The goal of this study is to design and evaluate economic and rapid seismic retrofit strategies for relatively small rehabilitation projects for steel structures consistent with the tenets of sustainable design. The need to retrofit existing structures in earthquake prone regions may arise directly from the problem of aging and deteriorating conditions, recognition of the vulnerability of existing infrastructure, from updates in seismic code requirements, or changes in building performance objectives. Traditional approaches to seismic hazard mitigation have focused reducing the failure probabilities, consequences from failures, and time to recovery. Such paradigms had been established with little regard to the impact of their rehabilitation measures on the environment and disruptions to occupants. The rapid rehabilitation strategies proposed here have sustainability benefits in terms of providing a more resilient building stock for our communities as well as minimizing environmental and economical impacts and social consequences during the rehabilitation project. To achieve these goals, a unique approach to design supplemental systems using tension-only elements is proposed. In this design approach undesirable global and local buckling are eliminated. Two rapid rehabilitation strategies are presented. The first is a bracing system consisting of cables and a central energy dissipating device (CORE Damper). The second is a shear wall system with the combined use of thin steel plate and tension-only bracing. Analytical studies using both advanced and simplified models and proof-of-concept testing were carried out for the two devices. The results demonstrated stable, highly efficient performance of the devices under seismic load. Preliminary applications of the CORE damper to the retrofitting of a braced steel frame showed the ability of the system to minimize soft story failures. Both techniques can be implemented within a sustainability framework, as these interventions reduce the seismic vulnerability of infrastructure, are low cost, utilize materials and fabrication processes widely available throughout the world, can be handled by unskilled labor and carried out with minimal disruptions to the environment. The approach taken in this study can provide a road map for future development of sustainability-based rehabilitation strategies.

<p>Wind loads acting on wooden building structures need to be dealt with adequately in order to ensure that neither the serviceability limit state nor the ultimate limit state is exceeded. For the structural designer of tall buildings, avoiding the possibly serious consequences of heavy wind loading while taking account at the same time of the effects of gravitation can be a real challenge. Wind loads are usually no major problem for low buildings, such as one- to two-storey timber structures involving ordinary walls made by nailing or screwing sheets of various types to the frame, but when taller structures are designed and built, serious problems may arise.</p><p>Since wind speed and thus wind pressure increases with height above the ground and the shear forces transmitted by the walls increase accordingly, storey by storey, considerable efforts can be needed to handle the strong horizontal shear forces that are exerted on the bottom floor in particular. The strong uplift forces that can develop on the wind side of a structure are yet another matter that can be critical. Accordingly, a structure needs to be anchored to the substrate or to the ground by connections that are properly designed. Since the calculated uplift forces depend very much upon the models employed, the choice of models and simplifications in the analysis that are undertaken also need to be considered carefully.</p><p>The present licentiate thesis addresses questions of how wind loads acting on multi-storey timber buildings can be best dealt with and calculated for in the structural design of such buildings. The conventional use of sheathing either nailed or screwed to a timber framework is considered, together with other methods of stabilizing timber structures. Alternative ways of using solid timber elements for stabilization are also of special interest.</p><p>The finite element method was employed in simulating the structural behaviour of stabilizing units. A study was carried out of walls in which sheathing was nailed onto a timber frame. Different structural levels were involved, extending from modelling the performance of a single fastener and of the connection of the sheathing to frame, to the use of models of this sort for studying the overall structural behaviour of wall elements that possess a stabilizing function. The results of models used for simulating different load cases for walls agreed reasonably well with experimental test results. The structural properties of the fasteners binding the sheathing to the frame, as well as of the connections between the members of the frame were shown to have a strong effect on the simulated behaviour of shear wall units.</p><p>Regarding solid wall panels, it was concluded that walls with a high level of both stiffness and strength can be produced by use of such panels, and also that the connections between the solid wall panels can be designed in such a way that the shear forces involved are effectively transmitted from one panel to the next.</p>

With the rise in constructing using FRP reinforcement, owing to corrosion problems in steel-reinforced structures, there is a need for a system to resist lateral loads induced from wind and earthquake loads. The present study addressed the applicability of reinforced-concrete shear walls totally reinforced with glass-fiber-reinforced polymer (GFRP) bars to attain reasonable strength and drift requirements as specified in different codes. Four large-scale shear walls - one reinforced with steel bars (as reference specimen) and three totally reinforced with GFRP bars - were constructed and tested to failure under quasi-static reversed cyclic lateral loading. The GFRP-reinforced walls had different aspect ratios covering the range of medium-rise walls. The reported test results clearly showed that properly designed and detailed GFRPreinforced walls could reach their flexural capacities with no strength degradation, and that shear, sliding shear, and anchorage failures were not major problems and could be effectively controlled. The results also showed recoverable and self-centering behavior up to allowable drift limits before moderate damage occurred and achieved a maximum drift meeting the limitation of most building codes. Acceptable levels of energy dissipation accompanied by relatively small residual forces, compared to the steel-reinforced shear wall, were observed. Finite element simulation was conducted and the analyses captured the main features of behavior. Interaction of flexural and shear deformations of the tested shear walls was investigated. It was found that relying on the diagonal transducers tended to overestimate shear distortions by 30% to 50%. Correcting the results based on the use of vertical transducers was assessed and found to produce consistent results. Decoupling the flexural and shear deformations was discussed. Using GFRP bars as elastic material gave uniform distribution of shear strains along the shear region, resulting in shear deformation ranging from 15 to 20% of total deformation. The yielding of the steel bars intensified the shear strains at the yielding location, causing significant degradation in shear deformation ranging from 2 to 40% of total deformation. The results obtained demonstrated significantly high utilization levels of such shear wall type, therefore, primary guidelines for seismic design of GFRP-reinforced shear wall in moderate earthquakes regions was presented, as no design guidelines for lateral load resistance for GFRP-reinforced walls are available in codes. The ultimate limit state was addressed by providing strength capacity that limit ductility demand to their safe flexural displacement capacity. The strength demands were derived from ground motion spectra using modification factors that depend on both the strength and energy absorption of the structure. Deformation capacity was derived by proposing new definitions for elastic (virtual yield) displacement and maximum allowable displacement. Strength modification factor was proposed based on the test results. The occurrence of "virtual plastic hinge" for GFRP-reinforced shear walls was described providing new definitions convenient with the behavior of the GFRP-reinforced shear walls. "Virtual plastic hinge" length was estimated based on observations and calculations. Subsequently, the experimental results were used to justify the proposed design procedure. The promising results could provide impetus for constructing shear walls reinforced with GFRP bars and constitute a step toward using GFRP reinforcement in such lateral-resisting systems.

In this study two dimensional steel frames, reinforced with un-stiffened thin steel panels, are investigated. In the first part of the study, the strip model, a method for analyzing un-stiffened thin steel plate shear walls, was investigated. Sensitivity studies to investigate the influence of the number of strip members to be used to in the strip model and their angle of inclination were conducted. In the second part, responses of various un-stiffened steel plate shear wall systems to lateral loads were investigated. The influences of three major parameters were studied. These are the beam-to-column connection type, the boundary frame stiffness and the plate slenderness ratio (the ratio of the centerline column spacing to the thickness of the plate). In both parts nonlinear pushover analysis were performed with SAP2000 structural analysis program. In this study, the history of development, theory and advantages of un-stiffened thin steel plate shear walls and recommendations for this lateral load resisting system are presented.

iv ABSTRACT SEISMIC DESIGN OF COLD FORMED STEEL STRUCTURES IN RESIDENTIAL APPLICATIONS Uygar, Celaletdin M.Sc., Department of Civil Engineering Supervisor: Prof. Dr. &Ccedil / etin Yilmaz May 2005, 82 pages In this study, lateral load bearing capacities of cold formed steel framed wall panels are investigated. For this purpose lateral load bearing alternatives are analyzed numerically by computer models and results are compared with already done experimental studies and approved codes. In residential cold formed steel construction, walls are generally covered with cladding material like oriented strand board (OSB) or plywood on the exterior wall surface and these sheathed light gauge steel walls behave as shear walls with significant capacity. Oriented strand board is used in analytical models since OSB claddings are most commonly used in residential applications. The strength of shear walls depends on different parameters like screw spacing, strength of sheathing, size of fasteners used and aspect ratio. SAP2000 software is used for structural analysis of walls and joint force outputs are collected by Microsoft Excel. The yield strength of shear walls at which first screw connection reaches its shear capacity is calculated and load carrying capacity per meter length is found. The nonlinear analysis is also done by modeling the screw connections between OSB and frame as non-linear link and the nominal shear capacities of walls are calculated for different screw spacing combinations. The results are consistent with the values in shear wall design Guide and International Building Code 2003. The other lateral load bearing method is flat strap X-bracing on wall surfaces. Various parameters like wall frame section thickness, flat strap area, aspect ratio and bracing number are investigated and results are evaluated. The shear walls in which X-bracing and OSB sheathing used together are also analyzed and the results are compared with separate analyses.

Wind loads acting on wooden building structures need to be dealt with adequately in order to ensure that neither the serviceability limit state nor the ultimate limit state is exceeded. For the structural designer of tall buildings, avoiding the possibly serious consequences of heavy wind loading while taking account at the same time of the effects of gravitation can be a real challenge. Wind loads are usually no major problem for low buildings, such as one- to two-storey timber structures involving ordinary walls made by nailing or screwing sheets of various types to the frame, but when taller structures are designed and built, serious problems may arise. Since wind speed and thus wind pressure increases with height above the ground and the shear forces transmitted by the walls increase accordingly, storey by storey, considerable efforts can be needed to handle the strong horizontal shear forces that are exerted on the bottom floor in particular. The strong uplift forces that can develop on the wind side of a structure are yet another matter that can be critical. Accordingly, a structure needs to be anchored to the substrate or to the ground by connections that are properly designed. Since the calculated uplift forces depend very much upon the models employed, the choice of models and simplifications in the analysis that are undertaken also need to be considered carefully. The present licentiate thesis addresses questions of how wind loads acting on multi-storey timber buildings can be best dealt with and calculated for in the structural design of such buildings. The conventional use of sheathing either nailed or screwed to a timber framework is considered, together with other methods of stabilizing timber structures. Alternative ways of using solid timber elements for stabilization are also of special interest. The finite element method was employed in simulating the structural behaviour of stabilizing units. A study was carried out of walls in which sheathing was nailed onto a timber frame. Different structural levels were involved, extending from modelling the performance of a single fastener and of the connection of the sheathing to frame, to the use of models of this sort for studying the overall structural behaviour of wall elements that possess a stabilizing function. The results of models used for simulating different load cases for walls agreed reasonably well with experimental test results. The structural properties of the fasteners binding the sheathing to the frame, as well as of the connections between the members of the frame were shown to have a strong effect on the simulated behaviour of shear wall units. Regarding solid wall panels, it was concluded that walls with a high level of both stiffness and strength can be produced by use of such panels, and also that the connections between the solid wall panels can be designed in such a way that the shear forces involved are effectively transmitted from one panel to the next.

Superelastic Shape Memory Alloys (SMAs) are being explored as alternative reinforcing materials to traditional deformed steel reinforcement for seismic applications. The main advantage is the ability of the SMA to recover large nonlinear strains, which promotes the self-centering phenomenon. The primary objective of this research is to present the performance, before and after repair, of slender reinforced concrete shear walls, one reinforced internally with SMAs in the boundary zones within the plastic hinge region and other control wall reinforced with conventional steel only. The repair procedure included removal of damaged concrete within the plastic hinge region, replacing fractured and buckled reinforcement, followed by shortening of the SMA reinforcement in the boundary zones of SMA wall. The removed concrete was replaced with self-consolidating concrete, while the concrete above the plastic hinge region remained intact. The SMA reinforced concrete shear wall (before and after repair) exhibited stable hysteretic response with significant strength, and displacement and energy dissipation capacities. In addition, the walls exhibited pinching in the hysteretic response as a result of minimizing the residual displacements due to the restoring capacity of the SMA reinforcement. The results demonstrate that SMA reinforced components are self-centering, permitting repairing of damaged areas. Furthermore, the SMA reinforcement is re-usable given its capacity to reset to its original state. The length of the SMA bars in the original and repaired wall, in addition to the presence of starter bars in the original wall, were significant factors in the location of failure of the walls. The conventional steel wall prior to repair was unstable due to large residual displacements experienced during the original test. After repair the wall exhibited ratcheting in hysteretic response but with significant strength. The conventional wall, before and after repair, dissipated more energy than the SMA wall. This was the result of the wider hysteretic loops with reduced punching, but at the cost of large residual displacements. The starter bars in the conventional wall before repair controlled the location of failure, while the presence of couplers in the plastic hinge region was the main factor in determining the failure location in the repaired conventional wall.

In this research, monotonic and cyclic tests on cold-formed steel shear walls sheathed with steel sheets on one side were conducted to (1) verify the published nominal shear strength for 18-mil and 27-mil steel sheets; and (2) investigate the behavior of 6-ft. wide shear walls with multiple steel sheets. In objective 1: this research confirms the discrepancy existed in the published nominal strength of 27-mil sheets discovered by the previous project and verified the published nominal strength of 18 mil sheet for the wind design in AISI S213. The project also finds disagreement on the nominal strength of 18-mil sheets for seismic design, which is 29.0% higher than the published values. The research investigated 6-ft. wide shear wall with four framing and sheathing configurations. Configuration C, which used detailing, could provide the highest shear strength, compared to Configurations A and B. Meanwhile, the shear strength and stiffness of 2-ft. wide and 4-ft. wide wall can be improved by using the seismic detailing.

This thesis presents two major sections with the objective of introducing a new cold-formed steel (CFS) shear wall system with corrugated steel sheathings. The work shown herein includes the development of an optimal shear wall system as well as an optimal slit configuration for the CFS corrugated sheathings which result in a CFS shear wall with high ductility, high strength, high stiffness and overall high performance. The conclusion is based on the results of 36 full-scale shear wall tests performed in the structural laboratory of the University of North Texas. A variety of shear walls were the subject of this research to make further discussions and conclusions based on different sheathing materials, slit configurations, wall configurations, sheathing connection methods, wall dimensions, shear wall member thicknesses, and etc. The walls were subject to cyclic (CUREE protocol) lateral loading to study their deformations and structural performances. The optimal sit configuration for CFS shear walls with corrugated steel sheathings was found to be 12×2 in. vertical slits in 6 rows. The failure mode observed in this shear wall system was the connection failure between the sheathing and the framing members. Also, most of the shear walls tested displayed local buckling of the chord framing members located above the hold-down locations. The second section includes details of developing a Finite Element Model (FEM) in ABAQUS software to analyze the lateral response of the new shear wall systems. Different modeling techniques were used to define each element of the CFS shear wall and are reported herein. Material properties from coupon test results are applied. Connection tests are performed to define pinching paths to model fasteners with hysteretic user-defined elements. Element interactions, boundary conditions and loading applications are consistent with full scale tests. CFS members and corrugated sheathings are modeled with shell elements, sheathing-to-frame fasteners are modeled using nonlinear springs (SPRING2 elements) for monotonic models and a general user defined element (user subroutine UEL) for cyclic models. Hold-downs are defined by boundary conditions. A total of three models were developed and validated by comparing ABAQUS results to full scale test results.

Wind loads acting on wooden building structures need to be dealt with adequately in order to ensure that neither the serviceability limit state nor the ultimate limit state is exceeded. For the structural designer of tall buildings, avoiding the possibly serious consequences of heavy wind loading while taking account at the same time of the effects of gravitation can be a real challenge. Wind loads are usually no major problem for low buildings, such as one- to two-storey timber structures involving ordinary walls made by nailing or screwing sheets of various types to the frame, but when taller structures are designed and built, serious problems may arise. Since wind speed and thus wind pressure increases with height above the ground and the shear forces transmitted by the walls increase accordingly, storey by storey, considerable efforts can be needed to handle the strong horizontal shear forces that are exerted on the bottom floor in particular. The strong uplift forces that can develop on the wind side of a structure are yet another matter that can be critical. Accordingly, a structure needs to be anchored to the substrate or to the ground by connections that are properly designed. Since the calculated uplift forces depend very much upon the models employed, the choice of models and simplifications in the analysis that are undertaken also need to be considered carefully. The present licentiate thesis addresses questions of how wind loads acting on multi-storey timber buildings can be best dealt with and calculated for in the structural design of such buildings. The conventional use of sheathing either nailed or screwed to a timber framework is considered, together with other methods of stabilizing timber structures. Alternative ways of using solid timber elements for stabilization are also of special interest. The finite element method was employed in simulating the structural behaviour of stabilizing units. A study was carried out of walls in which sheathing was nailed onto a timber frame. Different structural levels were involved, extending from modelling the performance of a single fastener and of the connection of the sheathing to frame, to the use of models of this sort for studying the overall structural behaviour of wall elements that possess a stabilizing function. The results of models used for simulating different load cases for walls agreed reasonably well with experimental test results. The structural properties of the fasteners binding the sheathing to the frame, as well as of the connections between the members of the frame were shown to have a strong effect on the simulated behaviour of shear wall units. Regarding solid wall panels, it was concluded that walls with a high level of both stiffness and strength can be produced by use of such panels, and also that the connections between the solid wall panels can be designed in such a way that the shear forces involved are effectively transmitted from one panel to the next.