<p><p>This paper is the result of a master thesis project on helicopter rotor downwash effects using computational fluid dynamics (CFD). The work was performed at the department of Aerodynamics and Flight Mechanics at Saab AB, Linköping in 2008. It completes the author’s studies for a M.Sc degree in Applied Physics and Electrical Engineering at the Department of Electrical Engineering at the Linköping institute of technology (LiTH), Linköping, Sweden.</p><p> </p><p>The aim of the project was to study the rotor downwash effects and its influence on the helicopter fuselage. To fulfil this purpose, several CFD calculations were carried out and the aerodynamic forces and moments resulting from the calculations were implemented in an existing simulation model, developed in-house at Saab. The original (existing) model was compared to the updated model by studying step responses in MATLAB, Simulink. For some step commands, the comparisions indicated that the updated model was more damped in yaw compared to the original model for the hovering helicopter. When the helicopter was trimmed for a steady turn, the states in the updated model diverged much faster than the states in the original model for any given step command.</p><p> </p><p> </p><p>In order to investigate the differences between the original helicopter model and the updated model from a controlling perspective, a linear quadratic (LQ) state feedback controller was synthesized to stabilize the vehicle in a steady turn. The LQ method was chosen as it is a modern design technique with good robustness and sensitivity properties and since it is easily implemented in MATLAB.  Before synthesising, a simplification of the helicopter model was made by reducing states and splitting them into lateral and longitudinal ones. Step responses from simulations with the original and the updated model were studied, showing an almost identical behavior.</p><p> </p><p>It can be concluded that the aerodynamic coefficients obtained from the CFD calculations can be used for determining the aerodynamic characteristics of the helicopter. Some further validation is needed though, for example by comparing the results with flight test data. In order to build an aerodynamic data base that covers the whole flight envelop, additional CFD calculations are required.</p><p> </p></p>

This paper is the result of a master thesis project on helicopter rotor downwash effects using computational fluid dynamics (CFD). The work was performed at the department of Aerodynamics and Flight Mechanics at Saab AB, Linköping in 2008. It completes the author’s studies for a M.Sc degree in Applied Physics and Electrical Engineering at the Department of Electrical Engineering at the Linköping institute of technology (LiTH), Linköping, Sweden.   The aim of the project was to study the rotor downwash effects and its influence on the helicopter fuselage. To fulfil this purpose, several CFD calculations were carried out and the aerodynamic forces and moments resulting from the calculations were implemented in an existing simulation model, developed in-house at Saab. The original (existing) model was compared to the updated model by studying step responses in MATLAB, Simulink. For some step commands, the comparisions indicated that the updated model was more damped in yaw compared to the original model for the hovering helicopter. When the helicopter was trimmed for a steady turn, the states in the updated model diverged much faster than the states in the original model for any given step command.     In order to investigate the differences between the original helicopter model and the updated model from a controlling perspective, a linear quadratic (LQ) state feedback controller was synthesized to stabilize the vehicle in a steady turn. The LQ method was chosen as it is a modern design technique with good robustness and sensitivity properties and since it is easily implemented in MATLAB.  Before synthesising, a simplification of the helicopter model was made by reducing states and splitting them into lateral and longitudinal ones. Step responses from simulations with the original and the updated model were studied, showing an almost identical behavior.   It can be concluded that the aerodynamic coefficients obtained from the CFD calculations can be used for determining the aerodynamic characteristics of the helicopter. Some further validation is needed though, for example by comparing the results with flight test data. In order to build an aerodynamic data base that covers the whole flight envelop, additional CFD calculations are required.

The resolution of the complex physics of rotating configurations is critical for any engineering analysis that requires multiple frames of reference. Two well-known applications are in the rotorcraft and wind energy industries. Rotor wake impingement from rotor-fuselage and wind turbine-tower interactions impact structural and acoustic characteristics. Additionally, parasite drag resulting from rotorcraft hubs may result in severe limitations on forward flight vehicle performance. Complex turbulent wakes from rotors and hubs impinging on downstream empennage can create adverse aeroelastic behavior and can affect handling qualities. Numerical simulations of these flows require state-of-the-art Navier Stokes methods using dynamic overset grids. However, many current methods typically used in industry result in wakes that dissipate essential features. In order to address these concerns, two advancements are introduced in this thesis. Feature-based grid adaptation on dynamic overset grids has been developed and demonstrated with an unstructured Navier Stokes solver. The unique feature of the adaptation technique is that it is applied globally on the overset grid system except within the boundary layer. In concert with grid adaptation, an efficient parallelized search algorithm for solution interpolation over massively distributed systems has been created. This results in cost-effective interpolation that retains the numerical order of accuracy and has been verified in both space and time. The improvements have been demonstrated for rotor-fuselage interaction and a generic rotating hub. Detailed analysis of convergence of the methodology and sensitivity of the results to relevant parameters have also been included.