The bottleneck of forming small radius tube is that traditional processing methods can¡¦t effectively produce smaller bend radius tube in domestic industry now. First, this study will propose methods without mandrel, based on traditional bending way of rotary draw bending to form small bending radius tubes. This paper investigate results of traditional bending mode without mandrel in second part. By using finite element analysis, find the effects on wall-thinning, wall-thickening and ovility with different processing parameters. Also using the research results to obtain forming ranges. Through heating tubes we explore the possibility of hot forming of parameters and to find the impacts on bending tubes which heating under different parameters. We use the results above to find out the hot forming ranges. In heating and quenching of rotary draw bending experiments, we found that heating tubes under the same processing parameter can effectively enhance the formability and successfully derive better products of small radius bending tubes, to accomplish non-mandrel rotary bending process of small bending radius.

This thesis presented a sensor-less permanent magnet synchronous motor (PMSM) driver for controlling air-conditioner rotary compressor speed. In this thesis, a quasi-sine pulse-width modulation (PWM) driving method was proposed. Furthermore, the current feedback control scheme and rotor magnet pole position detection were included. The system structure was implemented by using a digital signal processing (DSP) platform. The proposed driving scheme was compared with the square-wave driving without current feedback and six-step square-wave driving method with current feedback. Moreover, the passive and shunt semi-active power factor correction (PFC) technique were researched for the air-conditioner application. Experimental results demonstrated that the system power factor could be improved by the proposed shunt semi-active PFC method. Besides, the proposed sensor-less quasi-sine PWM driving method implemented in an air-conditioner compressor driver was capable of reducing the magnitude of rotational speed ripples, compressor vibration, and system power consumption.

Finite volume method was employed for analyzing the three-dimensional turbulent flow structures, species distributions, and mixing behaviors of combustion flows in a rotary kiln under various operation conditions. The modified £e-£`turbulence model together with wall functions was adopted. Devolatilization of solid wastes were simulated by gaseous methane (CH4) non-uniformly distributed along the kiln bed. Combustion process was considered as a two-step reaction when primary air entered and mixed with methane gas in the first combustion chamber. Mixing-controlled eddy-dissipation model was employed for predicting the reaction rates of CH4, O2, CO2, CO and H2O. Effects of inleakage air, kiln rotation speed and methane distribution along the kiln bed were also examined. Results show that 128% excess air will get the best combustion efficiency, above which the combustion efficiency will decrease. The temperature and species are not uniformly distributed and are vertically stratified on cross-sectional plane. The combustion efficiency will also be lowered if there is inleakage airflow. Results also show rotation speed and methane distributions have little effect on combustion efficiency.

<p>Automobile and aero industries have an increasing interestin materials with improved mechanical properties. However, manyof these new materials are classified as difficult-to-cut withconventional tools. It is obvious that tools, cutting processesand cutting models has to be devel-oped parallel to materialsscience. In this thesis rotary cutting tools are tested as analternative toexpensive diamond or cubic bore nitridetools.</p><p>Metal matrix composites mostly consist of a light metalalloy (such as aluminium or titanium) reinforced with hard andabrasive ceramic parti-cles or fibres. On machining, thereinforcement results in a high rate of tool wear. This is themain problem for the machining of MMCs. Many factors affect thelife length of a tool, i.e. matrix alloy, type, size andfraction of the reinforcement, heat treatment, cuttingconditions and tool properties.</p><p>In tests, the Al-SiC MMC formed a deformation layer duringmilling, probably affected by lack of cooling. The dominatingfactor for tool life was the cutting speed. Water jet or CO2cooling of turning did not provide dramatic increase in toollife. With PCD, cutting speeds up to 2000 m/min were usedwithout machining problems and BUE formation. Tool flank wearwas abrasive and crater wear created an "orange-peel type" wearsurface. PCD inserts did not show the typical increase in flankwear rate at the end of its lifetime.</p><p>The use of self-propelled rotary tools seems to be apromising way to increase tool life. No BUE was formed on therotary tool at high cutting data. The measurements indicatethat the rotary tool creates twice as good surface as PCDtools. The longest tool life was gained with an inclinationangle of 10 degrees. Tool costs per component will beapproximately the same, but rotary cutting tool allows higherfeeds and therefore a higher production rate and thus a lowerproduction cost.</p><p>The rotary cutting operation might have a potential toincrease productiv-ity in bar peeling. The lack of BUE withrotary cutting gives hope on higher tool life. The test resultsshow that tool wear was 27% lower with rotary cutting tools.Increase of cutting speed from 22 to 44 m/min did not affectcutting forces. This indicates that the cutting speed canincrease without significant change in tool wear rate.</p><p>Issues related to rotary cutting like cutting models,cutting processes, standards, tools and models have beendiscussed. A tool wear model with kinetic energy has beendiscussed.</p><p><b>KEYWORDS:</b>Difficult-to-Cut material, Metal MatrixComposite (MMC), Machining, Machinability, Rotary Cutting Tool,Acoustic Emission</p>

2 pp. / Describes how to select the appropriate lawn mower to properly mow the species of grass at the correct height for high, medium, or low maintenance levels.

In 2006 resin accounted for approximately 17% of the direct manufacturing costs for oriented strand board (OSB). Because of their increased dependency on pMDI-resins, this percentage is likely greater for oriented strand lumber (OSL) and laminated strand lumber (LSL). The cost of PF- and pMDI-resins is expected to face upward pressure as the cost of their primary constituents, natural gas and crude oil, continue to reach new highs. Therefore, there is strong economic incentive to optimize the use of resin in the production of these three products. This can be accomplished by addressing two key issues: reducing resin wastage and optimizing resin distribution on the strands. Both issues will be overcome by focusing on the blending process, where resin is applied to the strands. This work focused on development and use of a discrete element model (DEM) for simulating strand flow in a rotary drum blender using the EDEM software package. EDEM required the input of three material and three interaction properties. Development of the model involved creating the simulated environment (i.e. physical dimensions) and assigning appropriate material and interaction properties given this environment and the assumptions that were made. This was accomplished in two steps, completing baseline bench-top experiments and a literature review to determine appropriate parameters and initial value ranges for these properties, and then fine-tuning these values based on a validation process. Using the validated model, an exploratory study was conducted to determine the effect of four blender design and operating parameters (flight height, number of flights, blender rotational speed, and blender fill level) on bulk strand flow. The results were analyzed with regards to overall trends and by focusing on two perspectives, end users and blender manufacturers. It was found that there was a strong relationship between these key parameters and bulk strand flow. These results suggest that operating parameters of a blender, namely rotational speed and tilt angle, should be linked directly to the blender feed rate to ensure an optimal blending environment is maintained. In addition, manufacturers of blenders must take into consideration the range in final operating conditions when designing and positioning flights.

The goal of the project was to enhance the period of weed growth prior to seeding in order to reduce weed emergence and weed competition after the crop has been planted. Weed growth was stimulated using either light tillage or by applying nitrogen fertilizer early in the spring. Light disturbance significantly increased pre-seed weed emergence while early applied nitrogen did not appear to have an effect. Post seeding weed emergence levels and weed biomass were similar among the light tillage and early nitrogen treatments. Therefore the goal of decreasing weed competition after seeding was not attained. Future research should focus on long-term strategies to reduce weed populations in field rather than seasonal strategies.

The goal of the project was to enhance the period of weed growth prior to seeding in order to reduce weed emergence and weed competition after the crop has been planted. Weed growth was stimulated using either light tillage or by applying nitrogen fertilizer early in the spring. Light disturbance significantly increased pre-seed weed emergence while early applied nitrogen did not appear to have an effect. Post seeding weed emergence levels and weed biomass were similar among the light tillage and early nitrogen treatments. Therefore the goal of decreasing weed competition after seeding was not attained. Future research should focus on long-term strategies to reduce weed populations in field rather than seasonal strategies.

In 2006 resin accounted for approximately 17% of the direct manufacturing costs for oriented strand board (OSB). Because of their increased dependency on pMDI-resins, this percentage is likely greater for oriented strand lumber (OSL) and laminated strand lumber (LSL). The cost of PF- and pMDI-resins is expected to face upward pressure as the cost of their primary constituents, natural gas and crude oil, continue to reach new highs. Therefore, there is strong economic incentive to optimize the use of resin in the production of these three products. This can be accomplished by addressing two key issues: reducing resin wastage and optimizing resin distribution on the strands. Both issues will be overcome by focusing on the blending process, where resin is applied to the strands. This work focused on development and use of a discrete element model (DEM) for simulating strand flow in a rotary drum blender using the EDEM software package. EDEM required the input of three material and three interaction properties. Development of the model involved creating the simulated environment (i.e. physical dimensions) and assigning appropriate material and interaction properties given this environment and the assumptions that were made. This was accomplished in two steps, completing baseline bench-top experiments and a literature review to determine appropriate parameters and initial value ranges for these properties, and then fine-tuning these values based on a validation process. Using the validated model, an exploratory study was conducted to determine the effect of four blender design and operating parameters (flight height, number of flights, blender rotational speed, and blender fill level) on bulk strand flow. The results were analyzed with regards to overall trends and by focusing on two perspectives, end users and blender manufacturers. It was found that there was a strong relationship between these key parameters and bulk strand flow. These results suggest that operating parameters of a blender, namely rotational speed and tilt angle, should be linked directly to the blender feed rate to ensure an optimal blending environment is maintained. In addition, manufacturers of blenders must take into consideration the range in final operating conditions when designing and positioning flights.

For the last two decades heart disease has been the highest single cause of death for the human population. With an alarming number of patients requiring heart transplant, and donations not able to satisfy the demand, treatment looks to mechanical alternatives. Rotary Ventricular Assist Devices, VADs, are miniature pumps which can be implanted alongside the heart to assist its pumping function. These constant flow devices are smaller, more efficient and promise a longer operational life than more traditional pulsatile VADs. The development of rotary VADs has focused on single pumps assisting the left ventricle only to supply blood for the body. In many patients however, failure of both ventricles demands that an additional pulsatile device be used to support the failing right ventricle. This condition renders them hospital bound while they wait for an unlikely heart donation. Reported attempts to use two rotary pumps to support both ventricles concurrently have warned of inherent haemodynamic instability. Poor balancing of the pumps’ flow rates quickly leads to vascular congestion increasing the risk of oedema and ventricular ‘suckdown’ occluding the inlet to the pump. This thesis introduces a novel Bi-Ventricular Assist Device (BiVAD) configuration where the pump outputs are passively balanced by vascular pressure. The BiVAD consists of two rotary pumps straddling the mechanical passive controller. Fluctuations in vascular pressure induce small deflections within both pumps adjusting their outputs allowing them to maintain arterial pressure. To optimise the passive controller’s interaction with the circulation, the controller’s dynamic response is optimised with a spring, mass, damper arrangement. This two part study presents a comprehensive assessment of the prototype’s ‘viability’ as a support device. Its ‘viability’ was considered based on its sensitivity to pathogenic haemodynamics and the ability of the passive response to maintain healthy circulation. The first part of the study is an experimental investigation where a prototype device was designed and built, and then tested in a pulsatile mock circulation loop. The BiVAD was subjected to a range of haemodynamic imbalances as well as a dynamic analysis to assess the functionality of the mechanical damper. The second part introduces the development of a numerical program to simulate human circulation supported by the passively controlled BiVAD. Both investigations showed that the prototype was able to mimic the native baroreceptor response. Simulating hypertension, poor flow balancing and subsequent ventricular failure during BiVAD support allowed the passive controller’s response to be assessed. Triggered by the resulting pressure imbalance, the controller responded by passively adjusting the VAD outputs in order to maintain healthy arterial pressures. This baroreceptor-like response demonstrated the inherent stability of the auto regulating BiVAD prototype. Simulating pulmonary hypertension in the more observable numerical model, however, revealed a serious issue with the passive response. The subsequent decrease in venous return into the left heart went unnoticed by the passive controller. Meanwhile the coupled nature of the passive response not only decreased RVAD output to reduce pulmonary arterial pressure, but it also increased LVAD output. Consequently, the LVAD increased fluid evacuation from the left ventricle, LV, and so actually accelerated the onset of LV collapse. It was concluded that despite the inherently stable baroreceptor-like response of the passive controller, its lack of sensitivity to venous return made it unviable in its present configuration. The study revealed a number of other important findings. Perhaps the most significant was that the reduced pulse experienced during constant flow support unbalanced the ratio of effective resistances of both vascular circuits. Even during steady rotary support therefore, the resulting ventricle volume imbalance increased the likelihood of suckdown. Additionally, mechanical damping of the passive controller’s response successfully filtered out pressure fluctuations from residual ventricular function. Finally, the importance of recognising inertial contributions to blood flow in the atria and ventricles in a numerical simulation were highlighted. This thesis documents the first attempt to create a fully auto regulated rotary cardiac assist device. Initial results encourage development of an inlet configuration sensitive to low flow such as collapsible inlet cannulae. Combining this with the existing baroreceptor-like response of the passive controller will render a highly stable passively controlled BiVAD configuration. The prototype controller’s passive interaction with the vasculature is a significant step towards a highly stable new generation of artificial heart.