There is currently a knowledge gap regarding the plastic material properties of many steel types that Atlas Copco use in their high torque power tools. This makes it difficult to fully utilise the capabilities of the Finite Element Method (FEM) to aid the developmental process. Case hardened steel is of special interest as there is not any established method on how to model it numerically.Test specimens of steel type 9195 and 2541 has been developed with two different geometries; hollow and solid. Specimen were heat treated to create case hardened specimens with different Case Depths (CD) as well as specimens made to mimic the material behaviour of the case and core of case hardened steel.Monotone torsion tests were conducted to generate stress-strain data for material models. Hardness tests of case hardened steel were made to determine hardness profiles. By combining these results, a spatially dependent case hardened steel material in an FE-model was created.Test results of the homogeneous specimen tests were successfully modelled using FEA. The case hardened steel could also be modelled, but with a discrepancy against the test results as the model core material were not representative actual core. However, the spatially dependent material model has high potential for simulating the case hardened steel, given the correct inputs. / Det finns för närvarnade bristfällig kännedom gällandes plastiska materialegenskaper hos många av de stål Atlas Copco använder i sina högmomentsverktyg för åtdragning av förband. Detta gör det svårt att fullt ut använda finita elementmetoden (FEM) som ett verktyg i produkters utvecklingsprocess. Sätthärdat stål är av intresse då det inte finns någon etablerad metod för hur det ska modelleras numeriskt.Provstavar gjorda av ståltyperna 9195 och 2541 har tagits fram med två olika geometrier; ihåliga och solida. Provstavarna var värmebehandlade vilket gav sätthärdade material med olika sätthärdningsdjup samt provstavar i material som skulle efterlikna materialet hos höljet och kärnan av sätthärdat stål.Monotona vridprov utfördes för att generera spännings-töjningsdata för användning i materialmodeller. Hårdhetstester gjordes för att fastställa hårdhetsprofiler hos sätthärdat stål. Genom att kombinera dessa provresultat skapades en numerisk material-model av sätthärdat stål med FEM.Testresultaten från de homogena provstavarna återskapades numeriskt med goda resultat. De sätthärdade provstavarnas beteende kunde också återskapas, men med ett något bristfälligt resultat då kärnmaterialet hos modellen inte var representativt av riktigt kärnmaterial hos sätthärdat stål. Modellen har dock hög potential för att återskapa sätthärdat stål, givet korrekt materialdata.

Increasing awareness of sustainable building materials has led to interest in enhancing the structural performance of engineered wood products. Wood is a sustainable, renewable material, and the increasing use of wood in construction contributes to its sustainability. Multi-layer wooden panels are one type of engineered wood product used in construction. There are various techniques to assemble multi-layer wooden panels into prefabricated, load-bearing construction elements. Assembly techniques considered in the earliest stages of this research work were laminating, nailing, stapling, screwing, stress laminating, doweling, dovetailing, and wood welding. Cross-laminated timber (CLT) was found to offer some advantages over these other techniques. It is cost-effective, not patented, offers freedom of choice regarding the visibility of surfaces, provides the possibility of using different timber quality in the same panel at different points of its thickness, and is the most well-established assembly technique currently used in the industrial market. Building upon that foundational work, the operational capabilities of CLT were further evaluated by creating panels with different layer orientations. The mechanical properties of CLT panels constructed with layers angled in an alternative configuration produced on a modified industrial CLT production line were evaluated. Timber lamellae were adhesively bonded in a single-step press procedure to form CLT panels. Transverse layers were laid at a 45° angle instead of the conventional 90° angle with respect to the longitudinal layers’ 0° angle. Tests were carried out on 40 five-layered CLT panels, each with either a ±45° or a 90° configuration. Half of these panels were evaluated under bending: out-of-plane loading was applied in the principal orientation of the panels via four-point bending. The other twenty were evaluated under compression: an in-plane uniaxial compressive loading was applied in the principal orientation of the panels. Quasi-static loading conditions were used for both in- and out-of-plane testing to determine the extent to which the load-bearing capacity of such panels could be enhanced under the current load case. Modified CLT showed higher stiffness, strength, and fifth-percentile characteristics, values that indicate the load-bearing capacity of these panels as a construction material. Failure modes under in- and out-of-plane loading for each panel type were also assessed. Data from out-of-plane loading were further analysed. A non-contact full-field measurement and analysis technique based on digital image correlation (DIC) was utilised for analysis at global and local scales. DIC evaluation of 100 CLT layers showed that a considerable part of the stiffness of conventional CLT is reduced by the shear resistance of its transverse layers. The presence of heterogeneous features, such as knots, has the desirable effect of reducing the propagation of shear fraction along the layers. These results call into question the current grading criteria in the CLT standard. It is suggested that the lower timber grading limit be adjusted for increased value-yield. The overall experimental results suggest the use of CLT panels with a ±45°-layered configuration for construction. They also motivate the use of alternatively angled layered panels for more construction design freedom, especially in areas that demand shear resistance. In addition, the design possibility that such 45°-configured CLT can carry a given load while using less material than conventional CLT suggests the potential to use such panels in a wider range of structural applications. The results of test production revealed that 45°-configured CLT can be industrially produced without using more material than is required for construction of conventional 90°-configured panels. Based on these results, CLT should be further explored as a suitable product for use in more wooden-panel construction. / <p>External cooperation: Martinson Group AB and Research Institutes of Sweden (RISE)</p>