Over the past decade, there has been a growing interest in the devel- opment of integrated circuits (ICs) for wearable or implantable biosensors, aiming at providing personalized healthcare services and reducing the health-care expenses. In biosensor ICs, the analog-to-digital converter (ADC) is a key building block that acts as a bridge between analog signals and digital processors. Since most of the biosensors are attached to or implanted in hu- man bodies and powered by either portable batteries or harvested energy, ultra-low-power operation is often required. The stringent power budget im- poses challenges in designing power-efficient ADCs, especially when targeting high-resolution. Among different ADC architectures, the Sigma-Delta (Σ∆) ADC has emerged as the most suitable for low-power, high-resolution appli- cations. This thesis aims to enhance the power efficiency of continuous-time (CT) incremental Σ∆ (IΣ∆) ADCs by exploring design techniques at both architectural and circuit levels. The impact of feedback DACs in CT IΣ∆ ADCs is investigated, so as to provide power-efficient feedback DAC solutions, suitable for biosensor ap- plications. Different DAC schemes are examined analytically considering the trade-off between timing error sensitivity and power consumption. The an- alytical results are verified through behavioral simulations covering both the conventional and incremental Σ∆ modes. Additionally, by considering a typi- cal biosensor application, different feedback DACs are further compared, aim- ing to offer a reference for selecting a power-efficient DAC scheme. A two-step CT IΣ∆ ADC is proposed, analyzed, implemented and tested, with the objective of offering flexible and power-efficient A/D conversion in neural recording systems. By pipelining two CT IΣ∆ ADCs, the pro- posed ADC can achieve high-resolution without sacrificing the conversion rate. Power-efficient circuits are proposed to implement the active blocks of the proposed ADC. The feasibility and power efficiency of the two-step CT IΣ∆ ADC are validated by measurement results. Furthermore, enhancement techniques from both the architecture and circuit perspectives are discussed and implemented, which are validated by post-layout simulations. A comparative study of several CT IΣ∆ ADC architectures is presented, aiming to boost the power efficiency by reducing the number of cycles per con- version while benefiting from the advantage of CT implementation. Five CT IΣ∆ ADC architectures are analyzed and simulated to evaluate their effective- ness under ideal conditions. Based on the theoretical results, a second-order CT IΣ∆ ADC and an extended-range CT IΣ∆ ADC are selected as implemen- tation case studies together with the proposed two-step CT IΣ∆ ADC. The impact of critical circuit non-idealities is investigated. The three ADCs are then implemented and fabricated on a single chip. Experimental results reveal that the three prototype ADCs improve considerably the power efficiency of existing CT IΣ∆ ADCs while being very competitive when compared to all types of the state-of-the-art IΣ∆ ADCs. / <p>QC 20150422</p>

abstract: Pulse Density Modulation- (PDM-) based class-D amplifiers can reduce non-linearity and tonal content due to carrier signal in Pulse Width Modulation - (PWM-) based amplifiers. However, their low-voltage analog implementations also require a linear- loop filter and a quantizer. A PDM-based class-D audio amplifier using a frequency-domain quantization is presented in this paper. The digital-intensive frequency domain approach achieves high linearity under low-supply regimes. An analog comparator and a single-bit quantizer are replaced with a Current-Controlled Oscillator- (ICO-) based frequency discriminator. By using the ICO as a phase integrator, a third-order noise shaping is achieved using only two analog integrators. A single-loop, singlebit class-D audio amplifier is presented with an H-bridge switching power stage, which is designed and fabricated on a 0.18 um CMOS process, with 6 layers of metal achieving a total harmonic distortion plus noise (THD+N) of 0.065% and a peak power efficiency of 80% while driving a 4-ohms loudspeaker load. The amplifier can deliver the output power of 280 mW. / Dissertation/Thesis / Ph.D. Electrical Engineering 2011

Harmonic distortions are inevitably caused by a rectifier and an inverter due to their inherent nonlinearities. An AC-DC-AC converter, configured by the series connection of a rectifier, DC link, and an inverter, induces harmonic distortions at both AC sides and at the DC link. These harmonics can nonlinearly interact or modulate the fundamental frequencies at the AC sides to cause interharmonic distortions. Harmonic and interharmonic distortions can seriously hamper the normal operation of the power system by means of side effects such as excitation of undesirable electrical and/or mechanical resonances, misoperation of control devices, and so forth. This dissertation presents effective methodologies to mitigate harmonic and interharmonic distortions by applying dithered pulse-width modulated (PWM) signals to a voltage-sourced inverter (VSI) type adjustable speed drive (ASD). The proposed methods are also efficient because the dithering applications are performed on control signals without the need for additional devices. By the help of dithering, the rejection bandwidth of a harmonic filter can be relaxed, which enables a lower-order configuration of harmonic filters. First, this dissertation provides a dithering application on gating signals of a sinusoidal PWM (SPWM) inverter in the simulated VSI-ASD model. The dithering is implemented by adding intentional noise into the SPWM process to randomize rising and falling edges of each pulse in a PWM waveform. As a result of the randomized edges, the periodicity of each pulse is varied, which result in mitigated harmonic tones. This mitigation of PWM harmonics also reduces associated interharmonic distortions at the source side of the ASD. The spectral densities at harmonic and interharmonic frequencies are quanti fied by Fourier analysis. It demonstrates approximately up to 10 dB mitigation of harmonic and interharmonic distortions. The nonlinear relationship between the mitigated interharmonics and harmonics is confirmed by cross bicoherence analysis of source- and DC-side current signals. Second, this dissertation proposes a dithered sigma-delta modulation (SDM) technique as an alternative to the PWM method. The dithering method spreads harmonic tones of the SD M bitstream into the noise level. The noise-shaping property of SDM induces lower noise density near the fundamental frequency. The SDM bitstream is then converted into SDM waveform after zero-order interpolation by which the noise-shaping property repeats at every sampling frequency of the bitstream. The advantages of SDM are assessed by comparing harmonic densities and the number of switching events with those of SPWMs. The dithered SD M waveform bounds harmonic and noise densities below approximately -30 dB with respect to the fundamental spectral density without increasing the number of switching events. Third, this dissertation provides additional validity of the proposed method via hardware experiments. For harmonic assessment, a commercial three-phase inverter module is supplied by a DC voltage source. Simulated PWM signals are converted into voltage waveforms to control the inverter. To evaluate interharmonic distortions, the experimental configuration is extended to a VSI-ASD model by connecting a three-phase rectifier to the inverter module via a DC link. The measured voltage and current waveforms are analyzed to demonstrate coincident properties with the simulation results in mitigating harmonics and interharmonics. The experimental results also provide the efficacy of the proposed methods; the dithered SPWM method effectively mitigates the fundamental frequency harmonics and associated interharmonics, and the dithered SDM reduces harmonics with the desired noise-shaping property. / text

Conversores analógico-digitais (ADCs) têm papel fundamental na implementação dos sistemas-em-chip, do inglês System-on-Chip (SoC), atuais. Em razão dos requisitos destes sistemas e dos compromissos entre as características fundamentais dos ADCs, como largura de banda, consumo de energia e exatidão, diversas topologias e estratégias para sua implementação em circuitos integrados (CIs) têm sido desenvolvidas através dos tempos. Dentre estas topologias, os conversores sigma-delta (SDC) têm se destacado pela versatilidade, aliada ao baixo consumo e excelente exatidão. Inicialmente desenvolvidos e empregados para a conversão de sinais de baixa frequência e com operação em tempo discreto (DT), esta classe de conversores têm evoluído e nos últimos anos está sendo desenvolvida para operar em tempo contínuo e ser empregada na conversão de sinais com frequências de centenas de kHz a dezenas de MHz. Neste trabalho, os moduladores sigma-delta em tempo contínuo (SDMs-CT) são estudados, visando sua aplicação à conversão analógico-digital (AD). Os SDMs-CT oferecem vantagens significativas sobre seus homólogos em tempo discreto, como menor consumo de energia, maior largura de banda do sinal de entrada e filtro anti-alias, do inglês anti-alias filter (AAF), implícito. Entretanto, os SDMs-CT apresentam limitações adicionais, responsáveis pela degradação de seu desempenho, como os efeitos do jitter do sinal de relógio, o atraso excessivo do laço de realimentação, do inglês Excess Loop Delay (ELD), e as limitações impostas aos integradores analógicos. Após o estudo e análise de SDMs-CT e de suas limitações, foi desenvolvido um modelo comportamental no ambiente Matlab/Simulink R , que permite a simulação do impacto destas limitações no modulador, possibilitando a obtenção de uma estimativa mais aproximada do seu desempenho. Com base nestas simulações foi possível a determinação das especificações mínimas de cada bloco analógico que compõe o modulador (como o slew rate, a frequência de ganho unitário (fu) e o ganho DC dos amplificadores operacionais utilizados nos integradores) e os valores toleráveis de ELD e jitter do sinal de relógio. Adicionalmente, neste trabalho foi desenvolvida uma metodologia para simulação de SDMs-CT compostos por DACs a capacitor chaveado e resistor, do inglês Switched-Capacitor-Resistor (SCR). Com base neste modelo e no estudo das diferentes topologias de SDMs, um circuito foi desenvolvido para aplicação em receptores de RF, sendo do tipo passa-baixas de laço único, do inglês single-loop, single-bit, de terceira ordem, voltado ao baixo consumo de energia. Este circuito foi desenvolvido em tecnologia CMOS IBM de 130 nanômetros, tendo sido enviado para fabricação. Através das simulações pós-leiaute realizadas espera-se que seu desempenho fique próximo ao que tem sido publicado recentemente sobre SDMs-CT passa-baixas de laço único e single-bit. / Analog-to-Digital Converters (ADCs) play a fundamental role in the implementation of current systems-on-chip (SoC). Due to the requirements of these systems and the tradeoffs between the main ADCs characteristics, such as signal bandwidth, power consumption and accuracy, many topologies and strategies for their implementation in integrated circuits (ICs) have been developed through the ages. Among these topologies, the sigmadelta converters (SDC) have highlighted the versatility combined with low power consumption and excellent accuracy. Initially developed and used for the conversion of low frequency signals and operation in the discrete time (DT) domain, this class of converters have been evolved and developed over the past to operate in continuous time domain for the conversion of signals with frequencies of hundreds of kHz up to tens of MHz. In this work, continuous time sigma-delta modulators (CT-SDMs) are studied focusing its application to the analog-to-digital (AD) conversion. CT-SDMs offer significant advantages over their discrete-time counterparts, such as lower power consumption, higher input signal bandwidth and implicit anti-alias filter (AAF). However, CT-SDMs present additional limitations that are responsible for their performance degradation, such as the clock jitter, Excess Loop Delay (ELD) and the limitations imposed on the analog integrators. After the study and analysis of CT-SDMs and their performance limitations, a behavioral model approach was developed in the Matlab/Simulink R environment, which allows the simulation of the limitations impact on the modulator, allowing the obteinment of a more accurate estimate of its performance. Based on these simulations it was possible to determine the minimum specifications for each block that composes the analog modulator (such as slew rate, the unity gain frequency (fu) and the DC gain of the operational amplifiers used in integrators) and tolerable values of ELD and clock jitter. Additionally, it was developed in this work a methodology for simulate CT-SDMs with Switched-Capacitor- Resistor (SCR) DACs that provide exponential waveforms. Based on this model and the study of different SDMs topologies, it was developed a low-pass, single-loop, single-bit, third order circuit focused on low-power intended for application in RF receivers. This circuit was developed in an IBM 130 nanometers CMOS technology, and was send to manufacturing. Based on the post-layout simulations it is expected to have performance close to what has been recently published of low-pass, single-loop, single-bit CT-SDMs.

Conversores analógico-digitais (ADCs) têm papel fundamental na implementação dos sistemas-em-chip, do inglês System-on-Chip (SoC), atuais. Em razão dos requisitos destes sistemas e dos compromissos entre as características fundamentais dos ADCs, como largura de banda, consumo de energia e exatidão, diversas topologias e estratégias para sua implementação em circuitos integrados (CIs) têm sido desenvolvidas através dos tempos. Dentre estas topologias, os conversores sigma-delta (SDC) têm se destacado pela versatilidade, aliada ao baixo consumo e excelente exatidão. Inicialmente desenvolvidos e empregados para a conversão de sinais de baixa frequência e com operação em tempo discreto (DT), esta classe de conversores têm evoluído e nos últimos anos está sendo desenvolvida para operar em tempo contínuo e ser empregada na conversão de sinais com frequências de centenas de kHz a dezenas de MHz. Neste trabalho, os moduladores sigma-delta em tempo contínuo (SDMs-CT) são estudados, visando sua aplicação à conversão analógico-digital (AD). Os SDMs-CT oferecem vantagens significativas sobre seus homólogos em tempo discreto, como menor consumo de energia, maior largura de banda do sinal de entrada e filtro anti-alias, do inglês anti-alias filter (AAF), implícito. Entretanto, os SDMs-CT apresentam limitações adicionais, responsáveis pela degradação de seu desempenho, como os efeitos do jitter do sinal de relógio, o atraso excessivo do laço de realimentação, do inglês Excess Loop Delay (ELD), e as limitações impostas aos integradores analógicos. Após o estudo e análise de SDMs-CT e de suas limitações, foi desenvolvido um modelo comportamental no ambiente Matlab/Simulink R , que permite a simulação do impacto destas limitações no modulador, possibilitando a obtenção de uma estimativa mais aproximada do seu desempenho. Com base nestas simulações foi possível a determinação das especificações mínimas de cada bloco analógico que compõe o modulador (como o slew rate, a frequência de ganho unitário (fu) e o ganho DC dos amplificadores operacionais utilizados nos integradores) e os valores toleráveis de ELD e jitter do sinal de relógio. Adicionalmente, neste trabalho foi desenvolvida uma metodologia para simulação de SDMs-CT compostos por DACs a capacitor chaveado e resistor, do inglês Switched-Capacitor-Resistor (SCR). Com base neste modelo e no estudo das diferentes topologias de SDMs, um circuito foi desenvolvido para aplicação em receptores de RF, sendo do tipo passa-baixas de laço único, do inglês single-loop, single-bit, de terceira ordem, voltado ao baixo consumo de energia. Este circuito foi desenvolvido em tecnologia CMOS IBM de 130 nanômetros, tendo sido enviado para fabricação. Através das simulações pós-leiaute realizadas espera-se que seu desempenho fique próximo ao que tem sido publicado recentemente sobre SDMs-CT passa-baixas de laço único e single-bit. / Analog-to-Digital Converters (ADCs) play a fundamental role in the implementation of current systems-on-chip (SoC). Due to the requirements of these systems and the tradeoffs between the main ADCs characteristics, such as signal bandwidth, power consumption and accuracy, many topologies and strategies for their implementation in integrated circuits (ICs) have been developed through the ages. Among these topologies, the sigmadelta converters (SDC) have highlighted the versatility combined with low power consumption and excellent accuracy. Initially developed and used for the conversion of low frequency signals and operation in the discrete time (DT) domain, this class of converters have been evolved and developed over the past to operate in continuous time domain for the conversion of signals with frequencies of hundreds of kHz up to tens of MHz. In this work, continuous time sigma-delta modulators (CT-SDMs) are studied focusing its application to the analog-to-digital (AD) conversion. CT-SDMs offer significant advantages over their discrete-time counterparts, such as lower power consumption, higher input signal bandwidth and implicit anti-alias filter (AAF). However, CT-SDMs present additional limitations that are responsible for their performance degradation, such as the clock jitter, Excess Loop Delay (ELD) and the limitations imposed on the analog integrators. After the study and analysis of CT-SDMs and their performance limitations, a behavioral model approach was developed in the Matlab/Simulink R environment, which allows the simulation of the limitations impact on the modulator, allowing the obteinment of a more accurate estimate of its performance. Based on these simulations it was possible to determine the minimum specifications for each block that composes the analog modulator (such as slew rate, the unity gain frequency (fu) and the DC gain of the operational amplifiers used in integrators) and tolerable values of ELD and clock jitter. Additionally, it was developed in this work a methodology for simulate CT-SDMs with Switched-Capacitor- Resistor (SCR) DACs that provide exponential waveforms. Based on this model and the study of different SDMs topologies, it was developed a low-pass, single-loop, single-bit, third order circuit focused on low-power intended for application in RF receivers. This circuit was developed in an IBM 130 nanometers CMOS technology, and was send to manufacturing. Based on the post-layout simulations it is expected to have performance close to what has been recently published of low-pass, single-loop, single-bit CT-SDMs.

Conversores analógico-digitais (ADCs) têm papel fundamental na implementação dos sistemas-em-chip, do inglês System-on-Chip (SoC), atuais. Em razão dos requisitos destes sistemas e dos compromissos entre as características fundamentais dos ADCs, como largura de banda, consumo de energia e exatidão, diversas topologias e estratégias para sua implementação em circuitos integrados (CIs) têm sido desenvolvidas através dos tempos. Dentre estas topologias, os conversores sigma-delta (SDC) têm se destacado pela versatilidade, aliada ao baixo consumo e excelente exatidão. Inicialmente desenvolvidos e empregados para a conversão de sinais de baixa frequência e com operação em tempo discreto (DT), esta classe de conversores têm evoluído e nos últimos anos está sendo desenvolvida para operar em tempo contínuo e ser empregada na conversão de sinais com frequências de centenas de kHz a dezenas de MHz. Neste trabalho, os moduladores sigma-delta em tempo contínuo (SDMs-CT) são estudados, visando sua aplicação à conversão analógico-digital (AD). Os SDMs-CT oferecem vantagens significativas sobre seus homólogos em tempo discreto, como menor consumo de energia, maior largura de banda do sinal de entrada e filtro anti-alias, do inglês anti-alias filter (AAF), implícito. Entretanto, os SDMs-CT apresentam limitações adicionais, responsáveis pela degradação de seu desempenho, como os efeitos do jitter do sinal de relógio, o atraso excessivo do laço de realimentação, do inglês Excess Loop Delay (ELD), e as limitações impostas aos integradores analógicos. Após o estudo e análise de SDMs-CT e de suas limitações, foi desenvolvido um modelo comportamental no ambiente Matlab/Simulink R , que permite a simulação do impacto destas limitações no modulador, possibilitando a obtenção de uma estimativa mais aproximada do seu desempenho. Com base nestas simulações foi possível a determinação das especificações mínimas de cada bloco analógico que compõe o modulador (como o slew rate, a frequência de ganho unitário (fu) e o ganho DC dos amplificadores operacionais utilizados nos integradores) e os valores toleráveis de ELD e jitter do sinal de relógio. Adicionalmente, neste trabalho foi desenvolvida uma metodologia para simulação de SDMs-CT compostos por DACs a capacitor chaveado e resistor, do inglês Switched-Capacitor-Resistor (SCR). Com base neste modelo e no estudo das diferentes topologias de SDMs, um circuito foi desenvolvido para aplicação em receptores de RF, sendo do tipo passa-baixas de laço único, do inglês single-loop, single-bit, de terceira ordem, voltado ao baixo consumo de energia. Este circuito foi desenvolvido em tecnologia CMOS IBM de 130 nanômetros, tendo sido enviado para fabricação. Através das simulações pós-leiaute realizadas espera-se que seu desempenho fique próximo ao que tem sido publicado recentemente sobre SDMs-CT passa-baixas de laço único e single-bit. / Analog-to-Digital Converters (ADCs) play a fundamental role in the implementation of current systems-on-chip (SoC). Due to the requirements of these systems and the tradeoffs between the main ADCs characteristics, such as signal bandwidth, power consumption and accuracy, many topologies and strategies for their implementation in integrated circuits (ICs) have been developed through the ages. Among these topologies, the sigmadelta converters (SDC) have highlighted the versatility combined with low power consumption and excellent accuracy. Initially developed and used for the conversion of low frequency signals and operation in the discrete time (DT) domain, this class of converters have been evolved and developed over the past to operate in continuous time domain for the conversion of signals with frequencies of hundreds of kHz up to tens of MHz. In this work, continuous time sigma-delta modulators (CT-SDMs) are studied focusing its application to the analog-to-digital (AD) conversion. CT-SDMs offer significant advantages over their discrete-time counterparts, such as lower power consumption, higher input signal bandwidth and implicit anti-alias filter (AAF). However, CT-SDMs present additional limitations that are responsible for their performance degradation, such as the clock jitter, Excess Loop Delay (ELD) and the limitations imposed on the analog integrators. After the study and analysis of CT-SDMs and their performance limitations, a behavioral model approach was developed in the Matlab/Simulink R environment, which allows the simulation of the limitations impact on the modulator, allowing the obteinment of a more accurate estimate of its performance. Based on these simulations it was possible to determine the minimum specifications for each block that composes the analog modulator (such as slew rate, the unity gain frequency (fu) and the DC gain of the operational amplifiers used in integrators) and tolerable values of ELD and clock jitter. Additionally, it was developed in this work a methodology for simulate CT-SDMs with Switched-Capacitor- Resistor (SCR) DACs that provide exponential waveforms. Based on this model and the study of different SDMs topologies, it was developed a low-pass, single-loop, single-bit, third order circuit focused on low-power intended for application in RF receivers. This circuit was developed in an IBM 130 nanometers CMOS technology, and was send to manufacturing. Based on the post-layout simulations it is expected to have performance close to what has been recently published of low-pass, single-loop, single-bit CT-SDMs.

About 50 million people worldwide suffer from epilepsy and one third of them have seizures that are refractory to medication. In the past few decades, deep brain stimulation (DBS) has been explored by researchers and physicians as a promising way to control and treat epileptic seizures. To make the DBS therapy more efficient and effective, the feedback loop for titrating therapy is required. It means the implantable DBS devices should be smart enough to sense the brain signals and then adjust the stimulation parameters adaptively. This research proposes a signal-sensing channel configurable to various neural applications, which is a vital part for a future closed-loop epileptic seizure stimulation system. This doctoral study has two main contributions, 1) a micropower low-noise neural front-end circuit, and 2) a low-power configurable neural recording system for both neural action-potential (AP) and fast-ripple (FR) signals. The neural front end consists of a preamplifier followed by a bandpass filter (BPF). This design focuses on improving the noise-power efficiency of the preamplifier and the power/pole merit of the BPF at ultra-low power consumption. In measurement, the preamplifier exhibits 39.6-dB DC gain, 0.8 Hz to 5.2 kHz of bandwidth (BW), 5.86-μVrms input-referred noise in AP mode, while showing 39.4-dB DC gain, 0.36 Hz to 1.3 kHz of BW, 3.07-μVrms noise in FR mode. The preamplifier achieves noise efficiency factor (NEF) of 2.93 and 3.09 for AP and FR modes, respectively. The preamplifier power consumption is 2.4 μW from 2.8 V for both modes. The 6th-order follow-the-leader feedback elliptic BPF passes FR signals and provides -110 dB/decade attenuation to out-of-band interferers. It consumes 2.1 μW from 2.8 V (or 0.35 μW/pole) and is one of the most power-efficient high-order active filters reported to date. The complete front-end circuit achieves a mid-band gain of 38.5 dB, a BW from 250 to 486 Hz, and a total input-referred noise of 2.48 μVrms while consuming 4.5 μW from the 2.8 V power supply. The front-end NEF achieved is 7.6. The power efficiency of the complete front-end is 0.75 μW/pole. The chip is implemented in a standard 0.6-μm CMOS process with a die area of 0.45 mm^2. The neural recording system incorporates the front-end circuit and a sigma-delta analog-to-digital converter (ADC). The ADC has scalable BW and power consumption for digitizing both AP and FR signals captured by the front end. Various design techniques are applied to the improvement of power and area efficiency for the ADC. At 77-dB dynamic range (DR), the ADC has a peak SNR and SNDR of 75.9 dB and 67 dB, respectively, while consuming 2.75-mW power in AP mode. It achieves 78-dB DR, 76.2-dB peak SNR, 73.2-dB peak SNDR, and 588-μW power consumption in FR mode. Both analog and digital power supply voltages are 2.8 V. The chip is fabricated in a standard 0.6-μm CMOS process. The die size is 11.25 mm^2. The proposed circuits can be extended to a multi-channel system, with the ADC shared by all channels, as the sensing part of a future closed-loop DBS system for the treatment of intractable epilepsy.

Les travaux de recherche de cette thèse de doctorat s’inscrivent dans le cadre de la conception d’unconvertisseur analogique-numérique (ADC, Analog-to-Digital Converter) large bande et à haute résolution afinde numériser plusieurs standards de communications sans fil. Il répond ainsi au concept de la radio logiciellerestreinte (SDR, Software Defined Radio). L’objectif visé est la reconfigurabilité par logiciel et l’intégrabilité envue d’un système radio multistandard. Les ADCs à sur-échantillonnage de type sigma-delta () s’avèrent debons candidats dans ce contexte de réception SDR multistandard en raison de leur précision accrue. Bien queleur bande passante soit réduite, il est possible de les utiliser dans une architecture en parallèle permettantd’élargir la bande passante. Nous nous proposons alors dans cette thèse de dimensionner et d’implanter unADC parallèle à décomposition fréquentielle (FBD) basé sur des modulateurs  à temps-discret pour unrécepteur SDR supportant les standards E-GSM, UMTS et IEEE802.11a. La nouveauté dans l’architectureproposée est qu’il est programmable, la numérisation d’un signal issu d’un standard donné se réalise enactivant seulement les branches concernées de l’architecture parallèle avec des sous-bandes defonctionnement et une fréquence d’échantillonnage spécifiée. De plus, le partage fréquentiel des sous-bandesest non uniforme. Après validation du dimensionnement théorique par simulation, l’étage en bande de base aété dimensionné. Cette étude conduit à la définition d’un filtre anti-repliement passif unique d’ordre 6 et detype Butterworth, permettant l’élimination du circuit de contrôle de gain automatique (AGC). L’architectureFBD requière un traitement numérique permettant de combiner les signaux à la sortie des branches enparallèle pour reconstruire le signal de sortie finale. Un dimensionnement optimisé de cet étage numérique àbase de démodulation a été proposé. La synthèse de l’étage en bande de base a montré des problèmes destabilité des modulateurs . Pour y remédier, une solution basée sur la modification de la fonction detransfert du signal (STF) afin de filtrer les signaux hors bande d’intérêt par branche a été élaborée. Unediscontinuité de phase a été également constatée dans le signal de sortie reconstruit. Une solution deraccordement de phase a été proposée. L’étude analytique et la conception niveau système ont étécomplétées par une implantation de la reconstruction numérique de l’ADC parallèle. Deux flots de conceptionont été considérés, un associé au FPGA et l’autre indépendant de la cible choisie (VHDL standard).L’architecture proposée a été validée sur un FPGA Xilinx de type VIRTEX6. Une dynamique de 74 dB a étémesurée pour le cas d’étude UMTS, ce qui est compatible avec celle requise du standard UMTS. / The work presented in this Ph.D. dissertation deals with the design of a wideband and accurate Analog-to-Digital Converter (ADC) able to digitize signals of different wireless communications standards. Thereby, itresponds to the Software Defined Radio concept (SDR). The purpose is reconfigurability by software andintegrability of the multistandard radio terminal. Oversampling  (Sigma Delta) ADCs have been interestingcandidates in this context of multistandard SDR reception thanks to their high accuracy. Although they presentlimited operating bandwidth, it is possible to use them in a parallel architecture thus the bandwidth isextended. Therefore, we propose in this work the design and implementation of a parallel frequency banddecomposition ADC based on Discrete-time  modulators in an SDR receiver handling E-GSM, UMTS andIEEE802.11a standard signals. The novelty of this proposed architecture is its programmability. Where,according to the selected standard digitization is made by activating only required branches are activated withspecified sub-bandwidths and sampling frequency. In addition the frequency division plan is non-uniform.After validation of the theoretical design by simulation, the overall baseband stage has been designed. Resultsof this study have led to a single passive 6th order Butterworth anti-aliasing filter (AAF) permitting theelimination of the automatic gain control circuit (AGC) which is an analog component. FBD architecturerequires digital processing able to recombine parallel branches outputs signals in order to reconstruct the finaloutput signal. An optimized design of this digital reconstruction signal stage has been proposed. Synthesis ofthe baseband stage has revealed  modulators stability problems. To deal with this problem, a solution basedon non-unitary STF has been elaborated. Indeed, phase mismatches have been shown in the recombinedoutput signal and they have been corrected in the digital stage. Analytic study and system level design havebeen completed by an implementation of the parallel ADC digital reconstruction stage. Two design flows havebeen considered, one associated to the FPGA and another independent of the chosen target (standard VHDL).Proposed architecture has been validated using a VIRTEX6 FPGA Xilinx target. A dynamic range over 74 dB hasbeen measured for UMTS use case, which responds to the dynamic range required by this standard.

The aim of this work is to implement digital filters into programmable gate array. The work also includes a description of the MEMS technology, including comparisons with the technology of MEMS microphones from various manufacturers. Another part is devoted to the Sigma-delta modulation. The main section is the design and implementation of digital CIC and FIR filters for signal processing of digital microphone, including simulation and verification of properties of the proposed filter in Matlab.

Dissertation thesis is focused on real digital signal processing by quadrature mirror digital filter banks. In the first part a dual channel quadrature mirror digital filter bank is described briefly. Mainly transfer functions for distorted subband signals are described. In the next part generalized sigma-delta modulator and its linear model are described. Subsequently the generalized sigma-delta modulator is used in decomposition part of quadrature mirror digital filter bank. Designed structure is analyzed. Two design method of transfer functions are designed for the structure on the basis of analysis results. The first method is suitable for hand-made design by intuitive distribution of zeros and poles. The second method is more suitable for computer design. It is iterative method based on correlation. Transfer functions for quadrature mirror digital filter bank with sigma-delta modulators design examples are also part of thesis. Application of designed structure of quadrature mirror digital filter bank can lead to bigger compression ration in lossy data compression.