Le graphène héberge un gaz d'électrons bi-dimensionnel, sujet à un potentiel électrostatique désordonné dû aux impuretés de charge dans le substrat. Ce potentiel désordonné induit des inhomogénéités de la densité de porteurs de charge dans le graphène. Par ailleurs, l'écrantage dans le graphène mono-feuillet de ce potentiel dépend lui-même de la densité de porteurs de charge. L'effet du désordre de charge peut donc être modulé avec un potentiel de grille global, ce qui se manifeste en particulier dans la transconductance de dispositifs à base de graphène. Nous combinons des mesures par Microscopie/Spectroscopie à effet tunnel avec des mesures de transport in situ sur des dispositifs à base de mono-feuillets de graphène sur SiO2, à basse température. Les cartes de la densité locale d'états du graphène, à diverses tensions de grille, mettent en évidence l'augmentation progressive des dimensions latérales ainsi que de l'amplitude des inhomogénéités au voisinage du point de Dirac. Alors que la dépendance en grille de la taille des inhomogénéités est en bon accord avec les prédictions, leur amplitude est plus forte qu'attendue au point de Dirac. Nous expliquons ce désaccord en prenant en compte l'effet de grille local produit par la pointe elle-même, qui a pour effet d'amplifier expérimentalement toute variation de la densité de porteurs de charge lorsque celle-ci elle faible. Cette expérience est ainsi la première mesure qui relie quantitativement les propriétés de désordre de charge à l'échelle microscopique aux propriétés de transport macroscopiques d'un dispositif à base de graphène. / Graphene presents a two-dimensional system whose charge carriers are subjected to a disordered potential created by random charge impurities trapped in the substrate. This impurity potential induces an inhomogeneous carrier concentration. On the other hand, the ability of single-layered graphene to screen this potential strongly depends on the charge carrier density. Thus the effect of the resulting charge disorder can be tuned with the backgate which manifests also in the transport properties of the device. By combining Scanning tunneling microscopy and spectroscopy with in-situ transport at dilution temperature, we probe a system of single-layered graphene on SiO2. Local density of states maps on graphene, acquired at various carrier concentrations show gradual increase of spatial extent and amplitude of inhomogeneities as the Dirac point is approached. While the variations of the spatial extent of the fluctuations with back-gate show very good agreement with predictions, the observed amplitude of inhomogeneities show a larger than expected increase at low densities. We explain this as a result of the local gating effect exerted by the tip on graphene which amplifies any change in the intrinsic doping at low carrier concentrations. This is the first experiment bridging the gap between microscopic disorder and macroscopic transport properties of a graphene device.

Ce travail s’inscrit dans le contexte des microscopies optiques à très haute résolution. Nous proposons un nouveau concept de sonde active pour la microscopie optique en champ proche (SNOM), exploitant les effets de génération de second harmonique (SHG) de molécules. L’idée développée vise à s'affranchir de l’une des principales limitations des sondes actives fluorescentes réalisées jusqu'à présent : l'accrochage des sondes à l'extrémité de la pointe SNOM, étape toujours délicate et souvent peu fiable. Pour ce faire, nous avons mis en œuvre une technique qui consiste à utiliser la localisation du champ électrique au sein d’une jonction pointe métallique-substrat conducteur immergée dans une solution de molécules non-linéaires dipolaires. L’interaction champ-molécules entraine l’orientation locale un nano-volume de ces molécules dont l’excitation par un laser permet ensuite la génération d’un signal de second harmonique. Après avoir validé ce concept dit de « nano-EFISHG » (Electric Field Induced SHG) nous avons conçu un nouveau banc expérimental, dédié à l'imagerie de second harmonique haute résolution : celui-ci a permis d'obtenir les premières images présentant un contraste de second harmonique sur un échantillon structuré à l'échelle micronique.Nous avons ensuite travaillé à l’optimisation de la résolution de l’expérience mise en place : nous avons notamment démontré la possibilité de tirer parti d’effets d’exaltation locale du champ électromagnétique se produisant à l'extrémité de pointes ou de nano-objets métalliques. L’extrapolation des résultats obtenus montre que de telles exaltations devraient permettre d’atteindre des résolutions de l’ordre de 50 nm. / This work was achieved within the context of high resolution optical microscopy. We propose a new concept of active probe for near-field optical microscopy (SNOM), exploiting the effect of second harmonic generation (SHG) of molecules. The idea intends to avoid one of the main limitations of currently developed fluorescent active probes: the anchoring of the probes at the end of a SNOM tip which is a very delicate and often unreliable step. The technique implemented here consists in using the electric field localization in a metallic tip – conducting substrate junction immersed in a solution containing dipolar non-linear molecules. The interaction between the molecules and the electric field gives rise to the local orientation of a nano-volume of these molecules whose excitation by a laser allows generation of a second harmonic signal.After validation of this concept named as “nanoEFISHG” (Electric Field Induced SHG) we have designed a new experimental setup, dedicated to high resolution second harmonic imaging. Successful implementation of this setup has leaded to the recording of the first images presenting a second harmonic contrast on a sample structured at the micronic scale. Next step has consisted in working towards optimization of the experimental resolution: we have especially study the possibility of taking advantages of local field enhancement effects occurring at metallic nano-structures or sharp tip’s apex. The extrapolation of the obtained results shows that such effects should allow to reach resolutions about 50 nm.

Skyrmions are spin textures with particle character that order themselves into so-called “skyrmion lattices” (SkLs). A skyrmion is topologically nontrivial, which adds stability against external perturbations and attracts tremendous interest from the theoretical side. Since skyrmions can be moved with small electrical currents, they are being discussed for novel spintronic applications, such as racetrack memory. Further interest has been spurred by the discovery of multiferroic compounds that also host SkLs, resulting in additional properties that are highly interesting both for applications and for fundamental research. The scope of this thesis encompasses the investigation of two completely different exemplary SkL-hosting multiferroic systems using a broad set of scanning probe microscopy techniques. These can probe multiple properties on a local scale in real space with a single measurement, examining details not resolved by non-local techniques. In the first part, there is a brief introduction to magnetic skyrmions and scanning probe microscopy with a short review of the theoretical background. The materials of interest and their known properties are then introduced. These are Cu2OSeO3, an insulator exhibiting the emergence of Bloch-type skyrmions as well as type-II multiferroicity, and the lacunar spinel chalcogenides, which were recently found to exhibit multiferroic Néel-type skyrmions pinned to magnetic easy-axes/planes together with type-I multiferroicity originating from a structural Jahn–Teller transition. The second part first presents various scanning probe studies and their results for Cu2OSeO3, where, aside from the magnetic textures of the various magnetic phases, the magnetoelectric effect and the magnetic phase transitions are investigated and described with basic theoretical models. Results show a good correlation between observations and theory, as well as with other experimental methods. Various lacunar spinels are then investigated, mostly GaV4S8 and GaMo4S8. Observation of the structural phase transition leads to the observation of {100}-type domain boundaries compatible with the compatibility critera based on crystal geometry. Furthermore, measurements of the magnetic textures of the different magnetic phases for GaV4S8 are presented and analysed. Results highlight a pinning of the pitch vector to the magnetic hard plane, and that the structural domain boundaries are by necessity magnetic domain boundaries. Analysing the influence of surface anisotropy and structural domain boundaries reveals a strong effect of both on the formation of magnetic patterns in their vicinity. Finally, the magnetoelectric effect of different lacunar spinels is investigated by measuring the surface potential with changing magnetic fields leading to a hysteretic behaviour in all materials.:Abstract/Kurzdarstellung 1 Introduction – Skyrmions meet Multiferroicity 2 Magnetic Skyrmion Lattices 2.1 What is a Skyrmion? 2.2 Formation of Skyrmion Lattices 2.2.1 Basic Considerations 2.2.2 Emergence of Skyrmion Lattices 2.3 General Properties of Skyrmions 2.4 Ways to Observe Skyrmions 3 Scanning Probe Microscopy 3.1 General Aspects 3.2 SPM in Contact Mode 3.2.1 Atomic Force Microscopy 3.2.2 Conductive Atomic Force Microscopy 3.2.3 Piezoresponse Force Microscopy 3.3 SPM in Non-Contact Mode 3.3.1 Atomic Force Microscopy 3.3.2 Kelvin Probe Force Microscopy 3.3.3 Magnetic Force Microscopy 3.4 About Scanning Dissipation Microscopy 3.4.1 Possible Origins of Dissipation 3.4.2 Measuring Dissipation 3.4.3 Mathematical Background 3.5 Experimental Setup 4 Investigated Materials 4.1 Cubic copper(II)-oxo-selenite Cu2O(SeO3) 4.2 Lacunar Spinel Chalcogenides 4.2.1 General Aspects and Materials Chosen 4.2.2 Structural Phase Transition and Expected Piezoresponse 4.2.3 Magnetic Phase Transition 4.2.4 Investigated Crystals 5 Investigations on Cu2OSeO3 5.1 Observing the Different Magnetic Phases 5.1.1 Analysis of Magnetic Textures with Magnetic Force Microscopy 5.1.2 Analysis of Magnetic Textures with Scanning Dissipation Microscopy 5.2 Analysis of the Magnetoelectric Effect 5.2.1 Observing the Magnetoelectric Effect with KPFM 5.2.2 Heuristic Description of the Magnetoelectric Effect 5.3 Analysing the Magnetic Phase Transitions with SPM 5.3.1 Motivation from Theory 5.3.2 Distinguishing the Helical, Conical and Field-Polarised Phases 5.3.3 The Helical–Conical Phase Transition 5.3.4 Passing through the Conical Phase 6 Investigations on GaV4S8 6.1 Observing the Structural Phase Transition 6.1.1 Results from nc-AFM 6.1.2 Results from ct-AFM and PFM 6.2 Observing the Magnetic Phases 6.3 Analysing the Magnetic SDM Images 6.3.1 Theoretical Considerations 6.3.2 Rescaling from the Measured to the Magnetic Hard Plane 6.3.3 Influence of the Surface on the Patterns Observed 6.4 Influence of Structural Domain Walls on Magnetic Patterns 7 Further Investigation on Lacunar Spinels 7.1 Investigations on GaMo4S8 7.1.1 Experimental Results 7.1.2 Theoretical Considerations 7.1.3 Evaluation of the Experimental Data 7.2 Magnetoelectric Effect of Lacunar Spinels 8 Remarks About Magnetic Non-Contact Dissipation 9 Summary and Outlook 9.1 Synopsis 9.2 Outlook – Probing the Future A Permissions For Usage of Content B Some Additional Information on Non-Contact Dissipation C Bonus Images Bibliography Publications Acknowledgements Erklärung / Skyrmionen sind teilchenartige Spintexturen, welche sich in sogenannten Skyrmionengittern anordnen. Jedes Skyrmion besitzt eine topologische Ladung. Dieses Konzept ist von bedeutendem Interesse für die Theorie und führt zu zusätzlicher Stabilität gegen externe Störungen. Da Skyrmionen mit geringen elektrischen Strömen bewegt werden können, sind sie auch Kanditaten für neuartige, spintronische Anwendungen wie den Racetrack-Speicher. Zusätzlich wurden vor einiger Zeit multiferroische Materialien entdeckt, welche ebenso Skyrmionengitter bilden und aufgrund dessen weitere, interessante Eigenschaften besitzen, welche sowohl für Anwendungen als auch für die Grundlagenforschung interessant sind. Inhalt dieser Dissertation ist die Untersuchung zweier verschiedener, exemplarischer multiferroischer Materialien mit Skyrmiongitterphasen mittels verschiedener Rastersondentechniken. Dies erlaubt das gleichzeitige Erfassen mehrerer Parameter auf einer lokalen Skala im Realraum mit einer einzigen Messung und somit die Untersuchung von Details, welche durch nicht-lokale Techniken nicht erfasst werden können. Im ersten Teil wird eine kurze Einleitung über magnetische Skyrmionen und die Rastersondenmikroskopie sowie Abrisse über deren theoretischen Hintergrund gegeben. Im Anschluß werden die untersuchten Materialien und deren Eigenschaften vorgestellt. Das erste System ist Cu2OSeO3, ein Isolator, welcher Bloch-artige Skyrmionengitter formiert und ein Typ-II Multiferroikum ist. Weitere Systeme gehören zur Klasse der lakunären Spinell-Chalkogenide, welche nach neuesten Erkenntnissen multiferroische Néel-artige Skyrmionen formieren, deren Modulationsvektor zur magnetisch harten Achse/Ebene fixiert ist. Ebenso sind diese aufgrund eines strukturellen Jahn-Teller Überganges Typ-I Multiferroika. Im zweiten Teil werden verschiedene Rastersondenuntersuchungen und ihre Ergebnisse präsentiert. Beginnend mit Cu2OSeO3, werden, neben den den magnetische Texturen der verschiedenen magnetischen Phasen, der magnetoelektrische Effekt und der helisch-konische Phasenübergang untersucht sowie mit grundlegenden theoretischen Modellen verglichen. Die Ergebnisse zeigen eine gute Übereinstimmung zwischen den Beobachtungen und der Theorie sowie mit anderen Meßmethoden. Im Anschluß werden verschiedene lakunäre Spinell-Chalkogenide, vor allem GaV4S8 und GaMo4S8, untersucht. Beobachtungen des strukturellen Phasenüberganges ergeben die Formierung von {100}-artigen Domänenwänden, welche mit den Vorhersagen der Kompatibilitätskriterien resultierend aus der Kristallgeometrie übereinstimmen. Des Weiteren werden Messungen der magnetischen Texturen der verschiedenen magnetischen Phasen von GaV4S8 präsentiert sowie analysiert. Die Ergebnisse heben hervor, daß der Modulationsvektor an der magnetisch harten Ebene fixiert ist und daß die strukturellen Domänengrenzen notwendigerweise auch die magnetischen Domänengrenzen sein müssen. Eine Analyse des Einflusses der Oberflächenanisotropie sowie der strukturellen Domänengrenzen zeigt eine starke Wirkung beider auf die Formierung magnetischer Texturen in ihrer Nähe. Schließlich wird der magnetoelektrische Effekt der lakunären Spinell-Chalkogenide durch Messung des Oberflächenpotentiales als Funktion des angelegten Magnetfeldes untersucht. Beobachtungen ergeben ein hysteretisches Verhalten in allen Materialen.:Abstract/Kurzdarstellung 1 Introduction – Skyrmions meet Multiferroicity 2 Magnetic Skyrmion Lattices 2.1 What is a Skyrmion? 2.2 Formation of Skyrmion Lattices 2.2.1 Basic Considerations 2.2.2 Emergence of Skyrmion Lattices 2.3 General Properties of Skyrmions 2.4 Ways to Observe Skyrmions 3 Scanning Probe Microscopy 3.1 General Aspects 3.2 SPM in Contact Mode 3.2.1 Atomic Force Microscopy 3.2.2 Conductive Atomic Force Microscopy 3.2.3 Piezoresponse Force Microscopy 3.3 SPM in Non-Contact Mode 3.3.1 Atomic Force Microscopy 3.3.2 Kelvin Probe Force Microscopy 3.3.3 Magnetic Force Microscopy 3.4 About Scanning Dissipation Microscopy 3.4.1 Possible Origins of Dissipation 3.4.2 Measuring Dissipation 3.4.3 Mathematical Background 3.5 Experimental Setup 4 Investigated Materials 4.1 Cubic copper(II)-oxo-selenite Cu2O(SeO3) 4.2 Lacunar Spinel Chalcogenides 4.2.1 General Aspects and Materials Chosen 4.2.2 Structural Phase Transition and Expected Piezoresponse 4.2.3 Magnetic Phase Transition 4.2.4 Investigated Crystals 5 Investigations on Cu2OSeO3 5.1 Observing the Different Magnetic Phases 5.1.1 Analysis of Magnetic Textures with Magnetic Force Microscopy 5.1.2 Analysis of Magnetic Textures with Scanning Dissipation Microscopy 5.2 Analysis of the Magnetoelectric Effect 5.2.1 Observing the Magnetoelectric Effect with KPFM 5.2.2 Heuristic Description of the Magnetoelectric Effect 5.3 Analysing the Magnetic Phase Transitions with SPM 5.3.1 Motivation from Theory 5.3.2 Distinguishing the Helical, Conical and Field-Polarised Phases 5.3.3 The Helical–Conical Phase Transition 5.3.4 Passing through the Conical Phase 6 Investigations on GaV4S8 6.1 Observing the Structural Phase Transition 6.1.1 Results from nc-AFM 6.1.2 Results from ct-AFM and PFM 6.2 Observing the Magnetic Phases 6.3 Analysing the Magnetic SDM Images 6.3.1 Theoretical Considerations 6.3.2 Rescaling from the Measured to the Magnetic Hard Plane 6.3.3 Influence of the Surface on the Patterns Observed 6.4 Influence of Structural Domain Walls on Magnetic Patterns 7 Further Investigation on Lacunar Spinels 7.1 Investigations on GaMo4S8 7.1.1 Experimental Results 7.1.2 Theoretical Considerations 7.1.3 Evaluation of the Experimental Data 7.2 Magnetoelectric Effect of Lacunar Spinels 8 Remarks About Magnetic Non-Contact Dissipation 9 Summary and Outlook 9.1 Synopsis 9.2 Outlook – Probing the Future A Permissions For Usage of Content B Some Additional Information on Non-Contact Dissipation C Bonus Images Bibliography Publications Acknowledgements Erklärung

A remote-sensing acoustic method for implementing position control feedback in Scanning Probe Microscopy (SPM) is presented. The capabilities of this feedback control using the new Whispering Gallery Acoustic Sensing (WGAS) method is demonstrated in a Shear-force Scanning Probe Microscope that uses a sharp probe attached to a piezoelectric Quartz Tuning Fork (QTF) firmly mounted on the microscope's frame. As the QTF is electrically driven its mechanical response reaches the SPM frame which then acts as a resonant cavity producing acoustic modes measured with an acoustic sensor strategically placed on the SPM head. The novelty of the WGAS resides in using an SPM frame with a perimeter closely matching the intervening acoustic wavelength to act as a resonant cavity. The whispering gallery cavity constitutes an acoustic amplifier for the mechanical motion of the QTF probe. The observed monotonic behavior of the whispering gallery acoustic signal as a function of the probe sample distance is exploited here for tip-sample distance control with nanometer sensitivity, thus allowing topographic characterization as the probe is scanned across the sample's surface. This thesis includes a description of a Labview based programming for the Field Programmable Gate Array (FPGA) card used in the automated control of the WGAS feedback microscope, a solution for improving the effective resolution of the Digital to Analog Converter (DAC) and initial results towards theoretically modeling the WGAS working principle.

The thesis is aimed at the characterization of carbon nanotubes and silver nanowires by Scanning Probe Microscopy, namely Scanning Tunneling Microscopy (STM), Atomic Force Microscopy (AFM), Conductive AFM (CAFM) and Scanning Near-Field Optical Microscopy (SNOM). Carbon nanotubes were analyzed by STM, AFM and CAFM microscopy. In a designed apparatus the silver nanowires were fabricated by template assisted deposition and were analyzed with respect to their geometry (AFM), local conductivity (CAFM) and optical properties (SNOM, microreflex spectroscopy). It was found that preferential type of carbon nanowires depends on the fabrication process. The measurements of local conductivity of the nanotubes revealed the similarity with the STM measurements. The AFM measurements of silver nanowires confirmed their growth inside the pores of polycarbonate template. Single nanowires exhibits the semiconducting behavior according to I--V measurement and localized plasmon resonances.

No description available.

The work of this thesis comprises extensive Noncontact Atomic Force Microscopy (NC-AFM) characterization of clean metal-oxide (YSZ(100)/(111) and MgO(100)) and graphitic (HOPG) supports as templates for the novel, photochemically induced nucleation of cobalt oxide nanostructures, particularly Cobalt (III) Oxide. The nanostructure-support surfaces were also studied by X-ray Photoelectron Spectroscopy (XPS) to verify the nature of the supported cobalt oxide and to corroborate the surface topographic and phase NC-AFM data. Heteroepitaxial growth of Co2O3 nanostructures proves to exhibit a variety of different growth modes based on the structure of the support surface. On this basis, single-crystal support surfaces ranging from nonpolar to polar and atomically flat to highly defective and reactive were chosen, again, yielding numerous substrate-nanostructure interactions that could be probed by high-performance surface science techniques.

The thesis focuses on the development of instruments used for surfaces and nanostructures characterization. Individual techniques of scanning probe microscopy provide different information of the sample surface. The resolution of scanning probe microscopy, providing 3D topography information, reaches subnanometer values or even an atomic level. Therefore, the scanning probe microscopy is one of the most employed method in the field of nanotechnology. The thesis describes the details of development of two scanning probe microscopes intended for measurement under ultra high vacuum conditions. As for the first one, many changes were proposed leading to its better variability, extended functionality and increased user comfort. The second microscope is being design with the aim of its combination with other analytic techniques, especially with scanning electron microscopy. An integral part of scanning probe microscopes is a precise positioning system for navigation of the probe to the selected site. Therefore, the thesis also deals with the development of linear piezoceramic actuators used not only in the ultra high vacuum compatible microscopes but also as a general purpose nanomanipulators.

Les microscopes en champ proche permettent d'obtenir la topographie d'un échantillon avec une résolution pouvant atteindre la résolution atomique. Les spectroscopies de rayons-X sont des méthodes de caractérisation qui permettent de déterminer la composition et la structure élémentaire de l'échantillon avec une précision inférieure à l'Ångström. Nous avons choisi de coupler ces deux techniques en collectant localement la luminescence visible issue de l'échantillon par la pointe-sonde d'un microscope à force de cisaillement, constituée d'une fibre optique effilée de faible ouverture. Cette technique a été utilisée pour caractériser des échantillons semiconducteurs micro- et nano-structurés afin d'en obtenir simultanément la topographie et la cartographie de luminescence locale. Afin de pouvoir étendre ce concept à d'autres types de matériaux, la faisabilité de la collecte de la fluorescence X locale a été évaluée avec la microsource. Pour cela la fluorescence X émise par un échantillon a été collectée par un capillaire cylindrique équipant un détecteur EDX. L'influence du diamètre du capillaire sur le niveau de signal a été mesurée. Une simulation numérique a été développée afin d'estimer le niveau de signal obtenu en utilisant un capillaire de 1 µm de diamètre et d'optimiser la géométrie du système. En couplant la microscopie en champ proche et l'analyse XRF, à la lumière de ces résultats, il sera possible d'atteindre 100 nm de résolution latérale en environnement synchrotron et moins de 1 µm à l'aide d'une source de laboratoire. Il serait alors possible de sélectionner un objet particulier sur une surface et d'en faire l'analyse élémentaire. / Scanning Probe Microscopes allow to obtain sample topography up to atomic resolution. X-ray spectroscopies allow elemental and structural analysis of a sample with accuracy better than 1 Å. The lateral resolution is limited by the primary beam diameter, currently a few µm². We have chosen to couple this two technics. Local sample visible luminescence is collected through a low aperture sharp optical fibre, probe of a shear force microscope. This technique was used to characterize microstructured semiconducting samples to achieve simultaneously the surface topography and luminescence mapping. The results were obtained using either synchrotron radiation or a laboratory microsource equipped with a polycapillary lens. To extend this concept to a wider variety of materials, local XRF collection by an EDX detector equipped with a cylindrical X-ray capillary was tested. A cobalt sample irradiated with the microsource was used for technique evaluation. The signal magnitude dependence with the capillary diameter was measured. Modelling and numerical calculations were developed to estimate the signal magnitude that could be detected using a 1 µm diameter capillary. The optimal system geometry was determined. Scanning Probe Microscopy combined to XRF analysis could thereby lead to simultaneous acquisition of sample topography and chemical mapping. The expected lateral resolution using synchrotron radiation is 100 nm while sub 1 µm resolution is realistic with a laboratory source. This technique would allow to point a peculiar micro- or nano-object on the surface and to perform its chemical analysis.

In dieser Dissertation wird die Selbstorganisation von pi-konjugierten (makro)molekularen Architekturen durch Chemisorption oder Physisorption in hochgeordnete supramolekulare nanoskopische und mikroskopische Strukturen auf festen Trägern untersucht. Ihre Struktur und Dynamik wurden auf molekularer Skala hauptsächlich mit Rastersondenmikroskopien, insbesondere mit Rastertunnel- und Rasterkraftmikroskopie, untersucht. Dies erlaubte die Charakterisierung einer Reihe von Phänomenen, die sowohl an Fest-Flüssig-Grenzflächen auftreten, wie beispielsweise die Dynamik der einzelnen molekularen Nanostäbchen (Ostwald Reifung) und die Fraktionierung steifer Polymerstäbchen durch Physisorption an der Grafitoberfläche aus der Lösung heraus, als auch in trockenen Filmen vorkommen wie die Selbstorganisation steifer Polymerstäbchen zu Nanobändern mit molekularen Querschnitten, die sich epitaktisch auf Oberflächen orientieren lassen und auch die Ausbildung gestapelter Architekturen von diskförmigen Molekülen. Außerdem wurden die elektronischen Eigenschaften der untersuchten Systeme mit Hilfe von Photoelektronenspektroskopie charakterisiert. Die entwickelten Nanostrukturen sind nicht nur für Nanokonstruktionen auf festen Oberflächen von Interesse, sondern besitzen auch Eigenschaften, die sie für Anwendungen in einer zukünftigen molekularen Elektronik prädestiniert, etwa für den Aufbau molekularer Drähte. / In this thesis the self-assembly of pi-conjugated (macro)molecular architectures, either through chemisorption or via physisorption, into highly ordered supramolecular nanoscopic and microscopic structures has been studied. On solid substrates structure and dynamics has been investigated on the molecular scale making use primarily of Scanning Probe Microscopies, in particular Scanning Tunneling Microscopy and Scanning Force Microscopy. This allowed to characterize a variety of phenomena occurring both at the solid-liquid interface, such as the dynamics of the single molecular nanorods (known as Ostwald ripening), the fractionation of a solution of rigid-rod polymers upon physisorption on graphite; and in dry films, i.e. the self-assembly of rigid-rod polymers into nanoribbons with molecular cross sections which can be epitaxially oriented at surfaces and the formation ordered layered architectures of disc-like molecules. In addition the electronic properties of the investigated moieties have been studied by means of Photoelectron Spectroscopies. The nanostructures that have been developed are not only of interest for nanoconstructions on solid surfaces, but also exhibit properties that render them candidates for applications in the field of molecular electronics, in particular for building molecular nanowire devices.