Since metals in general, and steels in particular, are vital construction materials in our modern society, the corrosion protection of said materials is of great importance, both to ensure safety and to reduce costs associated to corrosion. Previously, chromium (VI) and other harmful substances were effectively used to provide corrosion protection to steel, but since their use was heavily regulated around year 2000, no coating has yet been developed that, in a fully satisfactory manner, replaces their corrosion protective properties.In this thesis, the use of hydrophobic and superhydrophobic surface coatings as part of corrosion protective coating systems has been studied. Since the corrosion mechanism relies on the presence of water to take place, the use of a superhydrophobic coating to retard the penetration of water to an underlying metal surface is intuitive. The evaluation of corrosion protective properties of the hydrophobic and superhydrophobic surfaces was performed using mainly contact angle measurements and electrochemical measurements in severely corrosive 3 wt% NaCl water solution.First, the differences in corrosion protection achieved when employing different hydrophobic wetting states were investigated using a model alkyl ketene dimer wax system. It was found that superhydrophobicity in the Lotus state is superior to the other states, when considering fairly short immersion times of less than ten days. This is due to the continuous air film that can form between such a superhydrophobic surface and the electrolyte, which can retard the transport of electrolyte containing corrosive ions to the metal surface to the point where the electrical circuit is broken. Since corrosion cannot occur unless an electrical current is flowing, this is a very efficient way of suppressing corrosion.An air layer on an immersed superhydrophobic surface is, however, not stable over long time, and to investigate long-term corrosion protection using hydrophobic coatings a polydimethylsiloxane formulation containing hydrophobic silica nanoparticles was developed. This system showed enhancement in corrosion protective properties with increasing particles loads, up until the point where the particle load instead causes the coating to crack (at 40 wt%). The conclusion is that the hydrophobicity of the matrix and filler, in combination with the elongatedivdiffusion path supplied by the addition of particles, enhanced the corrosion protection of the underlying substrate.To further understand how hydrophobicity and particle addition affect the corrosion protective properties of a coating a three layer composite coating system was developed. Using this coating system, consisting of a polyester acrylate base coating, covered by TiO2 particles (with diameter &lt; 100 nm) and finally coated with a thin hexamethyl disiloxane coating, it was found that both hydrophobicity and particles are needed to reach a great enhancement in corrosion protective properties also for this system. / Eftersom metaller, och då särskilt stål, är viktigta konstruktionsmaterial i vårt moderna samhälle är korrosionsskydd av stor betydelse, både för att garantera säkerhet och för att minska kostnader som uppkommer i samband med korrosion. Tidigare har sexvärt krom och andra skadliga ämnen använts för att på ett effektivt sätt skydda stål från korrosion, men efter att deras användning kraftigt reglerades runt år 2000 har ännu ingen beläggning utvecklats som helt kan ersätta krombeläggningarna med avseende på funktion.I denna avhandling har hydrofoba och superhydrofoba ytbeläggningar och deras möjliga applikation som en del av ett korrosionsskyddande beläggningssystem studerats. Eftersom korrosionsmekanismen är beroende av närvaron av vatten, är användandet av en superhydrofob beläggning för att fördröja transporten av vatten till den underliggande metallytan intuitiv. De korrosionsskyddande egenskaperna hos superhydrofoba ytbeläggningar utvärderades här främst med hjälp av kontaktvinkelmätningar och elektrokemisk utvärdering i korrosiv lösning bestående av 3 vikts% NaCl i vatten.Först undersöktes skillnaden i korrosionsskydd som uppnås vid användandet av ytbeläggningar med olika hydrofoba vätningsregimer med hjälp av ett modellsystem bestående av ett alkylketendimer vax. Det konstaterades att superhydrofobicitet i Lotusregimen är överlägset bättre än de andra hydrofoba vätningsregimerna, i alla fall när man ser till relativt korta exponeringstider, typiskt mindre än tio dagar. Detta beror på att den kontinuerliga luftfilm som kan bildas på en sådan typ av superhydrofob yta kan minska transporten av elektrolyt (som innehåller korrosiva joner) till metallytan till den grad att den elektriska kretsen bryts. Eftersom korrosion inte kan ske utan en sluten elektrisk krets är detta ett mycket effektivt sätt att förhindra korrosion från att ske.Ett luftskikt på en superhydrofob yta nedsänkt i vatten är dock inte stabilt under lång tid. För att undersöka möjligheten till korrosionsskydd under längre tid med hjälp av hydrofoba beläggningar utvecklades en hydrofob ytbeläggning bestående av polydimetylsiloxan och hydrofoba nanopartiklar av kiseldioxid. Detta system visade en förbättring av korrosionsskyddet vid ökat partikelinnehåll upp till den koncentration (40 wt%) där i stället sprickbildning i ytbeläggningen observerades. Från detta system kunde slutsatsen dras att matrisens och partiklarnasvihydrofobicitet i kombination med den längre diffusionsvägen som partiklarna orsakade förbättrade korrosionsskyddet av den underliggande metallen.För att ytterligare förstå hur hydrofobicitet och partikeltillsatser påverkar en ytbeläggnings korrosionsskyddande egenskaper har dessutom ett treskikts kompositbeläggningssystem utvecklats. Genom att använda detta beläggningssystem, som består av en basbeläggning av polyesterakrylat, ett lager TiO2-partiklar (med en diameter på &lt;100 nm) slutligen belagt med ett tunt ytskikt bestående av hexametyldisiloxan så kunde slutsatsen dras att både en hydrofob matris och partiklar behövs för att nå en markant förbättring av ytbeläggningens korrosionsskyddande egenskaper. / <p>QC 20151015</p>

This work has explored the capability of a mixed film composed of oligonucleotides and oligomers to improve the selectivity for the detection of fully complementary oligonucleotide targets in comparison to partially complementary targets which have one and three base-pair mismatched sites. The intention was to introduce a “matrix isolation” effect on oligonucleotide probe molecules by surrounding the probes with oligomers, thereby reducing oligonucleotide-to-oligonucleotide and/or oligonucleotide-to-surface interactions. This resulted in a more homogeneous environment for probes, thereby minimizing the dispersity of energetics associated with formation of double-stranded hybrids. The mixed film was constructed by immobilizing pre-synthesized oligonucleotides onto a mixed aminosilane layer and then growing the oligomer portion by surface-initiated atom transfer radical polymerization (ATRP) of 2-hydroxy methacrylate (PHEMA). The performance of the mixed film was compared to films composed of only oligonucleotides in a series of hybridization and melt curve experiments. Surface characterization techniques were used to confirm the growth of the oligomer portion as well as the presence of both oligonucleotides and oligomer components. Polyatomic bismuth cluster ions as sources for time-of-flight secondary ion mass spectrometry experiments could detect both components of the mixed film at a high sensitivity even though the oligomer portion was at least 200-fold in excess. At the various ionic strengths investigated, the mixed films were found to increase the selectivity for fully complementary targets over mismatched targets by increasing the sharpness of melt curves and melting temperature differences (delta Tm) by 2- to 3-fold, and by reducing non-specific adsorption. This resulted in improved resolution between the melt curves of fully and partially complementary targets. A fluorescence lifetime investigation of the Cy3 emission demonstrated that Cy3-labeled oligonucleotide probes experienced a more rigid microenvironment in the mixed films. These experiments demonstrated that a mixed film composed of oligonucleotides and PHEMA can be prepared on silica-based substrates, and that they can improve the selectivity for SNP discrimination compared to conventional oligonucleotide films.

This research develops an analytical scientific approach for investigating the high precision surface generation and the quantitative analysis of the effects of direct factors in precision machining. The research focuses on 3D surface characterization with particular reference to the turning process and associated surface generation. The most important issue for this research is surface functionality which is becoming important in the current engineering industry. The surface functionality should match with the characterization parameters of the machined surface, which can be expressed in formula form as proposed in chapter 4. Modelling and simulation are extensively used in the research. The modelling approach integrates the cutting forces model, thermal mode% vibration model, tool wear model, machining system response model and surface topography model. All of those models are integrated as a whole model. The physical model with such as direct inputs is formed. The major inputs to the model are tooling geometry and the process variables. The outputs from the modelling approach are cutting force, surface texture parameters, dimensional errors, residual stress and material removal rate. MATLAB and Simulink are used as tools to implement the modelling and simulation. According to the simulation results, it is found that the feed rate has the most profound effect on in surface generation. The influence of the vibrations between the cutting tool and the workpiece on the surface roughness may be minimised by the small feed rate and large tool nose radius. Surface functionality simulation has been developed to model and simulate the surface generation in precision turning. The surface functionality simulation model covers the material and tool wear as well. It shows that chip formation is resulted from cutting forces. Cutting trials are conducted to validate the modelling and simulation developed. There are positive results that show the agreement between the simulation and experimental results. The analysis of the results of turning trials and simulations are conducted in order to find out the effects of process variables and tooling characteristics on surface texture and topography and machining instability. From the research, it can be concluded that the investigation on modelling and simulation of precision surfaces generation in precision turning is performed well against the research objectives as proposed. Recommendations for future work are to improve the model parameters identification, including comprehensive tool wear, chip formation and using Neural Networks modelling in the engineering surface construction system.

Metal contamination in groundwater aquifers poses risks to human health as well as other life forms. Previous laboratory experiments have demonstrated that bacteria found in geologic settings like aquifers are likely to adsorb metal contaminants and attenuate metal migration. However, as bacteria can also migrate through the groundwater aquifer a better understanding of the combined effect of these two processes is required. The aim of this laboratory study was to a) explore the affinity bacteria exhibit towards metals and porous media of varying composition, b) investigate the effect of mineral and solution composition on the bacterial filtration and c) use the combined data to predict the impact of microbes on metal mobility in porous media. Pantoea Agglomerans was used as a model bacterium while column materials consisted of quartz sand and iron-oxide coated sand (IOCS). Bacteria were characterised using potentiometric titrations to identify the type and concentration of sites present on their bacterial wall. Particular attention was paid to the effect of kinetics of proton and metal adsorption due to the variable contact times that solutions have with bacteria in columns. It was found that increasing the contact time between cell surfaces and protons during potentiometric titrations resulted in less reproducible results. This was due to the release of cell exudates under high pH conditions rather than cell death. Exudates were also found to adsorb protons. Moreover, zinc adsorption onto cell surfaces is higher after 60 to 90 minutes of contact time, while there is a decline in adsorption for longer contact times due to release of cell exudates in the solution. Stability constants for the adsorption of zinc onto cell surface sites, quartz and IOCS materials were determined through batch adsorption experiments, providing a mechanistic explanation of the adsorption process. Reactive transport models incorporating kinetics and surface complexation are developed to describe zinc movement through packed columns. Batch kinetic studies showed that significant Zn sorption to IOCS takes place gradually during the first two hours of contact time. Adsorption continues to take place at a slower rate for an additional 10 hours. This kinetic effect is manifested also during flow-through experiments (column dimensions: length 0.12 m, diameter 0.025 m) with a Darcian velocity 6.1·10-3 cm s-1, which is comparable to natural groundwater flow rates through sand porous media. A pseudo-second order kinetic adsorption model is combined with a numerical advection dispersion model for the first time to predict Zn transport. Model output results are of mixed quality as the model cannot successfully describe contaminant arrival time and breakthrough curve shape simultaneously. Moreover, a mechanistic surface complexation reactive transport model is capable of predicting Zn sorption under varying pH conditions demonstrating the versatility of mechanistic models. However, these models do not account for kinetics and therefore they are not intended to fit the dispersion of the contaminant due to kinetic effects of adsorption. Experiments in mixed zinc/cell systems demonstrate that transport through IOCS is dominated by the adsorption to the porous medium. This is consistent with the batch surface complexation predictions for the system. Adsorption to bacteria is reversible and zinc is stripped from the cells and redistributed onto the IOCS. Adsorption onto cells becomes significant and plays a role in mobile metal speciation only once the column is saturated with zinc.

INTRODUÇÃO: Superfícies de titânio modificadas por diferentes métodos foram estudadas com base nos parâmetros físicos e químicos de caracterização superficial e sua influência no comportamento de células pré-osteoblásticas (MC3T3) in vitro. MÉTODOS: Discos de titânio comercialmente puro grau II foram submetidos a três métodos de modificação de superfície (polimento, nitretados em plasma em configuração planar e gaiola catódica). As diferentes superfícies foram caracterizadas para observar o efeito do processamento na estrutura da camada superficial, na rugosidade e molhabilidade. Ensaios de adesão e proliferação celular usando linhagens de células pré-osteoblásticas MC3T3 foram realizados para avaliar o efeito das novas superfícies no comportamento celular in vitro. RESULTADOS: Os resultados demonstraram que a nitretação em plasma na configuração de gaiola catódica produz superfícies mais rugosas (p<0,02) e com menores ângulos de contato com a água. CONCLUSÕES: A adesão celular é maior nas superfícies mais rugosas do que nas superfícies polidas (p<0,05) e reagem de modo diferente a composição química do substrato e à topografia da superfície. / PURPOSE: The aim of this study was to evaluated the physico-chemical properties of different titanium surfaces modified by means of low temperature plasma nitridind on rat osteoblast cell adhesion and proliferation. METHODS: Pure Titanium discs grade II was submitted to three different surface preparations (polishing, glow discharge plasma nitriding in planar and cathodic cage configurations). Surface parameters as roughness, wettability and chemichal composition was determined to compare influency of gas mixture on the modified surface material properties. Cellular morphology was observed by scanning electron microscopy. To evaluate the effect of the surface on cellular response, osteoblast cells (MC3T3) adhesion and proliferation was quantified and data analised by Kruskal-Wallis and Friedman statistical tests. RESULTS: plasma nitriding discs shows rougher surfaces( p<0,02) in cathodic cage configuration and lower contact angle values. MC3T3 cells attached on rough surfaces produced by cathodic cage configuration was statistically significant p<0,05 compared to polished discs. CONCLUSIONS: Glow discharge plasma nitriding improve titanium surface roughness and wettability. MC3T3 cell adhesion behavior is related to substrate chemical composition and topography.

Some collision cascades, induced by keV polyatomic projectiles, result in the emission of multiple secondary ions. Such co-emissions imply that the ejecta originate from molecules co-located within the nano-volume perturbed by a single projectile impact. The relevance for the chemical analysis of nano-domains depends on the effectiveness of the projectile to cause co-emission of two or more secondary ions. This research examines how projectile characteristics, i.e. the energy and number of constituent atoms in the projectile, influence multiple secondary ion emission, or "superefficient" events. In addition we examine the relevance of this technique for nanostructure investigation. Yields have been measured for multi-ion emission events as a function of projectile characteristics. The data show that some collision cascades are "superefficient". For example, in a four-ion emission event, the yield for the phenylalanine quasi-molecular ion is two orders of magnitude larger from Au4+ impacts than from equal velocity Au+ projectiles. Yields for the co-emission of two phenylalanine quasi-molecular ions from "super-efficient" events have been measured. This case is particularly productive in that the detection of two analytically significant ions is recorded from a single event. Large increases (one to two orders of magnitude) in co-emitted ion yields were observed with increasing projectile energy and complexity. Correlation coefficients were calculated for the co-emission of two Ph ions, their behavior suggests differences in emission pathways for bombardment by atomic and polyatomic projectiles. Finally, we use this methodology to investigate surface structural effects on the occurrence of "super-efficient" events. The results indicate that it is possible to distinguish between two phases of a chemical compound although the stoichiometry remains the same. These results confirm previous predictions concerning the chemical nature of these "super-efficient" events. Also shown is that they are sensitive to the surface nanoenvironment. This approach extends the technology of Secondary Ion Mass Spectrometry by providing a methodology for probing surface nano-domains at the sub100 nm level.

Electron transfer phenomena in proteins represent one of the most common types of biochemical reactions. They play a central role in energy conversion pathways in living cells, and are crucial components in respiration and photosynthesis. These complex biochemical reaction cascades consist of a series of proteins and protein complexes that couple a charge transfer to different forms of chemical energy. The efficiency and sophisticated optimisation of signal transfer in these natural redox chains has inspired engineering of artificial architectures mimicking essential properties of their natural analogues. Implementation of direct electron transfer (DET) in protein assemblies was a breakthrough in bioelectronics, providing a simple and efficient way for coupling biological recognition events to a signal transducer. DET avoids the use of redox mediators, reducing potential interferences and side reactions, as well as being more compatible with in vivo conditions. However, only a few haem proteins, including the redox protein cytochrome c (cyt.c), and blue copper enzymes show efficient DET on different kinds of electrodes. Previous investigations with cyt.c have mainly focused on heterogeneous electron transfer of monolayers of this protein on gold. An important advance was the fabrication of cyt.c multilayers by electrostatic layer-by-layer self-assembly. The ease of fabrication, the stability, and the controllable permeability of polyelectrolyte multilayers have made them particularly attractive for electroanalytical applications. With cyt.c and sulfonated polyaniline it was for the first time possible that fully electro-active multilayers of the redox protein could be prepared. This approach was extended to design an analytical signal chain based on multilayers of cyt.c and xanthine oxidase (XOD). The system does not need an external mediator but relies on an in situ generation of a mediating radical and thus allows a signal transfer from hypoxanthine via the substrate converting enzyme and cyt.c to the electrode. Another kind of a signal chain is based on assembling proteins in complexes on electrodes in such a way that a direct protein-protein electron transfer becomes feasible. This design does not need a redox mediator in analogy to natural protein communication. For this purpose, cyt.c and the enzyme bilirubin oxidase (BOD, EC 1.3.3.5) are co-immobilized in a self-assembled polyelectrolyte multilayer on gold electrodes. Although these two proteins are not natural reaction partners, the protein architecture facilitates an electron transfer from the electrode via multiple protein layers to molecular oxygen resulting in a significant catalytic reduction current. Finally, we describe a novel strategy for multi-protein layer-by-layer self-assembly combining cyt.c with an enzyme sulfite oxidase (SOx) without use of any additional polymer. Electrostatic interactions between these two proteins with rather separated pI values during the assembly process from a low ionic strength buffer were found sufficient for the layer-by-layer deposition of the both biomolecules. It is anticipated that the concepts described in this work will stimulate further progress in multilayer design of even more complex biomimetic signal cascades taking advantage of direct communication between proteins. / Elektronentransferphänomene in Proteinen stellen den häufigsten Typ biochemischer Reaktionen dar. Sie spielen eine zentrale Rolle bei der Energieumwandlung in der Zelle und sind entscheidende Komponenten in der Atmung und Photosynthese. Diese komplexen Kaskaden biochemischer Reaktionen setzen sich aus einer Reihe von Proteinen und Proteinkomplexen zusammen, die den Energietransfer an verschiedene Formen chemischer Energie koppeln. Die große Effektivität und Selektivität des Signaltransfers in diesen natürlichen Redoxketten war Vorbild für die Entwicklung künstlicher Architekturen, die die wesentlichen Eigenschaften ihrer natürlichen Analoga nachahmen. Die Implementierung des direkten Elektronentransfers (DET) von Proteinen mit Elektroden war ein Durchbruch im Bereich der Bioelektronik. Sie lieferte einen einfachen und effizienten Weg für das Koppeln biologischer Erkennungsereignisse an einen Signalumwandler. Durch den DET können Redoxmediatoren vermieden und damit potentielle Grenzflächen und Nebenreaktionen reduziert werden. Ebenso wird damit die Kompatibilität für in vivo Bedingungen erhöht. Jedoch zeigen nur einige Hämproteine wie das Redoxprotein Cytochrom c (Cyt c) und blaue Kupferproteine einen effizienten DET auf verschiedenen Elektrodentypen. Bisherige Untersuchungen mit Cyt c konzentrierten sich hauptsächlich auf den heterogenen Elektronentransfer von Monoschichten dieses Proteins auf Gold. Ein wichtiger Fortschritt war die Herstellung von Cyt c Multischichten durch die elektrostatische Layer-by-Layer-Technik. Die einfache Herstellung, die Stabilität sowie die kontrollierbaren Permeationseigenschaften von Polyelektrolyt-Multischichten machte sie besonders attraktiv für elektroanalytische Anwendungen. So gelang es auch zum ersten Mal vollständig elektroaktive Multischichten aus Cyt c und Polyanilinsulfonsäure zu präparieren. Dieser Ansatz wurde hier erweitert, um eine analytische Signalkette auf der Basis von Multischichten aus Cyt c und Xanthinoxidase zu entwerfen. Das System bedarf keinen externen Mediator, es hängt jedoch von der in situ Generierung eines vermittelnden Radikals ab und erlaubt daher einen Signaltransfer von Hypoxanthin über ein substratumwandelndes Enzym und Cyt c zur Elektrode. Eine andere Art von Signalketten basiert auf der Assemblierung von Proteinen in Komplexen auf Elektroden in solcher Art und Weise, daß ein direkter Protein-Protein-Elektronentransfer möglich wird. Dieser Ansatz benötigt keinen Redoxmediator in Analogie zu Beispielen aus dem biologischen Signaltransfer. Zu diesem Zweck werden Cyt c und das Enzym Bilirubinoxidase mit einem selbst-assemblierenden Polyelektrolyten auf einer Goldelektrode koimmobilisiert. Obwohl diese zwei Proteine keine natürlichen Reaktionspartner sind, unterstützt die Protein-Architektur einen Elektronentransfer von der Elektrode über mehrere Proteinschichten zu molekularem Sauerstoff und ergibt einen signifikanten katalytischen Reduktionsstrom. Schließlich wird eine neue Strategie beschrieben für eine Selbstassemblierung von Proteinen ohne zusätzlichen Polyelektrolyten - am Beispiel der Kombination von Cyt c mit Sulfitoxidase. Es stellte sich heraus, daß die elektrostatische Wechselwirkung zwischen diesen zwei Proteinen mit ziemlich weit voneinander entfernt liegenden pI-Werten während des Assemblierungsprozesses durch einen Puffer mit geringer Ionenstärke ausreicht um die beiden Biomoleküle nach dem Layer-by-Layer-Prinzip auf einer Elektrode abzuscheiden. Es wird erwartet, daß das entwickelte Konzept von Multiprotein-Assemblaten auf Elektroden weitere Fortschritte bei dem Entwurf von Multischichten und sogar noch komplexeren biomimetischen Signalkaskaden anregen wird und dabei der Vorteil der direkten Kommunikation zwischen Proteinen genutzt wird.

Some collision cascades, induced by keV polyatomic projectiles, result in the emission of multiple secondary ions. Such co-emissions imply that the ejecta originate from molecules co-located within the nano-volume perturbed by a single projectile impact. The relevance for the chemical analysis of nano-domains depends on the effectiveness of the projectile to cause co-emission of two or more secondary ions. This research examines how projectile characteristics, i.e. the energy and number of constituent atoms in the projectile, influence multiple secondary ion emission, or "superefficient" events. In addition we examine the relevance of this technique for nanostructure investigation. Yields have been measured for multi-ion emission events as a function of projectile characteristics. The data show that some collision cascades are "superefficient". For example, in a four-ion emission event, the yield for the phenylalanine quasi-molecular ion is two orders of magnitude larger from Au4+ impacts than from equal velocity Au+ projectiles. Yields for the co-emission of two phenylalanine quasi-molecular ions from "super-efficient" events have been measured. This case is particularly productive in that the detection of two analytically significant ions is recorded from a single event. Large increases (one to two orders of magnitude) in co-emitted ion yields were observed with increasing projectile energy and complexity. Correlation coefficients were calculated for the co-emission of two Ph ions, their behavior suggests differences in emission pathways for bombardment by atomic and polyatomic projectiles. Finally, we use this methodology to investigate surface structural effects on the occurrence of "super-efficient" events. The results indicate that it is possible to distinguish between two phases of a chemical compound although the stoichiometry remains the same. These results confirm previous predictions concerning the chemical nature of these "super-efficient" events. Also shown is that they are sensitive to the surface nanoenvironment. This approach extends the technology of Secondary Ion Mass Spectrometry by providing a methodology for probing surface nano-domains at the sub100 nm level.

Reactive ion scattering spectrometry (RISS) utilizing low energy (tens of eV) polyatomic ions was employed to characterize self-assembled monolayers (SAMs) on gold. The terminal composition of halogenated SAMs, chemisorption motifs of disulfide and diselenide SAMs, and electron transfer properties of molecular wire containing SAMs were interrogated to develop the versatility of RISS as an analytical surface characterization technique.Novel halogen terminated SAMs were examined for their ability to convert translational to vibrational energy of colliding projectile ions. A general increasing energy deposition trend correlated with increasing terminal mass with the exception of the iodine functionality. Increased amounts of surface abstractions and sputtering from C12I suggest competitive ion-surface interactions account for less than predicted energy deposition results. Mixed films of CH2Br and CH3 terminal groups elucidated interfacial surface crowding discerned by energy deposition results.Thiol and disulfide based SAMs were shown by RISS comparisons to be dissimilar in structure. Terminal orientation, however, was the same based on ion-surface reactions, disproving the proposed dimer model of disulfide SAMs. Ion-surface reactions and electron transfer properties of disulfide surfaces suggested greater percentages of c(4x2) superlattice structure than in thiol SAMs. Based on increased hydrogen reactivity, decreased methyl reactivity, and increased energy deposition results, diselenide based SAMs were more disordered than S-Au based SAMs. Electron transfer results monitored through total ion currents (TIC) showed Se-Au contacts are more conductive than S-Au attachments.Molecular wire candidates whose electron transfer capabilities are difficult to characterize by traditional techniques were characterized by RISS after being doped into matrix SAMs. Electron transfer properties were dependent on the isolating SAM matrix, dipole moments of the wires, and the potential applied to the surface. Changes in surface voltage dictated molecular wire geometry and electron transfer. Wires were annealed into preferential geometries by colliding ions, but did not operate as switches.While not related to the advancement of RISS, structural elucidation of the pharmaceutical carvidioliol was investigated by collision-induced dissociation, surface-induced dissociation, sustained off-resonance irradiation, and sustained off-resonance irradiation-resonant excitation and through gas-phase hydrogen/deuterium exchange. This molecule fragmented easily by all methods and demonstrated the chemical specificity of gas-phase hydrogen/deuterium exchange experiments.

Previous experimental and theoretical results indicate that the keys to successful radial lip seals are the surface characteristics of the shaft and the microasperity pattern that develops due to wear on the elastomer. In this study, the lip seal was tested against five different patterns of shaft surface: plain stainless steel, triangular cavities oriented towards air, triangular cavities oriented towards oil, triangular cavities leading and triangular cavities lagging. Using Zygo optical profilometer and scanning electron microscope, a thorough surface characterization of the micro-asperities and microcavities is done on the lip seal elastomer. Correlation coefficients were calculated between the surface parameters of the final shaft surface and elastomer. Although both the surface characteristics of the shaft and the micro-asperities that develop on the elastomer sealing zone are responsible for a successful operation of the lip seal, the deterministic triangular micro-cavity patterns created on the shaft surface dominated the pumping direction with a large variability in the pumping rate. This variability is due to the elastomer wear in. This study also finds a significant correlation between the axial position of minimum roughness on the sealing zone of the elastomer and the pumping rate of the lip seals.