Due to their outstanding properties, poly(arylene ethers) are useful as toughness modifiers in epoxy resins (EP). Furthermore, these polymers show rather low intrinsic fire risks. According to recent research it has been incorporated that poly(arylene ether phosphine oxides) [PAEPO’s] can further improve the fire behavior. Increasing phosphorous content of the PAEPO can influence the fire behavior too. Fire retardants containing phosphorus – regardless of whether an additive or reactive approach is used – show different mechanisms in the condensed and gas phase. In the present study PSU Control (BPA based polysulfone) with four different PAEPO’s and their corresponding blends with an EP were investigated. All poly(arylene ether phosphine oxides) were synthesized by nucleophilic aromatic polycondensation. The polymers obtained covered a wide range of weight average molar masses (6,000 – 150,000 g/mol) as determined by size exclusion chromatography with multi-angle light scattering detection (MALLS). FTIR, NMR spectroscopy and MALDI-TOF revealed formation of the desired polymer structure of the linear poly(arylene ethers). All polymers were easily soluble in common organic solvents, thus enabling processing from solution.The pyrolysis and the fire retardancy mechanisms of the polymers and blends with epoxy resin (EP) were tackled by means of a comprehensive thermal analysis (thermogravimetry (TG), TG-evolved gas analysis) and fire tests [PCFC, limiting oxygen index (LOI), UL-94, cone calorimeter]. The Mitsunobu reaction of Dimethyl-5-hydroxyisophthalate and a long chain semifluorinated alcohol requires triphenyl phosphine as a reactant. Identical, in some case higher yield was obtained in the usual conditions, with triphenyl phosphine and with trivalent phosphorus containing polymers, which was prepared in solvent free bulk (melt) polymerization technique from trivalent phosphorus monomer and a silylated diphenol in presence of CsF. Purification and the recovery of the final product which is always a big challenge in case of Mitsunobu reaction, was far more easier using polymer compared to triphenyl phosphine. During polymerization there was a possibility to have polymer having repeating unit containing both trivalent phosphorus and phosphine oxide. The trivalent phosphorus content of the polymer can be varied using different molar concentration of CsF.

Due to their outstanding properties, poly(arylene ethers) are useful as toughness modifiers in epoxy resins (EP). Furthermore, these polymers show rather low intrinsic fire risks. According to recent research it has been incorporated that poly(arylene ether phosphine oxides) [PAEPO’s] can further improve the fire behavior. Increasing phosphorous content of the PAEPO can influence the fire behavior too. Fire retardants containing phosphorus – regardless of whether an additive or reactive approach is used – show different mechanisms in the condensed and gas phase. In the present study PSU Control (BPA based polysulfone) with four different PAEPO’s and their corresponding blends with an EP were investigated. All poly(arylene ether phosphine oxides) were synthesized by nucleophilic aromatic polycondensation. The polymers obtained covered a wide range of weight average molar masses (6,000 – 150,000 g/mol) as determined by size exclusion chromatography with multi-angle light scattering detection (MALLS). FTIR, NMR spectroscopy and MALDI-TOF revealed formation of the desired polymer structure of the linear poly(arylene ethers). All polymers were easily soluble in common organic solvents, thus enabling processing from solution.The pyrolysis and the fire retardancy mechanisms of the polymers and blends with epoxy resin (EP) were tackled by means of a comprehensive thermal analysis (thermogravimetry (TG), TG-evolved gas analysis) and fire tests [PCFC, limiting oxygen index (LOI), UL-94, cone calorimeter]. The Mitsunobu reaction of Dimethyl-5-hydroxyisophthalate and a long chain semifluorinated alcohol requires triphenyl phosphine as a reactant. Identical, in some case higher yield was obtained in the usual conditions, with triphenyl phosphine and with trivalent phosphorus containing polymers, which was prepared in solvent free bulk (melt) polymerization technique from trivalent phosphorus monomer and a silylated diphenol in presence of CsF. Purification and the recovery of the final product which is always a big challenge in case of Mitsunobu reaction, was far more easier using polymer compared to triphenyl phosphine. During polymerization there was a possibility to have polymer having repeating unit containing both trivalent phosphorus and phosphine oxide. The trivalent phosphorus content of the polymer can be varied using different molar concentration of CsF.