Articulated rigid-rod polymers asPBI were synthesized via polycondensation reaction. Using 2-sulfoterephthalic acid and 5-sulfoisophthalic acid in different ratios for copolycondensation reaction making the fully conjugated rigid-rod backbone became articulated. Both rigid-rod and articulated rigid-rod were further derivatized using alkane sulfonated pendants and became water-soluble rigid-rod and articulated rigid-rod polyelectrolytes. Lithium salt doped cast films of the polyelectrolytes showed a root-temperature DC conductivity parallel to film surface (

Development of opto-electronic polymers has been focused on conjugated rigid-rod polymers which assume a para-catenated backbone yielding a rod-like configuration. As a consequence of their rigidity, the rod-like molecules display superior mechanical properties, thermo-oxidative stability and solvent resistance. The later two characters cause difficulties in processing these high-performance rigid-rod polymers. This in terms limits their applications in critical technologies, such as conducting polymers, nonlinear optics, and solid polyelectrolytes. In this study, chemical derivatives of the rigid-rod polymers were synthesized using pendants of propane-sulfonated ionomers to (1) enhance the solubility of the rigid-rod polymers, and (2) generate a solid polyelectrolyte suitable for energy storage. Extensive synthesis efforts were focused on generating monomers and polymers of propane-sulfonated poly(p-phenylene-benzobisimidazole), PBI, making it a water soluble electrolyte. Various analysis techniques were applied to ascertain the chemical structure and the purity of the monomers and of the polymers. The polymer molecular weight was also determined using viscometry. An intrinsic viscosity of 4.9 dL/g was achieved for the 2-sulfo-PBI and of 0.58 dL/g for the propane-sulfonated PBI with Na+ ionomer pendants

This study utilized polycondensation reaction to synthesize fully conjugated rod-like polymer dihydroxy-PBI. Chemical derivatizations were applied to attach pendants of propane sulfonic coil for dihydroxy-PBI-PS and to attach aromatic phenylene ring with Li ionic moiety for dihydroxy-PBI-AS. The attachment of pendants for dihydroxy-PBI-PS was 42.27 % and for dihydroxy-PBI-AS was only for 0.04 % causing by stereo hindrance of this molecule. These polymers seemed to have good thermal stability. Dihydroxy-PBI started to show degradation at 467.8 oC and retained 60.5 wt. % at 800 oC. Derivatized dihydroxy- PBI-PS and dihydroxy-PBI-AS lost their pendants at 295.3 oC and 314.4 oC, respectively. Dihydroxy-PBI was cast into thin film. Upon doping with lithium salt of LiClO at 2.02 wt. %, dihydroxy-PBI cast film showed the highest room-temperature dc conductivity parallel to the film (£m¡ü) of 1.71 x 10-4 S/cm and perpendicular to the film (£m¡æ) of 1.49 x 10-5 S/cm. For dihydroxy-PBI-PS cast film, the highest conductivity was at 0.49 wt. % of LiClO4 with £m¡ü of 1.05 x 10-3 S/cm and £m¡æ of 1.05 x 10-4 S/cm. For dihydroxy-PBI-AS cast film, the highest conductivity was at 2.02 wt. % of LiClO4 with £m¡ü of 1.32 x 10-3 S/cm and £m¡æ of 2.26 x 10-5 S/cm. From scanning electron microscopy and wide-angle x-ray scattering, it was learned that cast films of dihydroxy-PBI and dihydroxy-PBI-AS had anisotropic layered structure parallel to the film, and that of dihydroxy-PBI-PS showed less of this anisotropy.

Polymer light emitting diodes (PLED) were using a heterocyclic aromatic rigid-rod polymer poly-p-phenylene-benzobisoxazole (PBO) as an opto-electronically active layer; and poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonic acid) (PEDOT:PSS) as a hole transporting layer. Aluminum (Al) and indium tin oxide (ITO) were served as device cathode and anode, respectively. [6,6]-phenyl C61-butyric acid methyl ester (PC61BM) or derivatized multi-wall carbon nano-tube (MWCNT-C18), with great electron transporting ability, was doped into PBO to enhance the performance of PLED devices as well as the thin-film electrical conductivity. The optical length was changed by using different spin coating speeds and durations. From the research, the £fmax of electroluminescence (EL) was blue-shifted as PEDOT:PSS spin coating speed increased for a thinner layer. Once using a higher spin coating speed repeatedly to coat PEDOT:PSS, the £fmax of electroluminescence was red-shifted. If the PEDOT:PSS film thicknesses were similar, the EL spectra were almost the same, independent of device processing scheme. The injection current and EL intensity were enhanced by doping PC61BM or MWCNT- C18. The electric conductivity parallel to film surface (£m¡ü) was increased as the doping concentration increased. Because of the extremely different aspect ratio, the MWCNT-C18 had a lower percolation threshold concentration. Therefore, at a low MWCNT-C18 doping concentration, the injection current and the EL intensity were enhanced compared with those of PC61BM.

The focus of this study is mono-layer polymer light emitting diode (PLED). The emitting layer is poly-p-phenylenebenzobisoxazole (PBO). PBO is a fully conjugated heterocyclic aromatic rigid-rod polymer. Anode is indium-tin-oxide (ITO). Cathode is aluminum (Al). We used UV epoxy resin to package PLED devices, then measured current-voltage response, electroluminescence (EL) emission, and device lifetime. We demonstrate that the packaged mono-layer PBO LED reduced its demise from water and oxygen. Device lifetime increased from 1 hour to several hundred hours. At a larger bias voltage or current, emission intensity and device efficiency became higher. But decay rate increased leading to shortened device lifetime. Device temperature appeared linearly with current density. A red shift of the EL emission was observed. The £fmax. of emission spectra moved from 534 nm (initial) to 582 nm (after 100 hrs). After thermal annealing at 120¢J for ten hours, threshold voltage increased from 5 V to 12 V, current density decreased to several 10 mA/cm2, luminous intensity improved several ten times to 10-2 cd/m2, emission color changed from yellow-green to orange, luminous efficiency improved from 10-7 to 10-4 cd/A, but device lifetime declined to less than 20 hrs.

Polycondensation reaction was carried out for synthesizing rigid-rod polymer hPBI. Various molar ratios (50:1, 25:1, and 15:1) of 2-hydroterephthalic acid and 5-hydroisophthalic acid were also introduced in the synthesis for articulated rigid-rod polymer a-hPBI. The polymers were further derivatized with 1,3-propanesulton for pendants of lithium ionomer to become water soluble polyelectrolytes hPBI-PS(Li+) and a-hPBI-PS(Li+), respectively. Lithium salt doped cast film of the rigid-rod polyelectrolyte hPBI-PS(Li+) showed a room-temperature DC conductivity parallel to film surface as high as 4.02¡Ñ10-3 S/cm. Molecular weight of the rigid-rod polyelectrolyte was low indicating a small molecular aspect ratio. In cast film, the molecules were randomly distributed and highly isotropic facilitated Li cations mobility for a high film conductivity. The conductivity was also insensitive to the anion of lithium salt. No apparent layered structure was revealed by scanning electron microscope suggesting that the cast films had near three-dimensionally isotropic structure and conductivity.

Polymer photovoltaic cell (PV cell) utilizes a polymer to absorb photons for generating excitons. When excitons are separated into electrons and holes, the device has the photovoltaic effect. Polymer light emitting diode (PLED) injects electrons and holes respectively from cathode and anode into a polymer emission layer. Some of the electrons and the holes would recombine to induce light emission. This research used a heterocyclic aromatic rigid-rod polymer poly-p-phenylene- benzobisoxazole (PBO) as the opto-electronic layer, and a conducting material of poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonic acid) (PEDOT:PSS) as the hole transport layer. PV cells were fabricated using indium-tin-oxide (ITO) as anode and aluminium as cathode. Same layer arrangement was applied for PLEDs. These two kinds of devices were measured for electrical and optical response. It was evidenced that the addition of PEDOT:PSS layer facilitated the separation of excitons into electrons and holes at the PBO/PEDOT:PSS interface. Insertion of a LiF layer between PBO layer and Al cathode reduced their energy band gap and facilitated charge transport leading to an enhanced efficiency for PV cells and PLEDs. Thickness variations were found on spun PBO layer. According to emission intensity, we knew that the PBO layer quality was significant for electroluminescence. Introduction of a PEDOT:PSS layer improved the interface between ITO and PBO. The thickness of PEDOT:PSS layer depended on the ITO surface roughness. With a PEDOT:PSS layer, the opto-electronic efficiency of PV cell and PLED was improved.

Poly-p-phenylenebenzobisoxazole (PBO) and carbon nanotube (CNT) contain fully conjugated rod like backbone entailing excellent mechanical properties, thermo -oxidative stability and solvent resistance. Rigid-rod PBO is commonly processed by dissolving in methanesulfonic acid or Lewis acid. A CNT of multi-wall carbon nanotube (MWNT) was dissolved in a Lewis acid solution of PBO for dispersion, and then spun for thin film. MWNT concentration in the films was from zero up to 5 wt. %. Compared to that of pure PBO film, all PBO/MWNT composite films retained same but enhanced UV-Vis absorption peaks, according to MWNT concentration, showing that PBO and MWNT did not have overlapping electron orbitals affecting their energy gaps. The composite films were excited at 325 nm using a He-Cd laser for photoluminescence (PL) emission. All PL spectra had maximum intensity at 540 nm indicative of yellow-green light emission. The composite films were fabricated as light emitting diodes using indium-tin-oxide/glass as substrate and anode, as well as vacuum evaporated Al as cathode for respectively hole and electron injectors. In these light emitting devices, MWNT doped PBO would decrease threshold voltage for about 2 V. Up to 0.1 wt. % of MWNT, the device emission current was increased two orders of magnitude than those of the devices without MWNT. Further increase of MWNT caused a successive decrease in electroluminescence emission intensity attributed to a quench effect from aggregations of MWNTs. UV epoxy resin was applied to package the mono-layer and bilayer PBO light emitting devices. The UV epoxy resin had some gas release during encapsulation. The devices were packaged with vacuum and without vacuum encapsulation. It was demonstrated that the device encapsulation reduced its demise from water and oxygen. The vacuum encapsulation could remove gaseous volatile of the device to inhibit oxygen and moisture to prolong device lifetime. The main degradation of light emitting device was the oxidization of cathode. The interactions between nitrogen of PBO and H2O caused the formation of hydrogen bonding at room temperature. Oxygen and moisture diffused into PBO polymer and were suspected to form mid-gap state for the polymer. The mid energy band disappeared upon heat treatment before encapsulation. A device under a higher bias voltage was found to have a shorter lifetime, but a larger EL emission intensity. The EL emission intensity was not a constant under a constant current bias. The vacuum encapsulated device had two or twenty times lifetime than, respectively, the device encapsulation without vacuum evacuation or in ambient conditions. The sandwich structure of ITO/PBO/Al had no observable photovoltaic effect due to insufficient exciton separation into electrons and holes. Poly(2,3-dihydro thieno-1,4-dioxin):polystyrenesulfonate (PEDOT:PSS), a hole transferring medium, was spun into a thin-film between PBO and indium-tin-oxide to facilitate photovoltaic (PV) effect by forming a donor-acceptor interlayer to separate and to transport photoinduced charges. Optimum PBO thickness for the PV heterojunctions was about 71 nm at which the hole transferring PEDOT:PSS generated the maximum short circuit current (Isc) at a thickness of 115 nm. By using a layer of lithium fluoride (LiF) as an electron transferring layer adhering to Al cathode, the most open circuit voltage (Voc) and the maximum short circuit current (Isc) were achieved with a LiF thickness of 1-2 nm due to possible electric dipole effect leading to an increase of Voc from 0.7 V to 0.92 V and of Isc from about 0.1

A heterocyclic aromatic rigid-rod polymer poly-p-phenylene-benzobisoxazole (PBO) was applied as the opto-electronic layer¡Fand a conducting material of poly(3,4-ethylenedioxythio-phene):poly(4-styrenesulfonic acid) (PEDOT: PSS) was used as the hole transport layer. Aluminum (Al) and indium tin oxide (ITO) were served as device cathode and anode¡Arespectively, fabricated into a bi-layer structure of ITO/PEDOT:PSS/PBO/Al for electrical and luminescence responses. This research demonstrated an increase of current density and a decrease of threshold voltage with a decrease of PBO layer thickness from 90 nm to 27 nm to facilitate electron tunneling and electron-hole recombination. With a lower spin coating speed, polymer chain would aggregate and inter-penetrate resulted in red-shift of electroluminescence (EL) emission spectrum. Furthermore, micro-cavity effect might influence EL spectrum by varying layer thickness. Modulation of PBO layer thickness led to tunable EL emission color. It was also demonstrated that an increase of current density and a slightly decrease of threshold voltage with a PEDOT:PSS film thickness changing from 96 nm to 17 nm at a constant PBO layer thickness of 90 nm. Micro-cavity effect thus influenced EL emission for a tunable emission color. Photolithography was applied to obtain ITO substrate of grating depth of periodic variation and then coated with a PEDOT:PSS leading to a grated PEDOT:PSS layer of periodic thickness. This led to ITO/PEDOT:PSS/PBO/Al device showing broadened EL emission spectra.

No description available.