In this work, an experimental method is developed to study the effects of particle size, flow rate, pulsation, particle/substrate material, and temperature on the short-term reentrainment of submicron particles. The particles tested are in the size range of 10-900 nm and are deposited by wetting the inside of capillary tubes with a liquid suspension. The tubes are then dried in a desiccator. The particles are reentrained under turbulent dry air flow conditions and a condensation particle counter is used to measure the number of entrained particles.There has been very limited work done with nanoscale particles in general and no previous experimental work has reported about this particular parameter set. In order to interpret the data, a bimodal lognormal probability density for the ratio of adhesion force to removal forces is suggested. The majority of particles is attached to the surface by strong forces and cannot be entrained. However, a small fraction of particles, called loose particles, is attached to the surface by much smaller forces. Based on experimental data, an analytical equation for the fraction of loose particles in terms of a dimensionless force is developed. This dimensionless force is a function of particle size and gas flow rate. The temporal variations of fraction of deposited particles are calculated by incorporating the fraction of loose particles with the model of Wen and Kasper (1989).The experimental data confirmed the theoretical expectation that entrainment strongly depends on particle size and decreases as the size of the particle decreases. Both higher flow rates and pulsation of the flow increase the entrainment. Pulsation causes the distribution of forces to broaden. It is shown that the effect of particle/substrate material on entrainment can be predicted by the compound Hamaker constant provided that the morphology and the roughness of the system remain the same. Otherwise, the effect of roughness or morphology may override the effect of Hamaker constant.

Severe plastic deformation (SPD) has been used over the past few decades for producing submicron grain (SMG) structures in range of metals and alloys. Equal channel angular pressing (ECAP) is a useful process for producing these types of structures whereby the material is deformed to very high plastic strains by passing a billet several times through the ECAP die. This process has an added advantage maintaining the initial dimensions of the billet. SMG materials produced by ECAP and related routes are useful as they usually exhibit excellent properties including high strength and hardness, and excellent superplastic formability: these and other properties make SMG materials useful for industrial and aerospace applications. In this thesis, a binary aluminium alloy containing a very low concentration of scandium (0.1 wt. %) Sc alloy was investigated and compared with higher Sc-containing alloys. The material was deformed by ECAP in the solution treated condition to an equivalent von Mises strain of 9.2 then pre-aged at 250 0C to generate a submicron grained material containing a relatively uniform dispersion of nanosized Al3Sc dispersiods. The thermal stability of this pre-aged microstructure was investigated by annealing at temperatures up to 450 0C resulted in continuous grain coarsening by the process of continuous recrystallization whereby the initial microstructure evolves gradually with no marked change in the grain size distribution, texture and grain boundary character. However, extended annealing (> 1h) at 4500 C resulted in discontinuous grain coarsening (often termed recrystallization) whereby a few grains grow rapidly to eventually produce a coarse-grained final microstructure. Throughout annealing, there was a good correlation between the dispersion parameter, (f/d) where f and d is the volume fraction and the mean diameter of Al3Sc particles in the alloy, respectively, and both the mean grain size (D ) and D /D max where max D is the maximum grain diameter observed in the microstructure. The grain structure was found to undergo moderate coarsening at the high f/d-values but converted to a coarsegrained structure for f/d ~<0.5/μm, and this change occurred when the mean grain diameter was ~ 3-4μm. Hence, the critical value of the dispersion parameter for the transition from continuous to discontinuous coarsening falls between the theoretical value for submicron grain size alloys (f/d ~ 1.5/μm) and the value found for conventionally-deformed alloys (f/d ~ 0.1/μm). This behaviour is the result of the alloy no longer being ultra-fine grained at the onset of discontinuous coarsening.

Severe plastic deformation (SPD) has been used over the past few decades for producing submicron grain (SMG) structures in range of metals and alloys. Equal channel angular pressing (ECAP) is a useful process for producing these types of structures whereby the material is deformed to very high plastic strains by passing a billet several times through the ECAP die. This process has an added advantage maintaining the initial dimensions of the billet. SMG materials produced by ECAP and related routes are useful as they usually exhibit excellent properties including high strength and hardness, and excellent superplastic formability: these and other properties make SMG materials useful for industrial and aerospace applications. In this thesis, a binary aluminium alloy containing a very low concentration of scandium (0.1 wt. %) Sc alloy was investigated and compared with higher Sc-containing alloys. The material was deformed by ECAP in the solution treated condition to an equivalent von Mises strain of 9.2 then pre-aged at 250 0C to generate a submicron grained material containing a relatively uniform dispersion of nanosized Al3Sc dispersiods. The thermal stability of this pre-aged microstructure was investigated by annealing at temperatures up to 450 0C resulted in continuous grain coarsening by the process of continuous recrystallization whereby the initial microstructure evolves gradually with no marked change in the grain size distribution, texture and grain boundary character. However, extended annealing (> 1h) at 4500 C resulted in discontinuous grain coarsening (often termed recrystallization) whereby a few grains grow rapidly to eventually produce a coarse-grained final microstructure. Throughout annealing, there was a good correlation between the dispersion parameter, (f/d) where f and d is the volume fraction and the mean diameter of Al3Sc particles in the alloy, respectively, and both the mean grain size (D ) and D /D max where max D is the maximum grain diameter observed in the microstructure. The grain structure was found to undergo moderate coarsening at the high f/d-values but converted to a coarsegrained structure for f/d ~<0.5/μm, and this change occurred when the mean grain diameter was ~ 3-4μm. Hence, the critical value of the dispersion parameter for the transition from continuous to discontinuous coarsening falls between the theoretical value for submicron grain size alloys (f/d ~ 1.5/μm) and the value found for conventionally-deformed alloys (f/d ~ 0.1/μm). This behaviour is the result of the alloy no longer being ultra-fine grained at the onset of discontinuous coarsening.

No description available.

The cement line is the first mineralized matrix deposited on an implant surface during contact osteogenesis forming the bone/implant interface. The hypothesis underlying the present project was that non-collagenous cement line proteins must be deposited into the submicron undercuts on substrate surfaces prior mineralization. In vitro osteogenic cultures were used to grow bone nodules on Thermanox® coverslips modified with calcium phosphate nanocrystals, creating an undercutted surface. Electron microscopy was used to observe cement line formation. BSP immunogold labelling was used to determine if the cement line organic matrix is deposited within undercuts prior mineralization. The results showed the deposited bone nodules, and on test coverslips the deposited cement line was thicker and evenly distributed than control. Furthermore, positive BSP labelling was found within the undercuts prior to cement line mineralization. Thus, it can be concluded that cement line proteins are deposited into submicron undercuts on substrate surfaces prior to mineralization.

The cement line is the first mineralized matrix deposited on an implant surface during contact osteogenesis forming the bone/implant interface. The hypothesis underlying the present project was that non-collagenous cement line proteins must be deposited into the submicron undercuts on substrate surfaces prior mineralization. In vitro osteogenic cultures were used to grow bone nodules on Thermanox® coverslips modified with calcium phosphate nanocrystals, creating an undercutted surface. Electron microscopy was used to observe cement line formation. BSP immunogold labelling was used to determine if the cement line organic matrix is deposited within undercuts prior mineralization. The results showed the deposited bone nodules, and on test coverslips the deposited cement line was thicker and evenly distributed than control. Furthermore, positive BSP labelling was found within the undercuts prior to cement line mineralization. Thus, it can be concluded that cement line proteins are deposited into submicron undercuts on substrate surfaces prior to mineralization.

Using an innovative arrangement of instruments to obtain a comprehensive set of properties, we present a description of the submicron aerosol properties for two distinct regions. During the 2009 SHARP/SOOT campaign in Houston, TX, the average effective density was 1.54 ± 0.07 g cm^-3, consistent with a population comprised largely of sulfates and organics Even in low concentrations (0.31 ± 0.22 µg m^-3), black carbon concentration has a significant impact on the overall density and optical properties. Under prevailing northerly winds, the average black carbon concentration increases from 0.26 ± 0.18 µg m^-3 to 0.60 ± 0.21 µg m^-3. Throughout the campaign, aerosols are often internally mixed, with one peak in the effective density distribution located at 1.55 ± 0.07 g cm^-3. In addition, we conclude that in this region the meteorology has a discernible impact on the concentration and properties of aerosols. After a frontal passage, there is a significant shift in the size distribution as the concentration of <100 nm particles increase and the average effective density decreases to 1.43 ± 0.08 g cm^-3. In Tijuana, Mexico, the submicron aerosols are heavily influenced by vehicle emissions. We observe an average single scattering albedo of 0.75. This average SSA is lower than observed in many US urban environments, and indicates a high concentration of black carbon. The average black carbon concentration is 2.71 ± 2.65 g cm^-3. The aerosol size distributions reveal a high concentration of small particles (< 100 nm) during the day, which are frequently associated with vehicle emissions. Overall, 46 and 81 nm particles are hydrophobic, have an average effective near 1.30 g cm^-3, a higher volatile growth factors than the larger particles, and exhibit a distinct diurnal cycle, which, on average, ranges between 0.80 during the afternoon and 1.70 g cm^-3 overnight. 46 and 81 nm distributions indicate a uniform aerosol composition. 151 and 240 nm aerosols are less cyclical, and the hygroscopicity, volatility, and effect density distributions all exhibit a bimodal distribution, which indicates an external mixture of aerosols. Black carbon and vehicle and industrial organic emissions appear to be the main components of the external mixture.

The sintering behavior to form TiC-Ni-Mo cermet using a nano-size TiC powders was investigated in flowing Argon gas at 1500°C. Nano-sized titanium carbide powders with high purity, high surface area, and low cost were synthesized from carbon coated Ti containing precursors utilizing a patented process. The sintering studies showed that an increase in theoretical density (TD) with increasing molybdenum content. TiC based cermets were characterized using X-ray diffraction (XRD), Vickers hardness, and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS). Mechanical properties, electrical conductivity and oxidation resistance results shows potential applications as interconnect for Low/Intermediate Temperature Solid Oxide Fuel Cells (SOFC) and machining tool tips.

The separation of submicron particles suspended in gaseous flows is a problem of great importance and is the subject of sustained research efforts. This is motivated by several challenges presented by modern science and technology requiring high separation efficiencies for submicron particles.Continuous acoustic particles separation is a novel technique based on the acoustophoresis phenomenon, in which a particle within an acoustic field is manipulated using acoustic forces on its surface. This technique has the potential to overcome some of the limitations of common techniques for the separation of submicron particles, as well as performing advanced tasks such as sorting particles according to their size or density.In this thesis, the separation of submicron solid particles suspended in air is investigated experimentally, with a focus on the effect of key design parameters (acoustic, flow, geometry) on the efficiency of the process. A simple method based on laser light scattering was also used to provide qualitative information on the particle number density as a function of position in the channel. This technique allowed to quickly investigate the effect of a wide range of parameters on the acoustic separation efficiency including the pressure amplitude, the frequency of the standing wave, the average flow velocity and the parallelism of the channel walls.   The results demonstrate conclusively that acoustic manipulation is possible for submicron particles and that the acoustic force scales following the trends expected from theoretical models developed in the continuum regime. From the size of the particles used it however follows that the observed separation is the result of transition regime acoustophoresis, with a Knudsen number on the order of 0.2. / <p>QC 20150522</p>

Understanding the mechanism of bubble-particle interactions plays a critical role in advancing flotation technology. In this study, submicron size bubbles with an average diameter less than 1 μm and a life time of at least several hours were generated using a novel hydrodynamic cavitation method. Effect of mechanical force and water chemistry on generation and stability of submicron size bubbles is investigated. With recent development in measuring zeta potential distributions of colloidal systems, interactions of bubbles and fine solid particles in various electrolyte, surfactant and frother solutions as well as in industrial process water were studied using the stable submicron size bubbles generated by hydrodynamic cavitation. The outcome of this study provides not only a better understanding of bubble-particle attachment mechanism and its role in flotation, but also a direct evidence of armour-coating of bubbles and enhanced bubble-particle interactions by in situ gas nucleation. / Chemical Engineering