Zugl.: Duisburg, Essen, University, Diss., 2006.

München, Techn. Univ., Diss., 2002. / Computerdatei im Fernzugriff.

München, Techn. Univ., Diss., 2002. / Computerdatei im Fernzugriff.

München, Techn. Universiẗat, Diss., 2004.

München, Techn. Universiẗat, Diss., 2002.

With the recent push towards autonomous cars, a traditional steering wheel with its mechanical connection between the road and driver may soon be unnecessary. To facilitate interior design and lower production costs whilst still maintaining a manual alternative for maneuvering, an alternative steering input device relying on Steer-by-Wire technology is investigated. In order to finish the investigation and development of the steering device within the time-span of a master thesis, the limitation to only investigate the design of a hand wheel was established. The finished alternative steering device utilises an optical encoder for position measurement and a brushless direct current (DC) motor with a planetary gearbox for force feedback. Open-loop speed control proved to be insufficient with the available hardware. Instead, an approach of two PD-controllers regulating the angular error between the steering rack and the steering device was implemented successfully. Initially, mathematical models of the system components were derived and implemented in Mathworks Simulink. The transition from models to test rig implementation proved to be difficult due to unknown parameters in the hardware components such as embedded controllers in the steering gear and the internal works of the sensor emulator used to control the steering gear. By modifying parameters in accordance with system identification measurements performed on the test rig, the models could be validated. At the end of the project, a Volvo S60 was made available and the steering device was tested with real world driving. It was discovered that controllers tuned only for good reference following in the test rig did not translate to good driveability as the controller allowed for overly aggressive maneuvers. Following some in vehicle tuning, the proposed solution performed well during testing with surprisingly high drive-ability. For future iterations of similar hand wheel design projects, a user study was performed with regards to user experience, hand wheel size and perceived driveability.

7th IFAC Symposium on Advances in Automotive Control, The International Federation of Automatic Control, September 4-7, 2013. Tokyo, Japan

Universiẗat, Diss., 2002--Stuttgart.

In the fall of 2004, the High Speed Autonomous Vehicle Team, a group of 16 students took on the goal of converting a vehicle to drive-by-wire status. The main goal of this project was to convert a Cadillac SRX donated by General Motors, to fully by-wire control. This thesis presents the HSAVT brake-by-wire and the steer-by-wire solution. In addition, the results of a literary search on drive-by-wire systems are presented. The results of the project proved that the team came up with a solid, effective drive-by-wire vehicle and that the project met all of the primary goals of the project. / Master of Science

This thesis describes the mechanical design of a prototype vehicle developed for a company located in California. The project was based on an earlier vehicle located at KTH, Transport Labs, and investigated if the existing concept for the vehicle would work as a concept for an autonomous prototype, with focus on component layout and increased forces. The design of the vehicle is based on a concept with a carbon fiber bottom plate, two separate suspension modules with electric hub motors and steer by wire. In addition a steering interface, seats and a roll cage is added to the base. Quadrant symmetric design and four wheel steering/drive makes the vehicle move equally good forward and reverse. The steering is controlled by individual rotating actuators mounted at each wheel, meaning that the vehicle, apart from acquiring a low turning radius also can angle the wheel in the same direction and drive with so called crab steer where the car is moving sideways without rotating itself. The brake system contains a regular manual hydraulic brake system in parallel with an autonomous brake system. The project was started by generating a list of requirements. This was then considered when doing the design in CAD (Solid Edge). The design was validated with ADAMS (MBS) and ANSYS Workbench (FEA). The majority of the project was carried out in Sweden at KTH where the driveline of the vehicle was designed and assembled. The driveline was then transported to California where the vehicle was finalized and tested. The test carried out indicated that the concept was working as a prototype but that some of the components needed to be upgraded. All tests needed was not carried out which led to that the maximum speed of the vehicle was limited to 40 km/h Further durability-, and high load tests will be carried out in order to, with suitable safety, raise the maximum speed. The maximum steering angle of each wheel acquired was 23 degrees that, with four wheel steering, means an effective steering angle of 46 degrees. The cars minimum turning radius was around 5 meters. / Detta examensarbete beskriver den mekaniska konstruktionen av ett prototypfordon för ett företag beläget i Kalifornien. Projektet utgick från ett befintligt fordon på KTH, Transport Labs och undersökte hur vida det befintliga konceptet för det fordonet fungerade för en autonom prototyp, med särskilt hänseende till komponentplacering och ökade krafter. Fordonet är konstruerad runt en bottenplatta av kolfiber, två separata hjulupphängningar med elektriska navmotorer och så kallad ”steer by wire” samt kompletteras med ett förargränssnitt, säten och rullbur. Kvadrant symmetriska design och fyrhjuls styrning/drivning gör att fordonet för sig lika bra framåt som bakåt. Styrningen sköts av en individuell roterande motor fäst vid varje hjul vilket innebär att fordonet, utöver att få en låg svängradie, även kan vinkla alla hjul åt samma håll och uppnå så kallad krabbstyrning där bilen rör sig i sidled utan att själv rotera. Bromssystemet består av ett vanligt manuellt hydrauliskt bromssystem parallell kopplat med ett autonomt aktiverat bromssystem. Projektet inleddes med generering av en kravspecifikation. Denna låg sedan som grund för konstruktionen som genomfördes i Solid Edge (CAD). Konstruktionen validerades med hjälp av ADAMS (MBS) och ANSYS Workbench (FEM). Största delen av projektet genomfördes i Sverige på KTH där drivlinan av fordonets konstruerades och monterads. Denna flögs sedan till Kalifornien där fordonet färdigställdes och testades på plats. De genomförda testerna tydde på att konceptet fungerade bra som prototyp men att vissa komponenter behövde uppgraderas. Full testning han inte genomföras vilket ledde till att den maximala hastigheten begränsades till 40 km/h. Vidare uthållighets- och höglasttester kommer genomföras för att, på ett säkert sätt, kunna öka den maximala tillåtna hastigheten. Den maximala styrvinkeln för varje hjul uppgick till 23 grader vilket, med fyrhjulningsstyrning, innebär en effektiv styrvinkel på 46 grader. Bilens minimi svängradie uppgick till cirka 5 meter.