (US) in Suid-Afrika en die Karlsruhe Instituut van Tegnologie (KIT) in Duitsland. Die Stadige en Vakuum Pirolise van E.grandis is ondersoek en vergelyk met behulp van 'n gepakte bed reaktor aan die Universiteit van Stellenbosch. Die TGA studie het openbaar dat biomassa deeltjiegrootte 'n onbeduidende uitwerking op die termiese afbrekingsgedrag van E.grandis het by 'n verhittings tempo van 50 ° C / min. Dit is ook bewys dat die verhoging van die oond verwarming tempo die termo-gravimetriese (TG) en differensiële termo-gravimetriese (DTG) kurwes na hoër temperature verskuif, terwyl dit ook die maksimum tempo van vervlugtiging laat toeneem het. Lignien het gelei tot die grootste spesifieke houtskool opbrengs en het ook oor die wydste temperatuur interval gereageer van al die monsters wat ondersoek is. Die gemiddelde aktiveringsenergieë vir die monsters wat ondersoek is, was 177,8, 141,0, 106,2 en 170,4 kJ / mol, onderskeidelik vir holosellulose, alpha-sellulose, Klason lignien en rou E.grandis. Bio-olie opbrengs is geoptimeer teen 76 wt. % (DAF) vir die SU1 kg / h Snel Pirolise aanleg met behulp van 'n gemiddelde biomassa deeltjiegrootte van 570 μm en 'n reaktor temperatuur van 470 ° C. Verskille in die onderskeie kondensasie kettings van die verskillende Snel Pirolise aanlegte wat ondersoek is, het gelei tot hoër gas- en houtskool opbrengste vir die KIT reaktor konfigurasies in vergelyking met die SU1kg/h FP plant. Verskille in die damp retensie tyd tussen Stadige (> 400 s) en Vakuum pirolise (<2 s) het gelei tot 'n hoër vloeistof en laer houtskool opbrengs vir Vakuum Pirolise. Plaaslike vloeistof opbrengs maksima van 41,1 en 64,4 wt. % (daf) is gevind vir Stadig en Vakuum pirolise onderskeidelik, bereik by 'n reaktor temperatuur van 450 ° C en 'n verhittingstempo van 17 ° C / min. Selfs al is houtskool opbrengste bevoordeel by lae reaktor temperature (269 - 300 ° C), is die hoër warmte waardes van die houtskool bevoordeel deur hoë reaktor temperature (29 - 34 MJ / kg vir 375 - 481 ° C). Reaktor temperatuur het die mees beduidende effek op die produk opbrengs en kwaliteit vir die onderskeie Stadige Pirolise en Vakuum Pirolise eksperimentele lopies gehad. Die bio-olies geproduseer tydens Stadige en Vakuum Pirolise was ryk aan furfuraal en asynsuur.

Thesis (MScEng)--Stellenbosch University, 2011. / ENGLISH ABSTRACT: As the push continues for increased use of renewables on the electricity grid, the problem of energy storage is becoming more urgent than ever. Flywheels with wound, composite rotors represent an efficient and environmentally friendly option for energy storage. They have already been applied successfully for voltage control on electrical rail networks and for bridging power in backup UPS systems, but lately they have also proven useful for grid-scale frequency regulation. For flywheels to be deployed on a wider scale, the high cost associated with the technology will have to be addressed. An important driver of cost is the density at which energy can be stored. Currently, flywheel designs do not consistently achieve high energy density, and this study investigates the reasons for this. A critical analysis is made of the design methodologies that have been proposed in the available literature, and some improvements are suggested. Most notably it is shown that significant improvements in energy density may be possible if the design optimization problem is formulated carefully. In addition, the problem of material selection is discussed, because material properties have a significant influence on energy density. Some guidance is given for flywheel designers on how to choose an optimal set of materials without invoking undue computational effort. It is hoped that these suggestions may be carried forward as a topic of further research. / AFRIKAANSE OPSOMMING: Namate die aanvraag vir hernubare energie op die elektrisiteit netwerk vergroot, word die probleem van energie berging van kardinale belang. Vliegwiele met silindriese rotors van samegestelde materiale bied ’n effektiewe en omgewingsvriendelike opsie vir energieberging. Hierdie tipe vliegwiele is reeds suksesvol aangewend vir spanningsbeheer op elektriese spoornetwerke en om oorbruggingskrag te voorsien aan rugsteun sisteme. Meer onlangs is hulle ook nuttig bewys vir die regulasie van frekwensie op die elektrisiteit netwerk. Grootskaalse aanwending van vliegwiele kan egter slegs oorweeg word indien die hoë koste van die tegnologie aangespreek word. Een van die onderliggende redes vir die hoë koste van vliegwiele is die relatiewe lae digtheid waarby energie geberg kan word, en hierdie studie ondersoek die redes hiervoor. Die ontwerpmetodiek wat in die beskikbare literatuur voorgestel is, word krities geanaliseer en ’n paar verbeteringe word aanbeveel. Mees noemenswaardig is die opmerklike verbeteringe in energie-digtheid wat soms moontlik is indien die optimerings-probleem deurdag geformuleer word. Omdat materiaaleienskappe ’n bepalende invloed op energie digtheid uitoefen word die probleem van materiaalseleksie ook verder bespreek. ’n Paar riglyne vir die seleksie van ’n optimale stel materiale sonder om oordrewe berekenings-inspanning te veroorsaak, word aan vliegwielontwerpers gegee. Hierdie voorstelle kan hopelik in die toekoms verder deurgetrap word as onderwerp vir verdere studies.

This thesis focuses on the single-phase voltage-source inverter for use in photovoltaic (PV) electricity generating systems in both stand-alone and grid-tied applications. In many cases, developments in single-phase PV systems have followed developments in three-phase systems. Time-variant systems are more difficult to control than time-invariant systems. Nevertheless, by using suitable transformation techniques, time-variant systems can often be modelled as time-invariant systems. After the transformation, the control signals that are usually time-variant (often varying sinusoidally in time) become time-invariant at the fundamental frequency, and are hence much easier to deal with. With this approach, synchronous rotating frame control techniques have been previously proposed for high performance three-phase inverter applications. The transformation theory cannot be applied directly in single-phase systems without modification, and the d-q components would not be time-invariant in situations where harmonics, resonances or unbalance is present. Single-phase inverter controller designs based on the use of a synchronous rotating reference frame have been proposed, but such designs do not always perform as well as expected. This thesis aims to improve single-phase voltage-source inverters. The main objective is to address, in terms of cost, efficiency, power management and power quality, the problems found with single-phase designs based on a synchronous rotating frame single-phase inverter controller. Consequently, this thesis focuses on a novel controller approach in order to obtain a more reliable and flexible single-phase inverter. As the first step, this thesis investigates the single-phase inverter switching gate-drive algorithms and develops a form of space-vector pulse-width-modulation (SVPWM) in order to reduce total harmonic distortion. The results of the new SVPWM algorithm demonstrate its superior performance when compared with sinusoidal pulse-width-modulation (SPWM) which is often used with single-phase inverters. The second step, which is further reviewed and presented in this thesis, is the modelling of the single-phase inverter control based on the synchronous rotating frame. A mathematical analysis is conducted to determine the mechanism of the coupling that exists between the voltage phase and amplitude terms, and a new transformation strategy is proposed based on using the voltage phase as a reference at the Park transformation stages, and the current phase as a reference for the current at the transformation stages. The line-frequency components of the feedback signals are transformed to time-invariant components, thus eliminating the ripple and reducing the computational burden associated with the controller stage. Consequently, the inverter feedback controller stage is designed so that the coupling terms are decoupled within the controller itself. The effectiveness of the techniques proposed in this thesis are demonstrated by simulation using the MATLAB/SIMULINK environment. The proposed technique was also investigated through a practical implementation of the control system using a Digital Signal Processor (DSP) and a single-phase inverter. This practical system was tested up to 1 kW only (limited by the available inverter hardware). Nevertheless, the correlation between the simulation and the practical results is high and this gives confidence that the developed mechanism will allow the 2.5kW goal to be achieved. Practical test cases illustrate the effectiveness of the models. In addition, the comparisons between experimental and simulation results permit the system's behaviour and performance to be accurately evaluated. With the development of the new controller, small-scale single-phase renewable energy systems will become more useful in the field of power quality management through their ability to separately control the phase and amplitude of the output voltage. Consequently, incorporation of this type of generator within the national electrical distribution network, as distributed generators (DG) at low-voltage level, can assist with power quality management at the consumer side of the grid. In addition, such a generator can also operate in stand-alone mode if the grid becomes unavailable. The third step in this thesis investigates small-scale single-phase renewable energy systems operating as decentralized distributed generators within a local network. This operation is achieved by controlling the inverter side using the quantities measured at the common coupling point between the grid and the inverter, without requiring other extensive communications. Thus, the small-scale single-phase renewable energy distributed generator systems will contain only a local controller at each installation.

Forest biomass burned for energy purposes does not need to be accounted for under IPCC rules. This has led to a number of countries considering tree stump harvesting as a source of forest biomass. However there are concerns that the soil disturbance that this may entail could have adverse environmental effects, including the loss of sequestered carbon from the soil. Published results differ in the degree and nature of stump harvesting soil disturbance. Two widely used measures employed in stump harvesting soil disturbance studies are visual assessment of disturbance extent and bulk density measures of the nature of disturbance. Each of these has limitations. This study seeks to extend the insight into both the nature and extent of soil disturbance resulting from stump harvesting by the application of additional techniques. In this way the physical effects of soil disturbance by stump harvesting will be compared with those of other forestry practices. To overcome the two-dimensional and subjective nature of visual assessment, a radiometric approach was adopted, utilising residual Chernobyl 137Cs fallout to determine the degree of soil mixing. To complement bulk density measurements, micromorphological analyses of soil thin sections taken from field samples were carried out to investigate the impact of compressive force on pore space. Low-cost tracer devices were deployed in the soil around stumps prior to extraction to permit the monitoring of the lateral movement of soil during stump extraction. These methods were applied to a stump harvesting operation carried out under current UK guidance at a UPM Tilhill managed site in south west Scotland. The radiometric method demonstrated its capacity to recognise differing degrees of soil disturbance in an operational forest environment, including some disturbance that might escape visual assessment. Analysis of soil thin sections provided the evidence of a significant increase in the pore capacity of disturbed soil. The soil movement tracers developed for this project provided the capability to examine the various trajectories of soil during stump extraction as well as dimensioning the resulting disturbance crater. The study indicated that under current UK management and operational practice, stump harvesting generated a higher level of soil disturbance compared to ground preparation by trench mounding, with an estimated 1260 m3 ha-1 of soil disturbed by stump harvesting compared to 250 m3 ha-1 from trench mounding. Stump harvesting was found to generate a net reduction in soil bulk density in the affected areas, contrary to the findings of some other studies. This outcome is dependent on adhering to particular site management and operational procedures. The practice of raking over the site following stump harvesting is estimated to add a further 10% to the volume of soil disturbed, and is a questionable activity under soil sustainability guidance. This work was part-funded and actively supported by the UK Forestry Commission and UPM Tilhill.

As an increasing number of homeowners decide to take advantage of distributed renewable resources such as rooftop solar, we may need to rethink the current regulatory paradigm and governance structure of the electric market. This thesis examines the shortcomings of current net metering programs in California. While the current Net Metering 2.0 proceeding highlights a clash of solar advocates and electric utilities, it is in fact revealing an underlying structural flaw that has been present all along. In order to send the appropriate price signals to solar customers, both the structure by which utilities recover costs and the rate at which solar customers are compensated must be reconceived. I show how the current debates over the appropriate price to compensate solar customer are built on a flawed rate structure. Without addressing the underlying inefficiencies of current rate structures, it is unlikely that we will maintain utilities’ financial ability to operate and maintain grid infrastructure and provide solar customers with the proper incentives to reach the ideal transition to solar energy.

Sustainable Built Environments Senior Capstone Project / This capstone project evaluates the current state of floating solar photovoltaic technology and proposes use of the technology on water management infrastructure in Arizona. The study finds that floating solar photovoltaic has a higher energy density (100 W/m^2) than land-based, utility-scale solar and does not involve significant cost increases. The study proposes and models a small pilot installation on Lake Pleasant Reservoir, part of the Central Arizona Project, and finds that lifetime costs per unit energy are higher than what the Central Arizona Project currently pays for energy, assuming US median per-wattinstalled costs for commercial solar. This cost however does not factor in savings from water conservation, existing infrastructure, reduced land costs, or other benefits. The study recommends water reservoirs by hydropower dams as ideal locations for floating photovoltaic installations. Justified with a significant background on Arizona’s environmental, social, and economic sustainability, as well as regulations calling for increased renewable energy generation and reduced carbon emissions, this study recommends aggressive implementation of floating solar photovoltaic technology within a sustainable development paradigm.

The rise of environmental awareness as well as the unstable global fossil fuel market has brought about government initiatives to increase electricity generation from renewable energy sources. These resources tend to be geographically and electrically remote from load centres. Consequently many Distributed Generators (DGs) are expected to be connected to the existing Distribution Networks (DNs), which have high impedance and low X/R ratios. Intermittence and unpredictability of the various types of renewable energy sources can be of time scales of days (hydro) down to seconds (wind, wave). As the time scale becomes smaller, the output of the DG becomes more difficult to accommodate in the DN. With the DGs operating in constant power factor mode, intermittence of the output of the generator combined with the high impedance and low X/R ratios of the DN will cause voltage variations above the statutory limits for quality of supply. This is traditionally mitigated by accepting increased operation of automated network control or network reinforcement. However, due to the distributed nature of RES, automating or reinforcing the DN can be expensive and difficult solutions to implement. The Thesis proposed was that new methods of controlling DG voltage could enable the connection of increased capacities of plant to existing DNs without the need for network management or reinforcement. The work reported here discusses the implications of the increasing capacity of DG in rural distribution networks on steady-state voltage profiles. Two methods of voltage compensation are proposed. The first is a deterministic system that uses a set of rules to intelligently switch between voltage and power factor control modes. This new control algorithm is shown to be able to respond well to slow voltage variations due to load or generation changes. The second method is a fuzzy inference system that adjusts the setpoint of the power factor controller in response to the local voltage. This system can be set to respond to any steady-state voltage variations that will be experienced. Further, control of real power is developed as a supplementary means for voltage regulation in weak rural networks. The algorithms developed in the study are shown to operate with any synchronous or asynchronous generation wherein real and reactive power can be separately controlled. Extensive simulations of typical and real rural systems using synchronous generators (small hydro) and doubly-fed induction generators (wind turbines) have verified that the proposed approaches improve the voltage profile of the distribution network. This demonstrated that the original Thesis was true and that the techniques proposed allow wider operation of greater capacities of DG within the statutory voltage limits.

Thesis (MScEng)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: Concentrating solar power promises to be a potential solution for meeting the worlds energy needs in the future. One of the key features of this type of renewable energy technology is its ability to store energy effectively and relatively cheaply. An air-rock bed thermal energy storage system promises to be an effective and reasonably inexpensive storage system for concentrating solar power plants. Currently there is no such storage system commercially in operation in any concentrating solar power plant, and further research is required before such a system can be implemented. The main research areas to address are the thermal-mechanical behaviour of rocks, rock bed pressure drop correlations and effective and practical system designs. Recent studies have shown that the pressure drop over a packed bed of rocks is dependant on various aspects such as particle orientation relative to the flow direction, particle shape and surface roughness. The irregularity and unpredictability of the particle shapes make it difficult to formulate a general pressure drop correlation. Typical air-rock bed thermal design concepts consist of a large vertical square or cylindrical vessel in which the bed is contained. Such system designs are simple but susceptible to the ratcheting effect and large pressure drops. Several authors have proposed concepts to over-come these issues, but there remains a need for tools to prove the feasibility of the designs. The purpose of this paper is to investigate aDEM-CFD coupled approach that can aid the development of an air-rock bed thermal energy storage system. This study specifically focuses on the use of CFD. A complementary study focusses on DEM. The two areas of focus in this study are the pressure drop and system design. A discrete CFD simulation model is used to predict pressure drop over packed beds containing spherical and irregular particles. DEM is used to create randomly packed beds containing either spherical or irregularly shaped particles. This model is also used to determine the heat transfer between the fluid and particle surface. A porous CFD model is used to model system design concepts. Pressure drop and heat transfer data predicted by the discrete model, is used in the porous model to describe the pressure drop and thermal behaviour of a TES system. Results from the discrete CFD model shows that it can accurately predict the pressure drop over a packed bed of spheres with an average deviation of roughly 10%fromresults found in literature. The heat transfer between the fluid and particle surface also is accurately predicted, with an average deviation of between 13.36 % and 21.83 % from results found in literature. The discrete CFD model for packed beds containing irregular particles presented problems when generating a mesh for the CFD computational domain. The clump logic method was used to represent rock particles in this study. This method was proven by other studies to accurately model the rock particle and the rock packed bed structure using DEM. However, this technique presented problems when generating the surface mesh. As a result a simplified clump model was used to represent the rock particles. This simplified clump model showed characteristics of a packed bed of rocks in terms of pressure drop and heat transfer. However, the results suggest that the particles failed to represent formdrag. This was attributed to absence of blunt surfaces and sharp edges of the simplified clumpmodel normally found on rock particles. The irregular particles presented in this study proved to be inadequate for modelling universal characteristics of a packed bed of rocks in terms of pressure drop. The porous CFD model was validated against experimental measurement to predict the thermal behaviour of rock beds. The application of the porous model demonstrated that it is a useful design tool for system design concepts. / AFRIKAANSE OPSOMMING: Gekonsentreerde sonkrag beloof om ’n potensiële toekomstige oplossing te wees vir die wêreld se groeiende energie behoeftes. Een van die belangrikste eienskappe van hierdie tipe hernubare energie tegnologie is die vermoë om energie doeltreffend en relatief goedkoop te stoor. ’n Lug-klipbed termiese energie stoorstelsel beloof om ’n doeltreffende en redelik goedkoop stoorstelsel vir gekonsentreerde sonkragstasies te wees . Tans is daar geen sodanige stoorstelsel kommersieël in werking in enige gekonsentreerde sonkragstasie nie. Verdere navorsing is nodig voordat so ’n stelsel in werking gestel kan word. Die belangrikste navorsingsgebiede om aan te spreek is die termies-meganiese gedrag van klippe, klipbed drukverlies korrelasies en effektiewe en praktiese stelsel ontwerpe. Onlangse studies het getoon dat die drukverlies oor ’n gepakte bed van klippe afhanklik is van verskeie aspekte soos partikel oriëntasie tot die vloeirigting, partikel vormen oppervlak grofheid. Die onreëlmatigheid en onvoorspelbaarheid van die klip vorms maak dit moeilik om ’n algemene drukverlies korrelasie te formuleer. Tipiese lug-klipbed termiese ontwerp konsepte bestaan uit ’n groot vertikale vierkantige of silindriese houer waarin die gepakte bed is. Sodanige sisteem ontwerpe is eenvoudig, maar vatbaar vir die palrat effek en groot drukverliese. Verskeie studies het voorgestelde konsepte om hierdie kwessies te oorkom, maar daar is steeds ’n behoefte aanmetodes om die haalbaarheid van die ontwerpe te bewys. Die doel van hierdie studie is om ’n Diskreet Element Modelle (DEM) en numeriese vloeidinamika gekoppelde benadering te ontwikkel wat ’n lug-klipbed termiese energie stoorstelsel kan ondersoek. Hierdie studie fokus spesifiek op die gebruik van numeriese vloeidinamika. ’n Aanvullende studie fokus op DEM. Die twee areas van fokus in hierdie studie is die drukverlies en stelsel ontwerp. ’n Diskrete numeriese vloeidinamika simulasie model word gebruik om drukverlies te voorspel oor gepakte beddens met sferiese en onreëlmatige partikels. DEM word gebruik om lukraak gepakte beddens van óf sferiese óf onreëlmatige partikels te skep. Hierdie model is ook gebruik om die hitte-oordrag tussen die vloeistof en partikel oppervlak te bepaal. ’n Poreuse numeriese vloeidinamika model word gebruik omdie stelsel ontwerp konsepte voor te stel. Drukverlies en hitte-oordrag data, voorspel deur die diskrete model, word gebruik in die poreuse model om die drukverlies- en hittegedrag van ’n TES-stelsel te beskryf. Resultate van die diskrete numeriese vloeidinamikamodel toon dat dit akkuraat die drukverlies oor ’n gepakte bed van sfere kan voorspel met ’n gemiddelde afwyking van ongeveer 10%van die resultatewat in die literatuur aangetref word. Die hitte-oordrag tussen die vloeistof en partikel oppervlak is ook akkuraat voorspel, met ’n gemiddelde afwyking van tussen 13.36%en 21.83%van die resultate wat in die literatuur aangetref word. Die diskrete numeriese vloeidinamika model vir gepakte beddens met onreëlmatige partikels bied probleme wanneer ’n maas vir die numeriese vloeidinamika, numeriese domein gegenereer word. Die "clump"logika metode is gebruik om klip partikels te verteenwoordig in hierdie studie. Hierdiemetode is deur ander studies bewys om akkuraat die klip partikel en die klip gepakte bed-struktuur te modelleer deur die gebruik van DEM. Hierdie tegniek het egter probleme gebied toe die oppervlak maas gegenereer is. As gevolg hiervan is ’n vereenvoudigde "clump"model gebruik om die klip partikels te verteenwoordig. Die vereenvoudigde "clump"model vertoon karakteristieke eienskappe van ’n gepakte bed van klippe in terme van drukverlies en hitte oordrag. Die resultate het egter getoon dat die partikels nie vorm weerstand verteenwoordig nie. Hierdie resultate kan toegeskryf word aan die afwesigheid van gladde oppervlaktes en skerp kante, wat normaalweg op klip partikels gevind word, in die vereenvoudigde "clump"model. Die oneweredige partikels wat in hierdie studie voorgestel word, blykomnie geskik tewees vir die modellering van die universele karakteristieke eienskappe van ’n gepakte bed van klippe in terme van drukverlies nie. Die poreuse numeriese vloeidinamika model is met eksperimentele metings bevestig omdie termiese gedrag van klipbeddens te voorspel. Die toepassing van die poreuse model demonstreer dat dit ’n nuttige ontwerp metode is vir stelsel ontwerp konsepte.