The dissolution profile of orally delivered drugs can be controlled through the use of osmotically controlled drug delivery devices. The most commonly used device is the osmotic tablet, which is essentially a tablet core that is coated with a rate-limiting semipermeable membrane. The feasibility of applying a coating onto a tablet using dense gas techniques was studied. Two different coating materials, polymethymethacrylate (PMMA, Mw = 120,000 g/mol) and cellulose acetate (CA, 39.8 wt% acetyl content) were applied onto an 8 mm osmotic tablet core using the Gas Anti-solvent (GAS) process. For PMMA, the pressurisation rate, coating temperature and volumetric expansion of up to 250% had minimal effect on the coating quality. The concentration, solvent type and the use of polyethylene glycol (Mw = 200 g/mol) had a more pronounced effect on the coating. The coating process was optimised to apply a smooth and uniform coating with a 50 ??m thickness. For CA, the pressurisation rate and the coating temperature had little effect on the coating that was applied. The process was more sensitive to a change in the concentration of the solution and the volumetric expansion that was used. It was found that the concentration could not be increased too much without affecting the coating quality. A CA coating was applied onto a PMMA-coated tablet using the optimised conditions. The thickness in the tablet coating increased by 10 ??m. Dissolution tests of the uncoated and coated tablets were carried out. The CA coatings were found to be insufficient in limiting the rate of water entering the tablet and performed similarly to an uncoated tablet core. The PMMA coatings were found to limit the rate of delivery of the model drug. However, variations in the PMMA coatings resulted in an inconsistent delivery profile across batches. The tablets coated with both PMMA and CA had a delivery rate in between that of uncoated and PMMA-coated tablets, indicating that the application of the second coating had compromised the initial PMMA coating.

Thesis (M.S.)--Rutgers University, 2006. / "Graduate Program in Pharmaceutical Science." Includes bibliographical references (p. 89-93).

Thesis (Ph. D.)--University of Wisconsin--Madison, 1969. / Typescript. Vita. eContent provider-neutral record in process. Description based on print version record. Includes bibliography.

Drying procedures, like other important unit operations in pharmacy, have received little attention in pharmaceutical literature. Within recent years, however, growing interest in these pharmaceutical engineering areas has become apparent. Fluidization operations, although relatively unexplored in pharmacy, have been firmly established on a broad scale in other industries. Fluidization may be defined as the suspension and agitation of a bed of particulate solids by a vertically rising stream of gas. Each suspended particle is surrounded by the gas. This relative velocity of the gas and solid particles is high, although the gas velocity itself is relatively low. Heat is transferred by by a combination of conduction and convection and by the movement of the solid particles (1). Fluidized bed drying of moist phosphate rock, coal, and many other materials has been discussed in technical literature (1, 2). However, relatively few reports have appeared on the applications of fluidized beds to materials of pharmaceutical interest. These technical studies show that uniform bed temperatures with high heat and mass transfer rates are obtainable in fluidization system. Product temperatures are controllable over narrow limits within the fluidized bed. These reported advantages would appear to have particular importance in processing pharmaceuticals. It is difficult to understand, therefore, why only a few studies on fluidized bed drying have appeared in pharmaceutical literature. Apparently no comprehensive studies dealing with finished tablets, compressed from granulations dried by the fluidization technique, have appeared in pharmaceutical literature. Accordingly, it would seem appropriate that more studies be conducted, in pharmaceutical fields, concerning drying procedures, especially the fluidization process. The present project will consist of conducting a series of tests on identical granule formulations dried by the conventional air drying and oven drying processes as well as the fluidized bed drying technique. The present work will also include the performance of tests on specific physical properties of tablets compressed from the test granulations.

The oral route of drug administration is most extensively used due to the obvious ease of administration. Verapamil hydrochloride is a WHO listed phenylalkylarnine, L-type calcium channel antagonist that is mainly indicated for cardiovascular disorders such as angina pectoris, supraventricular tachycardia and hypertension. Due to its relatively short half-life of approximately 4.0 hours, the formulation of a sustained-release dosage form is useful to improve patient compliance and to achieve predictable and optimized therapeutic plasma concentrations. Direct compression and wet granulation were initially used as methods for tablet manufacture. The direct compression method of manufacture produced tablets that exhibited formulation and manufacturing difficulties. Mini-tablets containing veraparnil hydrochloride were then prepared by wet granulation using Surelease® E-7-19010.and Eudragit® NE 30D as the granulating agents after which the granules were incorporated with an hydrophilic matrix material, Carbopol® 974P NF. Granule and powder blends were evaluated using the angle of repose, loose and tapped bulk density, Can's compressibility index, Hausner's ratio and drug content. Granules with good flow properties and satisfactory compressibility were used for further studies. Tablets were subjected to thickness, diameter and weight variation tests, crushing strength, tensile strength, friability and content uniformity studies. Tablets that showed acceptable pharmaco-technical properties were selected for further analysis. Drug content uniformity and dissolution release rates were determined using a validated isocratic HPLC method. Initially, USP apparatus 1 and 3 dissolution apparatus were used to determine in-vitro drug release rates from the formulations over a 22-hour period. USP apparatus 3 was finally selected as it offers the advantages of mimicking, in part, the changes in the physicochemical environment experienced by products in the gastro-intestinal tract. Differences in release rates between the test formulations and a commercially available product, Isoptin® SR were observed at different pH's using USP apparatus 1. The release of veraparnil hydrochloride from matrix tablets was pH dependent and was markedly reduced at higher pH values. This may be due, in part, to the poor solubility of veraparnil hydrochloride at these pH values and also the possible interaction of verapamil hydrochloride with anionic polymers used in these formulations. Swelling and erosion behaviour of the tablets were evaluated and differences in behaviour were observed which may be attributed to the physico-chemical characteristics of the polymers used in this study. In-vitro dissolution profiles were characterized by the difference (j1) and similarity factor (j2) and also by a new similarity factor, Sct. In addition, the mechanism of drug release from these dosage forms was mainly evaluated using the Korsmeyer-Peppas model and the kinetics of drug release assessed using other models, including Zero order, First order, Higuchi, HixsonCrowell, Weibull and the Baker-Lonsdale model. Dissolution kinetics were best described by application of the Weibull model, and the Korsmeyer-Peppas model. The release exponent, n, confirmed that drug release from these dosage forms was due to the mixed effects of diffusion and swelling and therefore, anomalous release kinetics are predominant. In conclusion, two test batches were found to be comparable to the reference product Isoptin® SR with respect to their in-vitro release profiles.

Beta blockers are commonly prescribed for the chronic treatment of hypertension, one of the most prolific disease states worldwide. The beta blockers selected for this study include acebutolol hydrochloride, labetalol hydrochloride, metoprolol tartrate oxprenolol hydrochloride and propranolol hydrochloride. All of these compounds have a short elimination half-life, necessitating multiple dose per day regimens and therefore the development of sustained release dosage forms incorporating these agents was considered beneficial in terms of extending the dosing interval, with the aim of improving patient compliance and subsequent therapeutic outcomes. Preformulation studies that were conducted included moisture content analysis by Karl Fischer titration, and DSC, a method used to predict potential interactions between the drugs and tablet excipients. Tablets were manufactured by both wet granulation and direct compression techniques, and the resultant drug release characteristics were evaluated using the USP Apparatus 3(BIO.DIS). A validated isocratic HPLC method, capable of separating the five drug candidates simultaneously, was developed and used for the analysis of drug samples. Tablet quality was assessed using analyses that included the physical assessment of weight, diameter, thickness, hardness and friability, as well as content uniformity of tablets, before and after dissolution testing. Direct compression tablet formulations containing each of the five beta blockers were successfully adapted from a prototype wet granulation matrix tablet containing metoprolol tartrate, and various formulation variables were investigated to establish,their effect on the rate and extent of drug release from these tablets. The grade and quantity of ethylcellulose used in the wet granulation and direct compression formulae influenced the release rate of some drug candidates. In addition, an alternative formulation method, involving freeze-drying of the drug with an ethylcellulose dispersion, was shown to have potential for altering release rates further. Anti-frictional agents, talc and colloidal silicon dioxide, did not affect drug release from these matrices,however, they affected the physical character:istics such as tablet weight and thickness, of the resultant tablets. All of the matrix tablets formulated were shown to release drug according to square root of time kinetics, in a sustained manner over a 22 hour period.

Sildenafil citrate (SC) is a phosphodiesterase-5 inhibitor that is used to treat pulmonary hypertension (PH) in paediatric patients. The purpose of these studies was to develop a formulation and manufacture an orodispersible tablet (ODT) that can be easily administered to neonates and children with PH. The advantages of ODT dosage forms include ease of administration, rapid dissolution of the API, SC. Furthermore the dosage form can be taken without water which is beneficial to patients without immediate access to potable fluids. A simple, rapid, accurate, precise and selective reversed-phase HPLC method was developed and validated in accordance with International Conference on Harmonization (ICH) guidelines and was successfully used for the analysis of SC as raw material and in SC containing pharmaceutical dosage forms. Preformulation studies were performed on SC, alone and in combination with potential excipients that could be used to make tablets. Investigations into potential interactions between SC and the excipients were performed using Differential Scanning Calorimetry (DSC) and Infrared Spectroscopy (IR). DSC results revealed that SC was compatible with all potential excipients except mannitol and magnesium stearate. However these interactions were not observed with IR and therefore it was concluded that the interactions were induced by the high temperatures that DSC operates at. Particle size and shape was also established by use of Scanning Electron Microscopy (SEM) and flow properties were monitored by calculating Carr’s Index (CI) and the Hausner Ratio (HR). Direct compression was used as the method of manufacture for SC tablets as this approach is simple and the most economic production approach. The powder blends were assessed for bulk and tapped density and the CI and HR were used to determine the flowability of the blends. The quality attributes of the resultant tablets that were monitored included uniformity of weight, friability, crushing strength, tensile strength, disintegration, wetting and in vitro dispersion times. Design of Experiments is an efficient statistical approach that has become a popular tool used in the pharmaceutical industry to optimize formulation compositions, as it allows for the investigation of several input factors at the same time whilst not using the tedious and traditional “ modification of one variable at a time” approach. A Central composite experimental design was chosen as the most appropriate means to optimize the formulation as it produces more accurate results as opposed to other experimental designs approaches as input factors are investigated at five different levels. Through the use of mathematical modelling, optimum concentrations of disintegrant(s) and an appropriate blending time were established. Analysis of the data from the experimental design and mathematical modelling studies reveal that no changes in disintegrant concentration or blending time altered the disintegration time of the formulation to any significant extent. This result is most likely due to the fact that the critical disintegrant concentration has been reached and increasing the disintegrant concentration further has no effect on disintegration time. It was also established that a change in the concentration of CMS and CRP altered the wetting time of the tablet significantly. Finally it was noted that there was a linear relationship between blending time and the uniformity of content of the tablets produced in these studies. The optimized product was a white tablet with a diameter of 7.31 mm with a thickness of 2.80mm.The dosage form had no visible cracks or evidence of picking or sticking. The tablet exhibits suitable friability and tensile strength while exhibiting a disintegration time of only 8s. Therefore an orodispersible tablet containing SC intended for paediatric use has been successfully developed, manufactured and optimized through the use of preformulation studies, appropriate quality control monitoring and mathematical modelling. These formulations require further optimization in respect of addition of flavours and or additional sweetening agents.

Carbamazepine (CBZ) is a first-line drug used for the treatment of partial and tonic-clonic seizures. It is also the drug of choice for use during pregnancy and recommended for the treatment of seizure disorders in children. CBZ possesses the ability to induce metabolism of drugs that are transformed in the liver and has the unique ability to induce its own metabolism by a phenomenon known as ‘auto- induction’, where its biological half-life is significantly reduced during chronic administration. Large doses of CBZ are often prescribed as daily divided doses and this often adversely affects patient compliance, with the result that therapy is ineffective. A sustained-release dosage form containing CBZ is currently marketed as Tegretol® CR and the development of a generic product would provide patients with an equivalent product with a similar dosing frequency, at a reduced cost. Therefore, the development of a polymer-based matrix tablet was undertaken to produce a sustained-release dosage form of CBZ, since these dosage forms are relatively simple and cheap to produce when compared to other, more sophisticated forms of sustained-release technology. Preformulation studies were conducted to assess moisture content of excipients and dosage forms and to identify possible incompatibilities between CBZ and potential formulation excipients. Furthermore, studies were conducted to assess the potential for polymorphic transitions to occur during manufacture. Stability testing was conducted to assess the behaviour of the dosage forms under storage conditions that the product may be exposed to. Dissolution testing was undertaken using USP Apparatus 3, which allowed for a more realistic assessment and prediction of in vivo drug release rates. Samples were analysed using a high performance liquid chromatographic method that was developed and validated for the determination of CBZ. Tablets were manufactured by wet granulation and direct compression techniques, and the resultant drug release profiles were evaluated statistically by means of the f1 and f2 difference and similarity factors. The f2 factor was incorporated as an assessment criterion in the design of an artificial neural network that was used to predict drug release profiles and formulation composition. A direct compression tablet formulation was successfully adapted from a prototype wet granulation matrix formulation and a number of formulation variables were assessed to establish their effect(s) on the dissolution rate profile of CBZ that resulted from testing of the dosage forms. The particle size grade of CBZ was also investigated and it was ascertained that fine particle size grade CBZ showed improved drug release profiles when compared to the coarse grade CBZ which was desirable, since CBZ is a highly water insoluble compound. Furthermore, the impact of the viscosity grade and proportion of rate-controlling polymer, viz., hydroxypropyl methylcellulose was also investigated for its effect on drug release rates. The lower viscosity grade was found to be more appropriate for use with CBZ. The type of anti-frictional agent used in the formulations did not appear to affect drug release from the polymeric matrix tablets, however specific compounds may have an effect on the physical characteristics of the polymeric tablets. The resultant formulations did not display zero-order drug release kinetics and a first-order mathematical model was developed to provide an additional resource for athematical analysis of dissolution profiles. An artificial neural network was designed, developed and applied to predict dissolution rate profiles for formulation. Furthermore, the network was used to predict formulation compositions that would produce drug release profiles comparable to the reference product, Tegretol® CR. The formulation composition predicted by the network to match the dissolution profile of the innovator product was manufactured and tested in vitro. The formulation was further manipulated, empirically, so as to match the in vitro dissolution rate profile of Tegretol® CR, more completely. The test tablets that were produced were tested in two health male volunteers using Tegretol® CR 400mg as the reference product. The batch used for this “proof of concept” biostudy was produced in accordance with cGMP guidelines and the protocol in accordance with ICH guidelines. The test matrix tablets revealed in vivo bioavailability profiles for CBZ, however, bioequivalence between the test and reference product could not be established. It can be concluded that the polymeric matrix CBZ tablets have the potential to be used as a twice-daily dosage form for the treatment of relevant seizure disorders.

Conventional solid dosage forms often lead to fluctuations which exceed the maximum safe therapeutic level and/or decline below the minimum effective level. It is recognised that many drugs for chronic administration should be administered on a schedule that maintains plasma drug concentration within the therapeutic window. Research in controlled release dosage forms aims at designing a system with a zero-order input (eg, ideally to deliver 8.33% of the dose per hour over a 12 hour duration), producing steady state plasma drug levels. Oral dministration of drugs prepared as a controlled release formulation is extremely popular, and has attracted the attention of pharmaceutical scientists during the last decade. This has been due to the simultaneous convergence of various factors (eg, discovery of novel polymers and devices, better understanding of formulation and physiological constraints, expiration of existing patents, prohibitive cost of developing new drug entities), involved in the development of these delivery systems. Controlled release oral products can be formulated as single or multiple unit dosage forms and the relative merits of multiple unit forms with their own rate controlling systems are well established. This work describes the development of a relatively inexpensive multiple-unit capsule dosage form of theophylline containing coated mini-tablets for drug delivery throughout the gastrointestinal tract. Preformulation studies on theophylline anhydrous included solubility and dissolution rate determinations. Techniques including X-ray powder diffraction, differential scanning colorimetry and infrared spectroscopy provided no evidence of true polymorphism after recrystallisation from various solvents. However, scanning electron micrographs showed the effects of solvent polarity and cooling rate on the size and shape of recrystallised particles. Theophylline granules were manufactured by using various binders and were film coated by fluidised bed technology with various proportions of ethylcellulose, containing varying amounts of PEG 1540. In vitro release rates were dependent upon coating thickness and the proportion of PEG, which, being water soluble, created pores in the coating during dissolution studies as observed by a scanning electron microscope. However, substantial proportions of the drug remained unreleased from the granules. In order to overcome the problems of drug retention, plain granules were used and theophylline mini-tablets (3 mm diameter, weighing 15 - 20 mg) were manufactured and film coated with various Eudragits ® and other polymeric mixtures (soluble and insoluble). In vitro dissolution profiles from samples enclosed in hard gelatin capsules were determined using the USPXXI paddle apparatus in test media at pH 1.2 (HCI), pH 5.4 and 7.4 (phosphate buffers) at 37'C. Monitoring of in vitro theophylline release over 12 h, under identical hydrodynamic conditions, showed that the dissolution rate at pH 1.2 is substantially greater (95% of total drug content released in < 10 h) than that in phosphate buffers. The maximum release after 12 h was approximately 20 and 30% of total drug content of the tablet at pH 5.4 and 7.4, respectively. However, in vivo bioavailability after oral administration of tablets to rabbits corresponded to over 95% of total drug, compared with the same dose administered intravenously. The retarded drug release during in vitro dissolution in phosphate buffer was attributed to a possible interaction of phosphate ions with theophylline molecules at the tablet core-coat interface. These findings indicate that both rate and extent of theophylline release from the slow release coated mini-tablets are highly sensitive to phosphate buffers. The data also emphasise the usefulness of an animal model for assessment of in vivo drug release and subsequent absorption during the development of modified release dosage forms. Mini-tablets were subjected to isothermal and cyclic stresses to reach conditions for up to 6 months at different temperatures and relative humidity. The film integrity was maintained but ageing of the coating occurred which impeded dissolution. Reduced drug release was temperature related while the effect of relative humidi% was insignific~t. Encapsulated mini-tablets (uncoated and coated with Eudragit RL and RS 2% w/w) equivalent to a 300 mg dose, were evaluated both in vitro and in vivo using beagle dogs. The pharmacokinetic parameters from single and multiple dose studies showed several advantages over Theo-Dur® 300 mg tablets. Precise dosage titration is possible by careful adjustment of the number of encapsulated mini-tablets. This multiple unit mini-tablet delivery system will allow for greater flexibility in dosage adjustment compared to the currently available preparations, allowing individualised fine dose titration in those patients requiring therapeutic drug monitoring. The developmentof the multiple unit mini-tablet formulation appears to provide an optimal dosage form with maximum flexibility in respect of dose, duration range and ease of production.

Parmi toutes les voies d’administration, la voie orale a toujours suscité un grand intérêt. Les formes prises par voie orale présentent une grande facilité d’administration pour le patient, tandis que pour les chercheurs, la physiologie du système gastro-intestinal peut être facilement modélisable. Malheureusement, son importante variabilité, liée principalement au temps de vidange gastrique, peut conduire à une mauvaise reproductibilité des effets thérapeutiques et à une diminution de la biodisponibilité. Ce problème est surtout rencontré dans le cas des principes actifs présentant une fenêtre d’absorption étroite au niveau de l’intestin supérieur [Deshpande et col. 1996]. Une solution a été de développer des formes galéniques à libération prolongée caractérisées par un temps de résidence gastrique accru. Ainsi, le principe actif est libéré progressivement en amont de sa fenêtre d’absorption. Dans cette optique, plusieurs systèmes ont été développés :des formes bioadhésives, expansibles, gonflantes ou à hautes densités [Singh et Kim, 2000]. Mais parmi toutes ces formes, ce sont les systèmes flottants qui semblent offrir la protection la plus efficace contre une vidange gastrique précoce [Moës, 1989]. Seth et Tossounian ont ainsi développé une gélule flottante à libération prolongée, basée sur le gonflement d’un dérivé cellulosique. Etant une forme monolithique, sa vidange gastrique était soumise au phénomène de tout ou rien. De plus, cette forme présentait un inconvénient majeur puisqu’elle était sujette à des fractionnements intra-gastriques, diminuant de ce fait la reproductibilité inter- et intra-individuelle [Seth et Tossounian, 1984]. <p>\ / Doctorat en Sciences biomédicales et pharmaceutiques / info:eu-repo/semantics/nonPublished