Thesis (M.S.)--University of North Texas, Dec., 2008. / Title from title page display. Includes bibliographical references.

Squat reinforced concrete shear walls are stiff structural elements incorporated in buildings and other structures and are capable of resisting large seismic demands. However, when not properly designed, they are prone to shear-related brittle failure. To improve the seismic behaviour of these structural elements, a retrofitting bracing system incorporating superelastic Shape Memory Alloys (SMAs) was developed. Superelastic Shape Memory Alloys (SMAs) are smart materials with the ability to sustain and recover large pseudo-plastic deformations while dissipating energy. The SMA bracing system consists of tension-only SMA links coupled with rigid steel elements. The SMA links were designed to sustain and recover the elongation experienced by the bracing system, while the steel elements were designed to sustain negligible elastic elongations. The SMA bracing system was installed on third-scale, 2000 mm × 2000 mm, shear walls, which were tested to failure under incremental reverse cyclic loading. The experimental results demonstrated that the tension-only SMA braces improve the seismic response of squat reinforced concrete walls. The retrofitted walls experienced higher strength, greater energy dissipation, and less permanent deformation. The re-centering properties of the SMA contributed to the reduction of pinching in the hysteretic response due mainly to the clamping action of the SMA bracings while recovering their original length. The walls were numerically simulated with the nonlinear finite element program VecTor2. The numerical simulations accurately captured the hysteretic response of both the original and the retrofitted walls. A parametric study was conducted to assess the effect of axial loading and size of the SMA braces.

This paper investigates the linear elastic behavior of timber shear walls under monotonic prescribed displacement. ABAQUS© 16.4-5, is a numerical finite element software used as the primary analysis methodology.  Parameterized models are created for two shear wall specimens of different geometry concerning door and window configurations. The shear walls are simulated as solid timber framing which is mechanically connected to gypsum sheathing board through fasteners. The primary findings are the linear elastic shear force distribution of the mechanical joints. Additionally, deformations and reaction forces of the shear walls are determined. The overall horizontal shear wall behavior of each specific wall was also studied in the presence of door and window openings. The simulations indicate there is a clear deformation difference in the behaviors of the two shear walls. Furthermore, the highest shear force values of the fasteners are located around the corners of the openings. The findings are supported by other researcher’s experiments and analytical tests, timber shear wall theory and Eurocode design requirements.

No description available.

No abstract is provided. / Thesis / Master of Engineering (MEngr) / Scope and contents: The aim of this thesis is to present a finite difference method, for analysing coupled shear walls with constant or variable cross-section, resting on rigid or elastic foundations and with elastic or inelastic connecting beams. It is also intended to compare the finite difference method with the continuous connection method, which can be developed using Rosman's approach or Newmark's concept for analysing composite beams or the energy approach, and with the finite element method. An analysis of coupled shear walls with multiple piers is presented.

This dissertation is relevant to structural engineers focusing on seismic design of structures using reinforced masonry. Specifically the thesis focuses on the seismic performance of reinforced masonry shear walls as seismic force resisting systems. / Reinforced masonry (RM) has been gaining a wide acceptance in the low- and mid-rise construction market as an economic and durable structural system. However, challenges still exist in the area of seismic design because of the poor performance of unreinforced masonry during recent earthquake events in Iran 2003, Haiti 2010, Japan 2011, New Zealand 2011 and Nepal 2015. The dissertation investigated the seismic performance of six concrete block structural walls in an effort to evaluate their force-, displacement- and performance- based seismic design parameters. The walls fall under the ductile shear wall/special reinforced wall seismic force resisting system (SFRS) classification according to the current North American masonry design standards. More specifically, the dissertation is focused on evaluating if such walls, designed under the same prescriptive design provisions, having different cross-section configurations would possess similar seismic performance parameters. This was established through an experimental and analytical program by subjecting the walls to a displacement controlled quasi-static cyclic analysis. Different wall configurations were tested including, rectangular, flanged and slab-coupled walls. Test results confirmed that walls designed under the same SFRS classification, but with different configurations, have different seismic performance parameters that included ductility capacity; yield and post yield displacement; stiffness degradation; period elongation and equivalent viscous damping. The current North American masonry design provisions do not account for such difference in the ductility capacities between the walls. The thesis analyses were concluded by quantifying the seismic vulnerability of a RM SFRS comprised of shear walls similar to those tested, through the development of collapse fragility curves and the assignment of an adjusted collapse margin ratio, ACMR following the FEMA P-58 and P-695 guidelines. The system were deemed acceptable since the ACMR was greater than ACMR10% (2.35 > 2.31). Therefore, the selected RM SFRS which was designed to meet the prescriptive requirements of the ductile masonry walls classification of the CSA S304 (CSA 2014), shows potential capacity against collapse under high intensity earthquakes in one of the highest seismic zones in western Canada and it should be considered as a viable SFRS to be used in seismic design. The procedure described in the chapter can be adopted to investigate the collapse fragility of other SFRS in different seismic regions through careful selection and scaling of the ground motion records associated with such region's seismicity. / Dissertation / Doctor of Philosophy (PhD)

<p>The masonry construction industry represents a historically significant and substantial portion of both existing and new residential, commercial and institutional low- to medium-rise structures across Canada. Although commonly chosen for its aesthetic qualities by architects, structural masonry walls constructed with concrete block units are also an effective lateral force (wind or seismic) resisting system. The purpose of this dissertation is to address what are perceived to be overly conservative and outdated practices within masonry construction and design by adopting analysis and design practices which have had success with similar reinforced concrete wall systems. The results from a test program reporting on the behavior of nine fully-grouted reinforced masonry (RM) structural walls containing confined boundary elements are analyzed and presented according to force-, displacement- and performance-based seismic design considerations. The boundary element containing four vertical bars with lateral confinement stirrups selected represents a readily codified and practically achievable means of achieving seismic performance enhancement. The design and detailing of the specimens represented a range of parameters that would be anticipated to vary within low- to medium-rise RM buildings. In addition, an analytical study is carried out to derive, from first principles of stress equilibrium and strain compatibility, the necessary constitutive material and mechanics-based equations needed to solve for the state of shear stress and strain in an idealized cracked masonry macro-element. The algorithm proposed is validated by comparing the proposed model to existing test data and is further developed towards predicting the design shear strength of RM structural walls. The results from these experimental and analytical research programs are subsequently used to provide a set of proposed code clauses at the end of the thesis. Prescriptive design requirements are proposed for a new category of <em>Special Ductile Masonry Shear Wall</em> containing boundary elements including integration of a new shear strength expression. These clauses have been written with the intention of adoption within the CSA S304.1 and the MSJC North American masonry designs standards.</p> / Doctor of Philosophy (PhD)

Investigation of simply supported Multilayer sandwich beams with symmetrical loading and of Multipier shear walls with arbitrary horizontal loadings. The analysis contains the influence of normal deformation of the layers and piersrespectively. / Thesis / Master of Engineering (ME)

Increasing interest, from the U.S. Army Corps of Engineers (USACE) and other agencies, in using deep-mixing methods (DMM) to improve the stability of levees constructed on soft ground is driven by the need to reduce levee footprints and environmental impacts and to allow for more rapid construction. Suitable methods for analysis and design of these systems are needed to ensure that the DMM technology is properly applied. DMM shear walls oriented perpendicular to the levee alignment are an effective arrangement for supporting unbalanced lateral loads. Shear walls constructed by overlapping individual DMM columns installed with single-axis or multiple axis equipment include vertical joints caused by the reduced width of the wall at the overlap between adjacent columns. These joints can be made weaker by misalignment during construction, which reduces the efficiency of the overlap. Depending on the prevalence and strength of these joints, complex failure mechanisms, such as racking due to slipping along vertical joints between adjacent installations in the shear walls, can occur. Ordinary limit equilibrium analyses only account for a composite shearing failure mode; whereas, numerical stress-strain analyses can account for other failure modes. Five case studies provided by the USACE were analyzed to evaluate the behavior of levee and floodwall systems founded on soft ground stabilized with DMM shear walls. These identified and illustrated potential failure mechanisms of these types of systems. Two-dimensional numerical stability and settlement analyses were performed for the case studies using the FLAC computer program. The key findings and conclusions for the individual case studies were assessed and integrated into general conclusions about design of deep-mixing support for levees and floodwalls. One of the significant findings from this research was to identify the potential for a partial depth racking failure, which can control design when the DMM shear walls are socketted into a relatively strong bearing layer. The potential for partial depth racking failure is not discussed in the literature and represents a new failure mode identified by this research. This discovery also highlights the importance of adapting suitable methods for analysis and design of these systems to address all potential failure modes. / Ph. D.

Steel plate shear walls (SPSWs) are popular lateral force resisting systems whose practical applications range from high seismic regions to medium and low seismic areas and wind load applications. The factors which make SPSW attractive include its energy dissipation capacity, excellent ductility, constructability, speed of construction compared to concrete shear walls, reduced architectural footprint compared to concrete shear walls, and increased inelastic deformation capacity as compared to braced frames. The principle behind current SPSW design is that the post-buckling tension field capacity of the thin web plate is proportioned to resist the full lateral load. The resulting web plate is typically quite thin, buckles at low loads, possesses low stiffness, and does not provide resistance when the lateral loads are reversed until the tension field engages in the opposite direction. To compensate for these shortcomings, moment connections are required at the beam to column connections to improve energy dissipation, increase stiffness, and provide lateral resistance during load reversal. The resulting SPSW designs with very thin web plates, moment connections, and beams and columns significantly larger than comparable braced frames, can result in inefficient structural systems. The objective of this work is to develop steel plate shear wall systems that are more economic and efficient. In order to achieve this, approaches like shear connections between beams and columns, allowing some yielding in columns and increasing plate thicknesses were attempted. But these approaches were not effective in that there was no reduction in the amount of steel required since stiffness controlled the designs. This necessitated the creation of tunable steel plate shear wall systems in which strength and stiffness could be decoupled. Preliminary analyses of seven steel plate shear wall systems which allow tunability were conducted and two configurations namely circular holes and butterfly shaped links around the perimeter, that showed promising results were chosen. The solid plate in the middle of the panel contributes significant pre-yield stiffness to the system while the geometry of the perimeter perforations controls strength and ductility. An example panel was designed using the two approaches and compared to panels designed using current SPSW design methods. The proposed configurations resulted in improved overall performance of the system in terms of energy dissipation, stable hysteresis, required less steel and no moment connections between beams and columns. This was also observed from the parametric study that was performed by varying the thickness of the web plate and the geometry of the configurations. Thus it was concluded that the two proposed configurations of cutouts were promising concepts that allow separate tuning of the system strength, stiffness and ductility and could be adopted in any seismic zone for improved seismic resistance. / Master of Science