No / Polymer extrusion is fundamental to the processing of polymeric materials and melt flow temperature homogeneity is a major factor which influences product quality. Undesirable thermal conditions can cause problems such as melt degradation, dimensional instability, weaknesses in mechanical/optical/geometrical properties, and so forth. It has been revealed that melt temperature varies with time and with radial position across the die. However, the majority of polymer processes use only single-point techniques whose thermal measurements are limited to the single point at which they are fixed. Therefore, it is impossible for such techniques to determine thermal homogeneity across the melt flow. In this work, an extensive investigation was carried out into melt flow thermal behavior of the output of a single extruder with different polymers and screw geometries over a wide range of processing conditions. Melt temperature profiles of the process output were observed using a thermocouple mesh placed in the flow and results confirmed that the melt flow thermal behavior is different at different radial positions. The uniformity of temperature across the melt flow deteriorated considerably with increase in screw rotational speed while it was also shown to be dependent on process settings, screw geometry, and material properties. Moreover, it appears that the effects of the material, machine, and process settings on the quantity and quality of the process output are heavily coupled with each other and this may cause the process to be difficult to predict and variable in nature. (C) 2013 Society of Plastics Engineers

No / Polymer extrusion is an energy intensive process, which is often run at less than optimal conditions. The extrusion process consists of gradual melting of solid polymer by thermal conduction and viscous shearing between a rotating screw and a barrel; as such it is highly dependent upon the frictional, thermal and rheological properties of the polymer. Extruder screw geometry and extrusion variables should ideally be tailored to suit the properties of individual polymers, but in practice this is rarely achieved due to the lack of understanding of the process. Here, in-process monitoring techniques have been used to characterise the thermal dynamics of the extrusion process. Novel thermocouple grid sensors have been used to measure melt temperature fields within flowing polymer melts at the entrance to an extruder die in conjunction with infra-red thermometers and real-time quantification of energy consumption. A commercial grade of polyethylene has been examined using three extruder screw geometries at different extrusion operating conditions to understand the process efficiency. Extruder screw geometry, screw rotation speed and set temperature were found to have a significant effect on the thermal homogeneity of the melt and process energy consumed. (C) 2012 Elsevier Ltd. All rights reserved.

Large format 3D printing of thermoplastic polymers is a fast growing technology for industrial tools manufacturing and enables the production of meters long workpiece in a fraction of time, material and cost than conventional subtractive solutions. Due to the scale and timing imposed by the industry, Large Format Additive Manufacturing (LFAM) is mostly based on screw extrusion of thermoplastic pellets offering a significantly higher deposition rate and lower material costs compared to the well-known filament extrusion 3D printing (FFF). Carbon fiber reinforced polymers are commonly used in large-scale 3D printing as they minimize distortions and internal stresses during deposition preventing delamination and failure of the printed component. The technology stands out for the exceptional melt deposition rate; the lack of a temperature-controlled build chamber, and the low surface-to-volume proportion of the printed strand, making the temperature management of the deposited material particularly challenging in large-scale 3D printing. Print overcooling may lead to poor adhesion between layers eventually resulting in delamination, excessive heat build-up, on the other hand, is likely to result in sagging and print failure. Print thermal behavior and temperature management are closely related to material, part design and deposition strategy. Even though numerous software solutions for predictive process simulation as well as active feedback print controls for parameters optimization are emerging, common practice still relies on restricted set of strategies deduced by trial and error testing sessions; the best printing configuration is specifically custom-made for each print, an approach that could severely hinder the technology potential. This research is conducted as part of the project of CMS S.p.a., a company specialized in the production of CNC multi-axis machining centers, to develop and market an all-around tool manufacturing solution that would combine milling and Screw Extrusion Additive Manufacturing (SEAM). The study aims to develop a flexible and versatile cooling model that can predict the best process window for large-scale additive manufactured parts and automatically generate the best printing parameters for a generic printing strategy according to part material and shape. Next, the model was incorporated inside a path generation slicing software that operates with the same process parameters, unique solution on the market. Any given material is described by a specific set of variables that can be experimentally derived using a simple standardized procedure. Four industrially relevant materials were investigated for thermal model and software validation. In the framework of large format 3D printed tool manufacturing, 40 wt% carbon fiber reinforced polyamide 6 (PA6) and 20 wt% carbon fiber reinforced acrylonitrile-butadiene-styrene (ABS), polycarbonate (PC), and polyetherimide (PEI) play a strategic role in most applications. In addition, the research offers a physical, mechanical and thermal characterization of the printed workpiece providing a comprehensive guideline for part design, arrangement, and thermal compensation for traditional CFRP manufacturing tools. Finally, for each material, a real tool manufacturing case study and post-processed surface qualification is presented.

Yes / Real time measurement of melt rheology has been investigated as a Process Analytical Technology (PAT) to monitor hot melt extrusion of an Active Pharmaceutical Ingredient (API) in a polymer matrix. A developmental API was melt mixed with a commercial copolymer using a heated twin screw extruder at different API loadings and set temperatures. The extruder was equipped with an instrumented rheological slit die which incorporated three pressure transducers flush mounted to the die surface. Pressure drop measurements within the die at a range of extrusion throughputs were used to calculate rheological parameters such as shear viscosity and exit pressure, related to shear and elastic melt flow properties respectively. Results showed that the melt exhibited shear thinning behavior whereby viscosity decreased with increasing flow rate. Increase in drug loading and set extrusion temperature resulted in a reduction in melt viscosity. Shear viscosity and exit pressure measurements were found to be sensitive to API loading. These findings suggest that this technique could be used as a simple tool to measure material attributes in-line, to build better overall process understanding for hot melt extrusion.

Yes / Grinding solid reagents under solvent-free or low-solvent conditions (mechanochemistry) is emerging as a general synthetic technique which is an alternative to conventional solvent-intensive methods. However, it is essential to find ways to scale-up this type of synthesis if its promise of cleaner manufacturing is to be realised. Here, we demonstrate the use of twin screw and single screw extruders for the continuous synthesis of various metal complexes, including Ni(salen), Ni(NCS)2(PPh3)2 as well as the commercially important metal organic frameworks (MOFs) Cu3(BTC)2 (HKUST-1), Zn(2-methylimidazolate)2 (ZIF-8, MAF-4) and Al(fumarate)(OH). Notably, Al(fumarate)(OH) has not previously been synthesised mechanochemically. Quantitative conversions occur to give products at kg h−1 rates which, after activation, exhibit surface areas and pore volumes equivalent to those of materials produced by conventional solvent-based methods. Some reactions can be performed either under completely solvent-free conditions whereas others require the addition of small amounts of solvent (typically 3–4 mol equivalents). Continuous neat melt phase synthesis is also successfully demonstrated by both twin screw and single screw extrusion for ZIF-8. The latter technique provided ZIF-8 at 4 kg h−1. The space time yields (STYs) for these methods of up to 144 × 103 kg per m3 per day are orders of magnitude greater than STYs for other methods of making MOFs. Extrusion methods clearly enable scaling of mechanochemical and melt phase synthesis under solvent-free or low-solvent conditions, and may also be applied in synthesis more generally. / EPSRC (EP/L019655/1)

Yes / Chemical manufacturing typically requires more than one step, involving multiple batch processes, which makes synthesis at scale laborious and wasteful. Herein, we demonstrate that several reactions can be telescoped into a single continuous process and/or be carried out as a continuous multi-component reaction (MCR), by twin screw extrusion (TSE), in the complete absence of solvent. / EPSRC (EP/L019655/1).

No / Mechanochemical synthesis has been applied to the rapid synthesis of Deep Eutectic Solvents (DESs), including Reline 200 (choline chloride : urea, 1 : 2), in a continuous flow methodology by Twin Screw Extrusion (TSE). This gave products in higher purity and with Space Time Yields (STYs), four orders of magnitude greater than for batch methods

No / The oligomerisation of L-amino acids by papain was studied in a mixer ball mill and in a planetary ball mill. The biocatalyst proved stable under the ball milling conditions providing the corresponding oligopeptides in good to excellent yields and with a variable degree of polymerisation. Both parameters were found to be dependent on the reaction conditions and on the nature of the amino acid (specifically on its side-chain size and hydrophobicity). In addition, the chemoenzymatic oligomerisation was demonstrated by utilising twin-screw extrusion technology, which allowed for a scalable continuous process. Finally, the synthesised oligo(L-Leu) 2b proved to be active as a catalyst in the Juliá–Colonna enantioselective epoxidation of chalcone derivatives. / We acknowledge RWTH Aachen University for support by the Distinguished Professorship Program funded by the Excellence Initiative of the German federal and state governments. We kindly acknowledge Marcus Frings and Plamena Staleva for the HPLC analysis of products 4a–c (RWTH Aachen University) and ASEP for the TGA analysis (Queen’s University Belfast). D. E. C. and S. L. J. acknowledge the agency EPSRC, grant no. EP/R019655/1. Part of this work was performed at the Center for Chemical Polymer Technology (CPT) unit of DWI, which was supported by the EU and the federal state of North Rhine-Westphalia (grant EFRE 30 00 883 02).

Yes / The continuous and scalable synthesis of a porous organic cage (CC3), obtained through a 10-component imine polycondensation between triformylbenzene and a vicinal diamine, was achieved using twin screw extrusion (TSE). Compared to both batch and flow syntheses, the use of TSE enabled the large scale synthesis of CC3 using minimal solvent and in short reaction times, with liquid-assisted grinding (LAG) also promoting window-to-window crystal packing to form a 3-D diamondoid pore network in the solid state. A new kinetically trapped [3+5] product was also observed alongside the formation of the targeted [4+6] cage species. Post-synthetic purification by Soxhlet extraction of the as-extruded ‘technical grade’ mixture of CC3 and [3+5] species rendered the material porous. / Engineering and Physical Sciences Research Council (EPSRC) under the Grants EP/R005710/1 (AIC) and EP/R005540/1 (SLJ), and for an EPSRC Summer Vacation Bursary at the University of Liverpool (FG, RLG). We also thank the European Research Council under FP7, RobOT, ERC Grant Agreement No. 321156 (AIC), for financial support. RLG thanks the Royal Society for a University Research Fellowship.

This research investigates formulation, compounding and thin-wall injection moulding of Polypropylene/clay nanocomposites (PPCNs) prepared using conventional melt-state processes. An independent study on single screw extrusion dynamics using Design of Experiments (DoE) was performed first. Then the optimum formulation of PPCNs and compounding conditions were determined using this strategy. The outcomes from the DoE study were then applied to produce PPCN compounds for the subsequent study of thin-wall injection moulding, for which a novel four-cavity injection moulding system was designed using CAD software and a new moulding tool was constructed based upon this design. Subsequently, the effects of moulding conditions, nanoclay concentration and wall thickness on the injection moulded PPCN parts were investigated. Moreover, simulation of the injection moulding process was carried out to compare the predicted performance with that obtained in practice by measurement of real-time data using an in-cavity pressure sensor. For the selected materials, the optimum formulation is 4 wt% organoclay (DK4), 4 wt% compatibiliser (Polybond 3200, PPgMA) and 1.5 wt% co-intercalant (erucamide), as the maximum interlayer spacing of clay can be achieved in the selected experimental range. Furthermore, DoE investigations determined that a screw speed of 159 rpm and a feed rate of 5.4 kg/h are the optimum compounding conditions for the twin screw extruder used to obtain the highest tensile modulus and yield strength from the PPCN compounds. The optimised formulation of PPCNs and compounding conditions were adopted to manufacture PPCN materials for the study of thin-wall injection moulding. In the selected processing window, tensile modulus and yield strength increase significantly with decreasing injection speed, due to shear-induced orientation effects, exemplified by a significantly increased frozen layer thickness observed by optical microscopy (OM) and Moldflow® simulation. Furthermore, the TEM images indicate a strong orientation of clay particles in the flow direction, so the PPCN test pieces cut parallel to the flow direction have 36.4% higher tensile modulus and 13.6 % higher yield strength than those cut perpendicular to the flow direction, demonstrating the effects of shear induced orientation on the tensile properties of thin-wall injection moulded PPCN parts. In comparison to injection speed, mould temperature has very limited effects in the selected range investigated (25-55 °C), in this study. The changes in moulding conditions show no distinctive effects on PP crystallinity and intercalation behaviour of clay. Impact toughness of thin wall injection moulded PPCN parts is not significantly affected by either the changes in moulding conditions or clay concentration (1-5 %). The SEM images show no clear difference between the fracture surfaces of PPCN samples with different clay concentrations. TEM and XRD results suggest that higher intercalation but lower exfoliation is achieved in PPCN parts with higher clay content. The composites in the thin sections (at the end of flow) have 34 % higher tensile modulus and 11 % higher yield strength than in the thicker sections, although the thin sections show reduced d001 values. This is attributed to the significantly enhanced shear-induced particle/molecular orientation and more highly oriented frozen layer, according to TEM, OM and process simulation results. In terms of the reduced d001 values in the thin sections, it is proposed that the extreme shear conditions in the thin sections stretch the PP chains in the clay galleries to a much higher level, compaction of clay stacks occurs as less interspacing is needed to accommodate the stretched chains, but rapid cooling allows no time for the chains to relax and expand the galleries back. Overall, data obtained from both actual moulding and simulation indicate that injection speed is of utmost importance to the thin-wall injection moulding process, development of microstructure, and thus the resulting properties of the moulded PPCN parts, in the selected experimental ranges of this research.