This dissertation presents measurements of unsteady surface pressure on airfoils encountering flow disturbances. Analysis of measurements made on an airfoil immersed in turbulence and comparisons with inviscid theory are presented with the goal of determining the effect of angle of attack on an airfoils inviscid response. Unsteady measurements made on the surface of a linear cascade immersed in periodic flow are presented and analyzed to determine the relationship between the blades inviscid response and tip leakage vortex strength. Measurements of fluctuating surface pressure were made on a NACA 0015 airfoil immersed in grid generated turbulence. The airfoil model has a 2' chord and spans the 6' Virginia Tech Stability Wind Tunnel test section. Two grids were used to investigate the effects of turbulence length scale on the surface pressure response. A large grid which produced turbulence with an integral scale 13% of the chord and a smaller grid which produced turbulence with an integral scale 1.3% of the chord. Measurements were performed at angles of attack from 0 to 20. An array of microphones mounted subsurface was used to measure the unsteady surface pressure. The goal of this measurement was to characterize the effects of angle of attack on the inviscid response. Lift spectra calculated from pressure measurements at each angle of attack revealed two distinct interaction regions; for reduced frequencies < 10 a reduction in unsteady lift of up to 7 decibels (dB) occurs while an increase occurs for reduced frequencies > 10 as the angle of attack is increased. The reduction in unsteady lift at low reduced frequencies with increasing angle of attack is a result that has never before been shown either experimentally or theoretically. The source of the reduction in lift spectral level appears to be closely related to the distortion of inflow turbulence based on analysis of surface pressure spanwise correlation length scales. Furthermore, while the distortion of the inflow appears to be critical in this experiment, this effect does not seem to be significant in larger integral scale (relative to the chord) flows based on the previous experimental work of McKeough (1976) suggesting the airfoils size relative to the inflow integral scale is critical in defining how the airfoil will respond under variation of angle of attack. A prediction scheme is developed that correctly accounts for the effects of distortion when the inflow integral scale is small relative to the airfoil chord. This scheme utilizes Rapid Distortion Theory to account for the distortion of the inflow with the distortion field modeled using a circular cylinder. Measurement of the unsteady surface pressure response of a linear cascade in periodic disturbance is presented. Unsteady pressure was measured on the suction and pressure side of two cascade blades with an array of 24 microphones (12 per blade side) mounted subsurface. The periodic disturbance was generated using a pair of vortex generators attached to a moving end wall. Measurements were made for 8 tip gaps (t/c = 0.00825, 0.0165, 0.022, 0.033, 0.045, 0.057, 0.079, 0.129) and phased averaged with respect to the vortex generator pair position. This measurement was motivated by the results presented by Ma (2003). The work of Ma (2003) suggested that tip leakage vortex shedding in the presence of a periodic disturbance is heavily influenced by the inviscid response of the cascade blade. This conclusion was arrived at by Ma's (2003) observation that as the tip gap is increased the amount of fluctuation in the tip leakage vortex circulation increases dramatically, in fact, many times the circulation in the inflow vortices. Unsteady pressure measurements reveal that the blade response involves a complex interaction of both inviscid response and viscous phenomena. However, a close relationship between unsteady tip loading and tip leakage vortex circulation is revealed suggesting the inviscid response is significant in determining the tip leakage vortex circulation. Additionally, predictions using inviscid theory agree well with measured levels of unsteady tip loading. As such, inviscid theory may be useful for predicting the tip leakage circulation and perhaps, pressure fluctuations in the tip leakage vortex. / Ph. D.

There have been very few studies investigating the rough wall pressure spectra under fully rough flows, which are relevant to many common engineering applications operating within this regime. This investigation uses the Virginia Tech Stability Wind Tunnel to perform experiments on a series of high Reynolds number zero pressure gradient turbulent boundary layers formed over rough walls in an effort to better understand and characterize the behavior of the rough wall pressure spectrum. The boundary layers were fully rough, and the boundary layer height remained sufficiently larger than the height of the roughness elements. Two rough surfaces were tested. One consisted of an array of 1-mm ordered hemispherical elements spaced 5.5-mm apart, and the other contained 3-mm hemispherical elements randomly spaced, but with the same element density as 1/3 of the 1-mm ordered roughness. The wall pressure spectrum and its scaling were then studied in detail, and it was found that the rough wall turbulent pressure spectrum at vehicle relevant conditions is defined by three scaling regions. One of which is a newly discovered high frequency scaling defined by viscosity, but controlled by the friction velocity adjusted to exclude the pressure drag on the roughness elements. Based on these three scaling regions an empirical model describing the wall pressure spectra for hydraulically smooth, traditionally rough, and fully rough flows was explored. Two point wall pressure fluctuations were also analyzed for each surface condition, and it was found that the roughness inhibits the convective velocities within the inner portions of the boundary layer. / Master of Science

Detailed surface pressure measurements have been made on a NACA 0015 immersed in two grid generated homogenous flows at Re = 1.17 x 10⁶ for a = 0°, 4°, 8°, 12°, 16°, and 20°. The goal of this measurement was to reveal and highlight mean loading and turbulence scale effects on surface pressure fluctuations resulting from turbulence/airfoil interaction. Also, measurements are compared with the theory of Amiet (1976a,b). The surface pressure response shows a dependance on angle of attack, the nature of which is related to the relative chord/turbulence scale. The dependance on turbulence scale appears to be non-monotonic at low reduced frequencies, wr = Pi*f*c/U with both an increase and decrease in unsteady pressure magnitude occurring with increasing mean load. A reduced frequency overlap region exists at wr > 10 where the two different scale flows begin to produce similar effects on the surface pressure with increasing angle of attack manifesting as a rise in unsteady surface pressure magnitude. Also, the interaction of the full 3-dimensional wavenumber spectrum affects the distance over which pressure fluctuations correlate and the extent of correlation is affected by angle of attack as demonstrated in the chordwise and spanwise pressure correlation. Amiet's theory is shown to agree favorably with measurements in the leading edge region although demonstrates insufficiencies in predicting unsteady pressure phasing. / Master of Science

Ce travail a porté sur l'étude des propriétés des monocouches de copolymères diblocs neutres-chargés de poly(tert-butylstyrène)/poly(styrène sulfonate) à l'interface eau/air. Conformément aux modèles théoriques, l'étude des isothermes de compression des monocouches a permis de montrer que les chaînes chargées ancrées à l'interface ont une conformation de type brosse osmotique aux aires moléculaires étudiées. Nous montrons aussi l'importance du solvant d'étalement sur les isothermes de pression de surface et une restructuration de l'interface à forte compression qui apparaît sous la forme d'une relaxation de la pression de surface. Les observations de la monocouche par microscopie à l'angle de Brewster et diffusion de rayons X ont révélé l'existence d'une instabilité de flambage de l'interface. Lors de sa compression, l'interface se déforme et laisse apparaître des structures de grandes dimensions (5 à 35 micromètres), aisément observables malgré leur faible amplitude (quelques nanomètres). Nous avons montré que l'apparition du flambage résulte d'un échange de molécules entre l'interface et la sous-phase. Nous avons proposé différents mécanismes de déformation de la monocouche qui permettent de rendre compte qualitativement des différentes caractéristiques du flambage comme la dépendance de la taille des structures avec l'épaisseur de la monocouche, la dépendance de la pression d'apparition des structures avec la concentration en copolymère dans la sous-phase et l'insensibilité au sel. L'impossibilité de mesurer directement l'amplitude des structures à l'interface nous a conduit à développer une nouvelle méthode d'observation des monocouches à l'interface eau/air au moyen d'un microscope à force atomique. Les résultats obtenus sur différentes couches à l'interface eau/air montrent ainsi toutes les potentialités de cette nouvelle technique dans l'observation de monocouches présentant des domaines de taille inférieure à 100 nm.

学位授与大学：京都大学 ; 取得学位: 博士(工学) ; 学位授与年月日: 2007-09-25 ; 学位の種類: 新制・課程博士 ; 学位記番号: 工博第2843号 ; 請求記号: 新制/工/1418 ; 整理番号: 25528 / The unsteady buffeting forces and the gust response prediction of bridges in the atmospheric turbulent flows is recently attracted more attention due to uncertainties in both experiment and analytical theory. The correction functions such as the aerodynamic admittance function and the spatial coherence function have been supplemented to cope with limitations of the quasi-steady theory and strip one so far. Concretely, so-called single-variate quasi-steady aerodynamic admittance functions as the transfer functions between the wind turbulence and induced buffeting forces, as well as coherence of wind turbulence has been widely applied for the gust response prediction. Recent literatures, however, pointed out that the coherence of force exhibits higher than that of turbulence. These correction functions, in the other words, contain their uncertainties which are required to be more understanding. Proper orthogonal decomposition (POD), known as the Karhunen-Loeve decomposition has been applied popularly in many engineering fields. Main advantage of the POD is that the multi-variate correlated random fields/processes can be decomposed and described in such simplified way as a combination of limited number of orthogonally low-order dominant eigenvectors (or turbulent modes) which is convenient and applicable for order-reduced representation, simulation of the random fields/processes such as the turbulent fields, turbulent-induced force fields and stochastic response prediction as well. The POD and its proper transformations based on either zero-time-lag covariance matrix or cross spectral one of random fields/processes have been branched by either the covariance proper transformation (CPT) in the time domain or the spectral proper transformation (SPT) in the frequency domain. So far, the covariance matrix-based POD and its covariance proper transformation in the time domain has been used almost in the wind engineering topics due to its simplification in computation and interpretation. In this research, the unsteady buffeting forces and the gust response prediction of bridges with emphasis on the POD applications have been discussed. Investigations on the admittance function of turbulent-induced buffeting forces and the coherence one of the surface pressure as well as the spatial distribution and correlation of the unsteady pressure fields around some typically rectangular cylinders in the different unsteady flows have been carried out thanks to physical measurements in the wind tunnel. This research indicated effect of the bluff body flow and the wind-structure interaction on the higher coherence of buffeting forces than the coherence of turbulence, thus this effect should be accounted and undated for recent empirical formulae of the coherence function of the unsteady buffeting forces. Especially, the multi-variate nonlinear aerodynamic admittance function has been proposed in this research, as well as the temporo-spectral structure of the coherence functions of the wind turbulence and the buffeting forces has been firstly here using the wavelet transform-based coherence in order to detect intermittent characteristics and temporal correspondence of these coherence functions. In POD applications, three potential topics in the wind engineering field have been discussed in the research: (i) analysis and identification, modeling of unsteady pressure fields around model sections; (ii) representation and simulation of multi-variate correlated turbulent fields and (iii) stochastic response prediction of structures and bridges. Especially, both POD branches and their proper transformations in the time domain and the frequency one have been used in these applications. It found from these studies that only few low-order orthogonal dominant modes are enough accuracy for representing, modeling, simulating the correlated random fields (turbulence and unsteady surface pressure, unsteady buffeting forces), as well as predicting stochastic response of bridges in the time and frequency domains. The gust response prediction of bridges has been formulated in the time domain at the first time in this research using the covariance matrix-based POD and its covariance proper transformation which is very promising to solve the problems of the nonlinear and unsteady aerodynamics. Furthermore, the physical linkage between these low-order modes and physical causes occurring on physical models has been interpreted in some investigated cases. / Kyoto University (京都大学) / 0048 / 新制・課程博士 / 博士(工学) / 甲第13372号 / 工博第2843号 / 新制||工||1418(附属図書館) / 25528 / UT51-2007-Q773 / 京都大学大学院工学研究科社会基盤工学専攻 / (主査)教授 松本 勝, 教授 河井 宏允, 准教授 白土 博通 / 学位規則第4条第1項該当

No description available.

No description available.

Measurements have been performed to understand the sound source mechanism in turbulent boundary layer flow over two and three-dimensional surface discontinuities whose height is smaller than the incoming boundary layer thickness. The work was performed in two different types of boundary layers: a wall-jet flow and a conventional high Reynolds boundary layer. In the wall-jet flow, measurements of far field sound from two-dimensional forward facing steps, gaps with rounded corners and swept forward facing steps with rounded corners were made. The sound from a forward facing step is shown to exhibit effects of non-compactness. Rounding the step corner results in consistent drop in sound levels but the directivity of the sound field remains unchanged. The sound from gaps is dominated by the forward step component and remains unaffected by rounding of the backward step portion. The sound from swept forward facing steps was found to approximately obey an acoustic sweep independence principle up to a sweep angle of 30 deg when the spanwise inhomogeneity in the flow is accounted for using a simple source distribution model. Sweep independence is also observed for steps with corner rounding radii up to 25% of the step height. The work performed in the high Reynolds number boundary layer included measurements on forward facing steps with rounded corners and a three-dimensional circular embossment with the same height as the forward step. The highest Reynolds number based on discontinuity height achieved in this work was approximately 93,000. The results show that rounding the forward step corner has the same qualitative effect on far field sound as in the wall-jet boundary layer. Quantitatively, for similar boundary layer edge velocity the sound is higher than in the wall-jet flow. The near field measurements show that the separation bubble downstream of the step shrinks as the step corner is rounded while the bubble upstream remains unaffected by it. The unsteady surface force in the lower half of the vertical face of the step was found to be independent of corner rounding. The force on the downstream surface shows similar character within the separation bubble for each rounding but decays faster with increasing downstream distance due to reduced bubble size. The unsteady force measurements were applied to the theory of Glegg et al. (2014) and the resultant of the unsteady forces on the vertical face and downstream surface placed at the top corner of the step is shown to qualitatively describe the far field sound. The acoustic sweep independence principle was applied to the far field sound from the circular embossment and it has been shown that the sound from the three-dimensional geometry can be predicted with reasonable accuracy using sound from a two-dimensional forward step with the same span. / Ph. D.

When an aircraft is aerodynamically or structurally damaged in battle, it may not able to complete the mission and the damage may cause its loss. The subject of aircraft battle survivability is one of critical concern to many disciplines, whether military or civil. This thesis considered and focused on Computational Fluid Dynamics [CFD] predictions and experimental investigations into the effects of simulated battle damage on the low-speed aerodynamics of a fmite aspect ratio wing. Results showed that in two-dimensional [2d] and three-dimensional [3D] CFD simulations, Fluent's® models work reasonably well in predicting jets flow structures, pressure distributions, and pressure-coefficient Cp's contours but not for aerodynamic coefficients. The consequences were therefore that CFD prediction was poor on aerodynamic-coefficients increments. The prediction of Cp's achieved good agreement upstream and near the damage hole, but showed poor agreement at downstream of the hole. For the flow structure visualisation, at both weak and strong jet incidences, the solver always predicted pressure-distribution-coefficient lower at upstream and higher at downstream. The results showed relatively good agreement for the case of transitional and strong jet incidences but slightly poor for weak jet incidences. From the experimental results of Finite Wing, the increments for Aspect-ratio, AR6, AR8 and ARIO showed that as damage moves out towards the tip, aerodynamic-coefficients increments i.e. lift-loss and drag-rise decreased, and pitching-moment-coefficient increment indicated a more positive value at all incidence ranges and at all aspect ratios. Increasing the incidence resulted in greater magnitudes of lift-loss and drag-rise for all damage locations and aspect ratios. At the weak jet incidence 4° for AR8 and in all of the three damage locations, the main characteristics of the weak-jet were illustrated clearly. The increments were relatively small. Whilst at 8°, the flow structure was characterised as transitional to stronger-jet. In Finite Wing tests and for all damage locations, there was always a flow structure asymmetry. This was believed to be due to gravity, surface imperfection, and or genuine feature. An 'early strong jet' that indicated in Finite Wing-AR8 at 'transitional' incidence of 8°, also indicated in twodimensional results but at the weak-jet incidence of 4°. For the application of 2d data to AR6, AR8, and ARIO, an assessment of 2d force results led to the analysis that the tests in the AAE's Low Turbulence Tunnel for 2d were under-predicting the damage effects at low incidence, and over-predicting at high incidences. This suggested therefore that Irwin's 2d results could not be used immediately to predict three-dimensional.

No description available.