Geckos can freely climb on walls and ceilings against their body weight at speed of over 1ms-1. Switching between attachment and detachment seem simple and easy for geckos, without considering the surface to be dry or wet, smooth or rough, dirty or clean. In addition, gecko can shed dirt particles during use, keeping the adhesive pads clean. Mimicking this biological system can lead to a new class of dry adhesives for various applications. However, gecko’s unique dry self-cleaning mechanism remains unknown, which impedes the development of self-cleaning dry adhesives. In this dissertation we provide new evidence and self-cleaning mechanism to explain how gecko shed particles and keep its sticky feet clean. First we studied the dynamic enhancement observed between micro-sized particles and substrate under dry and wet conditions. The adhesion force of soft (polystyrene) and hard (SiO2 and Al2O3) micro-particles on soft (polystyrene) and hard (fused silica and sapphire) substrates was measured using an atomic force microscope (AFM) with retraction (z-piezo) speed ranging over 4 orders of magnitude. The adhesion is strongly enhanced by the dynamic effect. When the retraction speeds varies from 0.02 µm/s to 156 µm/s, the adhesion force increases by 10% ~ 50% in dry nitrogen while it increases by 15%~70% in humid air. A dynamic model was developed to explain this dynamic effect, which agrees well with the experimental results. Similar dynamic enhancement was also observed in aqueous solution. The influence of dynamic factors related to the adhesion enhancement, such as particle inertia, viscoelastic deformations and crack propagation, was discussed to understand the dynamic enhancement mechanisms. Although particles show dynamic enhancement, Gecko fabrillar hair shows a totally different trend. The pull off forces of a single gecko seta and spatula was tested by AFM under different pull-off velocities. The result shows that both the spatula and the seta have a rate independent adhesion response in normal retraction, which is quite different from micro-particles. Further research indicated the shape of the contact area was a key factor to the dynamic effect. In order to verify this hypothesis, artificial gecko spatula made of glass fibers was nanofabricated by a focus ion beam (FIB) and tested by AFM. These manmade spatulae also show a rate independent adhesion response. The dynamic adhesion of a single gecko seta and spatula were simulated with finite element analysis and the results also confirm the rate independent phenomena.. In conclusion, self-cleaning is induced by dynamic effect during gecko locomotion. The relative dynamic adhesion change between particles and seta makes it possible for gecko to shed the dirt particles while walking.Finally, the fatigue property of gecko seta was examined with the atomic force microscope under cyclic attachment/detachment process, mimicking gecko running. The adhesion force versus cycles has been tested and evaluated. Fatigue mechanism of gecko seta was also analyzed based on the experimental findings.

Superhydrophobic (SH) surfaces are super water repellent surfaces on which a droplet of water will bead up like a marble and roll off the surface with minimal tilting of the surface. This is caused by the combination of a hydrophobic coating and a rough surface structure. To achieve thermodynamic stability, surface tension of the water pulls the droplet into this shape to minimize the contact area between the droplet and the surface. This creates a high contact angle (CA) between the droplet and the surface and a low sliding angle (SA) of which the droplet begins to roll off the surface. SH surfaces have a variety of potential applications such as drag reduction, anti-icing, improved heat transfer through condensation, and self-cleaning. Numerous reports have been dedicated to exploring the fluid dynamic behavior of water droplets on SH surfaces. This thesis focuses on exploring the self-cleaning properties of SH surfaces. Surfaces contaminated with salt, tobacco, and pollen are cleaned by rolling water droplets over the surface or condensing water on the surface such that when large enough, these droplets roll away due to gravity. SH surfaces explored here are composed of micro-scale or nano-scale rib and cavity structures and are compared with smooth, hydrophobic surfaces with a similar hydrophobic coating. To determine the self-cleaning efficiency of each surface, the CA and SA were measured before and after each surface was cleaned. In this study, it was observed that the presence of each of the three contaminates considered greatly affects the overall hydrophobicity of the surface, as indicated by the CA and SA. Ideally, as the contaminates are removed from the surface, the hydrophobicity of the surface improves to match the hydrophobicity of a clean surface. This is best seen on surfaces contaminated with salt as the CA and SA match that of a clean surface after only two to three water droplets roll over the surface or after the first condensed water droplets roll off the surface. This implies that all the salt particles are removed from the SH surface. Surfaces contaminated with tobacco showed that the hydrophobicity improves to a limited extent when cleaned with rolling water droplets or condensation but never is capable of matching the hydrophobicity of a clean surface. This suggests that only a portion of the tobacco residue is capable of being removed from the surface by either of the two cleaning methods considered in this thesis. Finally, when water came in contact with pollen on the surfaces, it experienced hydrodynamic osmosis leading to cellular bursting. After cellular bursting, the surface behaves as a hydrophilic surface and selfcleaning properties were never observed on any surface contaminated with pollen. Thus, overall this study shows that rolling water droplets over a contaminated surface and condensing water droplets on a contaminated surface are both viable means of utilizing the self-cleaning properties on SH surfaces. For the contaminates considered in this study, the efficiency of the self-cleaning surfaces is shown to be the same for both micro-structured and nano-structured surfaces.

The remarkable attachment system of geckos has inspired the development of dry microfiber adhesives through the last two decades. Some of the notable characteristics of gecko-inspired fibrillar adhesives include: strong, directional, and controllable adhesion to smooth and rough surfaces in air, vacuum, and under water; ability to maintain strong adhesion during repeated use; anti-fouling and self-cleaning after contamination. Given these outstanding qualities, fibrillar adhesives promise an extensive range of use in industrial, robotic, manufacturing, medical, and consumer products. Significant advancements have been made in the design of geckoinspired microfiber adhesives with the characteristic properties listed above, with the exception of the anti-fouling and self-cleaning features. The self-cleaning mechanism of the gecko’s adhesion system plays an important role to its ability to remain sticky in various environments. Similarly, enabling self-cleaning capability for synthetic microfiber adhesives will lead to robust performance in various areas of application. Presently, the practical use of fibrillar adhesives is restricted mainly to clean environments, where they are free from contaminants. The goal of this thesis is to conduct a detailed study of the mechanisms and mechanics of contact-based self-cleaning of gecko-inspired microfiber adhesives. This work focuses on contact self-cleaning mechanisms, as a more practical approach to cleaning. Previous studies on the cleaning of microfiber adhesives have mostly focused on mechanisms that involve complete removal of the contaminants from the adhesive. In this thesis, a second cleaning process is proposed whereby particles are removed from the tip of the microfibers and embedded between adjacent microfibers or in grooves patterned onto the adhesive, where they are no longer detrimental to the performance of the adhesive. In this work, a model of adhesion for microfiber adhesives that take the deformation of the backing layer under individual microfiber is developed. The dependence of adhesion of microfiber adhesives on the rate of unloading is also modeled and verified using experiments. The models of adhesion presented are later used to study the mechanics of contact self-cleaning of microfiber adhesives. Three major categories of self-cleaning are identified as wet self-cleaning, dynamic self-cleaning, and contact self-cleaning. A total of seven self-cleaning mechanisms that are associated with these categories are also presented and discussed. Results from the self-cleaning model and experiments show that shear loading plays an important role in self-cleaning. The underlying mechanism of contact self-cleaning due to normal and shear loading for spherical contaminants is found to be the particle rolling between the adhesive and a contacted substrate. Results from the model and experiments also show that small microfiber tips (much less than the size of the contaminants) are favorable for self-cleaning. On the other hand, large microfiber tips (much larger than the size of the contaminants) are favorable for anti-fouling of the microfiber adhesive. Results from this work suggests that the sub-micrometer size of the gecko’s adhesive fibers and the lamellae under the gecko toes contribute to its outstanding self-cleaning performance. The results presented in this thesis can be implemented in the design of microfiber adhesives with robust adhesion, self-cleaning and anti-fouling characteristic, for use in numerous applications and in various environments.

Geckos are famous for the skill of switchable adhesion that they use to stick on various surface while keep their fingers super clean. In the dissertation, a unique mechanism was discovered to explain gecko self-cleaning phenomena. Using atomic force microscopy (AFM), we managed to compare the microparticle-substrate adhesion and the microparticle-seta adhesion with a single seta bonded to the AFM cantilever. A dynamic effect was approved that high pulling-off speed could increase the microparticle-substrate adhesion and thus the self-cleaning appears at high moving speed. Based on the self-cleaning theory, a gecko-inspired N-doped graphene surface with switchable adhesion was achieved, which was designed into a bio-inspired micromanipulator with a success rate over 90%. When electrical bias was applied on this biomimetic surface, the charge concentration induced an electrical double layer (ELD) on the convex surfaces, which attracts polar water molecules to form a water bridge on it, significantly enhancing the adhesion on the wrinkled graphene surface, mimicking the capillary force on beetle feet. Therefore, the bio-inspired adhesive surface can be controlled with speed, electrical bias, humidity and different material surfaces. The water attraction phenomenon on the polarized surface was further tested for the potential application of water collection and evaporation in microsystems.

No description available.

This research comprehensively reviews the properties of regular micro and nano structures fabricated by laser interference lithography and reports on their applications in the antireflection and self‐cleaning surface. The research systematically investigates the laser interference lithography technology taking into account its advantages and abilities to realize various potential applications. Multiple‐beam interference lithography systems are constructed. Laser interference interaction with silicon wafer is analysed and the optical and hydrophobic properties are obtained via measurements. In order to fabricate the extremely low reflection and very large contact angle for solar cells, fabrication methods of antireflection and self‐cleaning are surveyed and their advantages and disadvantages compared. The research investigates the effect of heat transfer and the radiation of laser interference plasma on silicon wafer surfaces and proposes equations of heat flow and radiation effects of laser plasma of interfering patterns in a four‐beam laser interference distribution. Following the irradiation, the silicon wafer surface is covered with a periodic array of micrometer and nanometer‐sized structures, which have the shape of grating, cone and hole. The research also investigates the effect of different laser parameters on the optical and hydrophobic properties of the structured silicon wafer surface. The results of periodic hexagonally‐distributed hole structures fabricated by three‐beam laser interference reveals excellent design guidelines for obtaining an extremely low solar‐weighted reflection, (SWR, 1.86%) and relatively large contact angle (140°) which can provide a strong self‐cleaning capability on the solar cell surface. In addition, the research creates a novel dual structure with antireflection and superhydrophobic properties fabricated by three‐beam laser interference lithography. The fabrication method is three‐beam laser interference combined with focused laser processing interacting on the silicon wafer surface. This kind of structure has a very low SWR (3.6 %) and extremely large contact angle which is more than 150° in the wavelength range from 380 nm to 780 nm. The research shows that the laser interference lithography technology can be employed and further developed to fabricate micro and nano structures of strong antireflection and self‐cleaning functions for applications in solar cells.

Ao longo do tempo, os revestimentos de fachada permanecem expostos a diversos agentes de degradação, sejam eles associados aos próprios materiais empregados ou a fatores externos. Tal exposição implica em manchas formadas a partir da deposição de partículas poluentes na superfície dos revestimentos, elevando seus custos para limpeza e manutenção. Uma vez que permanecem expostas à radiação solar, as fachadas se mostram atraentes ao uso de materiais fotocatalíticos, os quais catalizam a mineralização de agentes poluentes, transformando-os em produtos inócuos. A adição de dióxido de titânio (TiO2) a argamassas e concretos de cimento branco desenvolve superfícies autolimpantes, reduzindo a formação de manchas e mantendo sua coloração original ao longo do tempo. No entanto, a eficiência e a economia no uso de materiais fotocatalíticos em aplicações reais é fortemente afetada pela disponibilidade da radiação ultravioleta adequada para ativá-los. Portanto, o presente trabalho busca avaliar a capacidade autolimpante de argamassas e coberturas fotocatalíticas de TiO2 expostas a diferentes configurações de posicionamento no microclima urbano da cidade de Porto Alegre. Para isto, foram confeccionadas amostras de argamassa e coberturas de pasta ou argamassa contendo diferentes teores de TiO2, as quais foram manchadas com Rodamina B e lodo de cinzas da queima de eucalipto e, a seguir, expostas sob diferentes condições de posicionamento, voltadas para as orientações norte, sul, leste e oeste, à 0º, 45º e 90º. Ao longo do período de exposição, foram realizadas leituras cromáticas (sistema CIELab) na superfície das amostras, tendo em vista a descoloração dos manchamentos aplicados. Para aquelas manchadas com Rodamina B, a degradação do corante se mostrou mais eficiente nas argamassas com maiores teores de TiO2 e nas configurações de posicionamento que recebem maior incidência de radiação solar. As coberturas de pasta apresentaram valores mais elevados de variação de cor (ΔE) e refletância (L*), na comparação à aplicação do TiO2 como cobertura de argamassa ou incorporado à mistura − métodos os quais se mostraram resultados equivalentes. / Building façades are commonly exposed to polluting agents generated by vehicles and industries exhausts, which cause stains on their surfaces and increase efforts and costs both for cleaning and maintenance. Facades are attractive to photocatalytic materials usage, which transform pollutants to innocuous products. The addition of titanium dioxide (TiO2) to white cement mortars and concretes develops self-cleaning surfaces which are capable to reduce stains and maintain their original color along the time. However, efficiency and economy in the use of photocatalytic materials in real applications are strongly affected by the availability of suitable ultraviolet radiation to activate them. This thesis aims to evaluate the self-cleaning ability of TiO2-containing mortars and coatings (paste or mortar) exposed to controlled positioning settings in the urban environment of Porto Alegre, Brazil. Mortars and coatings were prepared containing different additions of TiO2 and then were soiled by Rhodamine B (RhB) or burning ashes of eucalyptus sludge. Samples were exposed under outdoor conditions facing north, south, east and west orientations, 0º, 45º or 90º slopes. During the exposure test, discoloration effect on samples' surface was monitored by colorimetric measurements (CIELab color space) using a portable spectrophotometer. A final analysis was performed at the end of the measurements, including statistical tests. Self-cleaning ability was better seen both for higher additions of TiO2 and settings which receive higher intensities of solar radiation. Cement paste coatings showed higher values both of color change and reflectance when compared to mortar coatings or TiO2 added to the mixture − which performed equivalent results.

The present study is an integral part of a broader study focused on the design and implementation of self-cleaning culverts, i.e., configurations that prevent the formation of sediment deposits after culvert construction or cleaning. Sediment deposition at culverts is influenced by many factors, including the size and characteristics of material of which the channel is composed, the hydraulic characteristics generated under different hydrologic events, the culvert geometry design, channel transition design, and the vegetation around the channel. The multitude of combinations produced by this set of variables makes the investigation of practical situations challenging. In addition to the above considerations, the field observations, and the laboratory and numerical experiments have revealed additional complexities of the flow and sediment transport through culverts that further increase the dimensions of the investigation. The flow complexities investigated in this study entail: flow non-uniformity in the areas of transition to and from the culvert, flow unsteadiness due to the flood wave propagation, and the complex correlation between the flow and sediment hydrographs produced during storm events. To date, the literature contains no systematic studies on sediment transport through multi-box culverts. Similarly, there is limited knowledge about the non-uniform, unsteady sediment transport in channels of variable geometry. Furthermore, there are few readily useable numerical models that can reliably simulate flow and sediment transport in such complex situations. Given the current state of knowledge, the main goal of the present study is to investigate the above flow complexities in order to provide the needed insights for optimizing the culvert design. The research was phased so that field observations were conducted first to understand the culvert behavior in Iowa landscape. Modeling through complementary hydraulic model and numerical experiments was subsequently carried out to gain the practical knowledge for the development of the self-cleaning culvert designs.

<p>Då marina enheter numera deltar i internationella missioner, kommer den nya miljön som enheterna opererar i att påverka bland annat deras sensorer.</p><p>Den här studien avhandlar några av de nu framtagna självsanerande ytbeläggningarna och ger en presentation av hur de fungerar på några marina elektrooptiska sensorers yttersta linser.</p><p>Studien försöker ge svar på ytbeläggningarnas transmittans och hur effektivt de kan sanera bort oönskade saltlager tillsammans med andra nedsmutsande partiklar från sensorlinserna samt den militära nyttan av att använda självsanerande ytbeläggning.</p> / <p>This study deals with now developed self-cleaning coatings and gives a presentation of how they work on some electro-optical sensor lenses used in the navy. The study also examines the coatings transmittance and how efficient they can clean the sensor lenses from undesired salt layers and other soiling particles.</p><p>After the introduction the study presents basic facts of the chosen sensors, nanotechnology, surface wettability and also salts and salinity. Thereafter the study describes current nano-research on self-cleaning coatings and possible results there of, when the coatings are applied on the different sensors.</p><p>In the study I give my opinion of the military benefit of using self-cleaning coatings, which from a general point of view is that there mostly are positive effects using such a coating, in a technical perspective.</p><p>The study ends with conclusions that there are self-cleaning coatings based on TiO₂-nanoparticles which can transmit within the visual spectra and also can clean undesired soiling particles. But can not confirm that these coatings have the desired effect on salt crystals, or transmit within wavelengths spectrum for IR-detectors and lasers.</p> / ChpT 08-10

In this study photocatalytic antibacterial and self-cleaning activities of TiO2-SiO2 thin films as a function of TiO2/SiO2 ratios were investigated. TiO2-SiO2 mixed oxides were synthesized by sol-gel method and coated over soda-lime glass plates by dip coating technique. Escherichia coli was used as a model microorganism for the photocatalytic antibacterial tests. Degradation rate of methylene blue (MB) molecules was used to characterize photocatalytic self-cleaning activities of thin film surfaces. The maximum antibacterial activity was achieved over 92 wt% SiO2 containing thin films. However, when the SiO2 content exceeds 92 wt%, photocatalytic antibacterial activity decreased considerably, which was explained by the dilution of TiO2 phase and inaccessibility of TiO2. Increase in photocatalytic antibacterial activity was attributed to increases in the relative surface area, roughness, hydroxyl (OH-) groups and bacterial adhesion. The favored bacterial adhesion enhanced direct contact of bacteria with TiO2 particles and surface reactive oxygen species. The highest initial decomposition rate of MB was obtained for 60 wt% SiO2 and the activity decreases as SiO2 concentration increases. The increase in photocatalytic activity by the SiO2 addition can be explained by the increase of the amount of MB per unit area of TiO2-SiO2 thin films. Different adsorption capability of thin films against MB molecule and E. coli cell was explained as the first reason why the antibacterial and self-cleaning activities reached their maximum values at different SiO2 ratios. The second reason could be related with the different control mechanisms of self-cleaning and antibacterial activities by different textural and surface properties.