Shear thickening fluids have the potential to improve the effectiveness of fabric materials in body armor applications as they have shown to increase the puncture and ballistic resistance of Kevlar fabrics. However, the effect of using STFs with natural fabrics such as flax has never been studied. The rheology of STFs at varying concentrations of nanosilica dispersed in polyethylene glycol PEG was studied at different temperatures and it was found that the STFs behave as a non-Newtonian fluid in response to changes in shear rate. In this study the effectiveness on the puncture and ballistic resistance of impregnating flax fabric with STF of nanosilica in PEG were investigated. The effect of hybridization of flax and Kevlar was also investigated. The puncture and ballistic resistance of the samples treated with STFs was found to increase significantly and can be controlled by STF concentration.

Master of Science / Department of Mechanical and Nuclear Engineering / B. Terry Beck / The objective of this project was to first evaluate the feasibility of developing a viscous damping device that used a Non-Newtonian Shear Thickening Fluid (STF) and incorporating it as a door latch into an existing commercial dryer unit. The device would keep the door closed during sudden large magnitude impact loads while still allowing the door to open normally when force is applied gradually at the door handle. The first phase of the project involved performing background research on the subject and performing preliminary analysis in order to determine if the concept was feasible enough to be worth constructing a physical prototype. This preliminary analysis consisted of a literature review of existing damping mechanisms and shear thickening fluids, rheometer testing of shear thickening suspensions to obtain viscosity data, and performing numerical simulations to determine if a damper that fit the size requirements could produce enough resistance force. The focus for the second phase of the project was to demonstrate a proof of concept in the form of a working model prototype. This prototype did not need be of identical shape and proportions as the finalized design, but would be developed to facilitate experimental testing and evaluation of performance under the desired operating conditions. It was also necessary to design and construct the test setup for the dynamic testing of the dryer door opening so that the opening displacement as well as the force applied to the door could be recorded as a function of time. The final phase of the project consisted of improving upon the original prototype in order to prove the validity of a viscous latch beyond the proof of concept phase in a form closer to what is desired for the commercial product. This required reducing the physical size of the new prototype latch so as to fit within the space available in a particular dryer, incorporate a one-way ratcheting device into the latch to allow unrestricted closing of the door, and increase the operational temperature range of the damper.

Algae can be used as a feedstock for agricultural fertilizers, livestock/poultry feeds, anaerobic digestion, and biofuel production. Regardless of the end product, water removal is necessary and difficult to do cost effectively. For each product the requirements for moisture content (or solids content) vary, such that a desirable water removal strategy would need to be adaptable to varying levels of water removal. Flocculation, with sedimentation and drying was evaluated as a possible strategy for algae dewatering. Anionic and nonionic flocculants are known to be ineffective at flocculating algal culture, which was confirmed for this case by electro-osmotic flow testing of the algae and jar tests with three flocculant charge types. Electrophoretic mobility of the algae indicated that it has a negative charge and no flocs were present in the jars. The effectiveness of the cationic flocculant was determined by measuring settling rates, supernatant turbidity, and filtration rates. Sedimentation and filtration rates of Scenedesmus acutus were measured with varying dosages (0-25 ppm) of a synthetic cationic polymeric flocculant. The results of this study should assist in predicting the time it takes to thicken algae at a concentration range of 0.4-1.0 g/L to a product at a concentration range of 15-250 g/L.

No description available.

Much of the discussion of German National Socialism has historically focused on of Adolf Hitler as the architect of the Nazi state. While recognizing Hitler’s central role in the development of National Socialism, this thesis contends that he was not a lone actor. Much of the ideological and structural development National Socialism was driven by senior individuals within the party who were able to leverage their influence to institutionalize personal variants of National Socialism within broader party ideology. To explore the role of other ideologues in the development of Nazi ideology, this thesis examines how Hitler’s leadership style perpetuated factionalism, how when and by whom central elements of Nazi ideology were introduced, as well the ideological sources from which these concepts were adapted. After the party’s ultimate rise to power Hitler, always centrally positioned, eliminated internal competition and institutionalized his own variant of National Socialism whilst co-opting the concepts and structures developed by other ideologues that offered useful tools to pursue his goals. Through this analysis, this thesis seeks to demonstrate how the foundational elements of National Socialism took form, even before the party achieved power, and how these elements were subsequently utilized to consolidate Nazi control over the German state. Above all else, this thesis sheds much-needed light on the pivotal role of individuals and the conflict between them that engineered the cataclysm of the Third Reich.

Hypertension is a risk factor for many cardiovascular and cerebrovascular diseases such as atherosclerosis and stroke. It is therefore important to understand the effect of hypertension on temporal growth and remodeling of arteries. In this study, experimental hypertension was induced in the mini-pig by aortic coarctation. Basilar arteries and aortas were collected for analysis over an eight week period of hypertension with specimens from normotensive animals serving as controls. Changes in mechanical properties of the basilar artery were evaluated by in vitro pressure-diameter tests on intact cylindrical segments at their in situ length. The basilar arteries from hypertensive animals became less distensible, reflecting increases in both structural and material stiffness, compared to their normotensive counterparts. The circumferential stress rapidly returned toward its homeostatic value by increasing the wall thickness within two weeks. Immunohistochemistry, which is capable of illustrating the localization and distribution of protein expression, was performed to examine changes in wall constituents in the aorta. The increased medial thickness observed in hypertensive pigs compared to normotensive pigs was due to hyperplasia of smooth muscle cells (SMCs) and accumulation of extracellular matrix proteins, which were accompanied by the phenotypic modulation of SMCs. The increased interlamellar thickness, collagen fibers, and the thickness of elastic lamina found in the inner media of hypertensive animal may be associated with the gradient of stress decreasing into the outer media. SMC proliferation, if any, was found evenly distributed across the media, however. In cases showing increased proliferation and matrix protein synthesis, the SMC contractile markers were down-regulated whereas the SMC synthetic markers were up-regulated. While the aortic intima appeared normal in the normotensive animals, neointima formation, which may predispose the vessel to atheroma formation, was found in the hypertensive animals. Immunohistochemistry of Hsp47 and procollagen revealed that the endothelial cells (ECs) may produce collagen, specifically type I collagen in response to hypertension and contribute to the thickened intima. In addition, lectin staining for ECs markers and immunostaining for eNOS suggested that endothelial cells may transdifferentiate into intimal SMCs. These findings suggested an alternative role that ECs may play in hypertension-induced atherogenesis.

During the water treatment process, each processing unit releases the sludge from the sedimentation process, and the wastewater from the rapid sand wash and filtration process, to the wastewater pond followed by the wastewater sedimentation pond. The sediment sludge is allowed to enter the sludge thickening pond while the supernatant is recycled for further treatment. The sludge is released to the sludge pond where it is treated with certain chemicals and squeezed to form the sludge cake. The sludge cake is removed and transported by a legitimate cleaning service company to an authorized location. The present study is focused on the investigation of the feasibility of recycling the wastewater and the dewatering of the sludge from the water treatment plant. The analysis of the samples collected from the wastewater treatment plant showed that the recycled supernatant had a pH of 7.16~8.21, a conductivity of 371.1~769.1 £gmho/cm, a total dissolved solid (TDS) of 193.3~399.9 mg/L, and a turbidity of 0.901~54.3 NTU. The suspended solids (SS) of the recycled supernatant was found to be 0.4~45.6 mg/L, lower than the standard value in the Effluent Standards (50 mg/L). The ammonia nitrogen (NH3-N) and the Total Organic Carbon (TOC) of the recycled supernatant were found to be 0.06~1.5 mg/L and 1.533~17.437 mg/L, respectively. The analysis of the Chemical Oxygen Demand (COD) of the wastewater treatment plant showed a concentration of 12.1~128.5 mg/L in the sample of the recycled supernatant. The COD in the Effluent Standards is required to be no more than 100 mg/L. For sludge conditioning and dewatering, a sludge conditioning experiment was conducted in the laboratory to plot the curve of the experimental result. The curve was used for the actual sludge conditioning and dewatering in the Fongshan Water Treatment Plant to verify the feasibility of the application for the actual process in the water treatment plant.

A suspension is a fully saturated mixture of discrete solid particles and interstitial liquid. Examples of suspensions include pastes, slurries, cement, food-spreads, drilling fluids and some geophysical flows. The present work focusses on granular (as opposed to colloidal) suspensions, which we define as those for which the thermal motion of the solid particles is negligible. Despite such ubiquity in industry and nature, our understanding of the mechanical properties of suspensions lags behind that of their constituent solid and liquids. In this thesis, the discrete element method is used to simulate suspension flow in shear, capillary and constriction geometries, mapping and characterising the fundamental flow, or rheological, regimes. As a starting point (Chapter 2), we consider an established regime map for dry granular materials, appropriate for flows of sand, grains and dry debris. Taking guidance from shear flow simulations that consider the lubricating effect of an interstitial liquid, we recast the regime map for a general suspension, elucidating flows comparable to the dry material or to a viscous liquid, dependent on the shear rate, liquid viscosity and particle stiffness. We give an account of the microstructural traits associated with each regime. Motivated by recent groundbreaking theoretical, computational and experimental work, we incorporate the emerging picture of frictional shear thickening into our regime map (Chapter 3). Our shear flow simulations capture the shear thickening behaviour and demonstrate that it may, in principle, occur in any of the identified flow regimes. Our simulations of time-dependent shear flows (Chapter 4), specifically flow reversal, provide a detailed micro-mechanical explanation of a longstanding and previously unexplained experimental finding, guiding future experimentalists in decomposing the particle and liquid contributions to the viscosity of any suspension. Indeed, the findings have already been exploited in the devising of an experimental protocol that has successfully proven the dominance of particle contacts in driving shear thickening. We next consider suspension flow in a microchannel (Chapter 5), finding that the identified shear flow regimes are locally applicable to flows in complex geometries under inhomogeneous stress conditions only when the local mean shear rate exceeds temporal velocity fluctuations. A more comprehensive description is therefore required to fully characterise the flow behaviour in this geometry. Finally (Chapter 6), we simulate pressure driven suspension flow through a constriction geometry, observing highly inhomogeneous stress distributions and velocity profiles. The roles of particle and fluid properties are considered in the context of an industrial paste extrusion process.

Orientador: Ricardo de Lima Isaac / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Civil / Made available in DSpace on 2018-08-05T08:38:56Z (GMT). No. of bitstreams: 1 SilvaJunior_ArchimedesPereirada_M.pdf: 2766426 bytes, checksum: c4a329b55233959c0c769a4fd9c68911 (MD5) Previous issue date: 2003 / Resumo: Os principais resíduos de ETAs são os Iodos gerados nos decantadores, a água de lavagem dos filtros e o rejeito de limpeza dos tanques de produtos químicos. Os lodos mesmo classificados como resíduos sólidos, apresentam baixíssimo teor de sólidos. Sendo o custo do transporte e disposição final bastante elevado, a redução do volume constitui-se em alternativa, economicamente, viável. Os principais processos utilizados para redução de volume do Iodo são o adensamento, o condicionamento químico e a desaguamento. A pesquisa teve por objetivo comparar a tratabilidade do Iodo do decantador do tipo convencional e do decantador de alta taxa, da SANASA, na cidade de Campinas. Foi verificada a influência dos parâmetros que caracterizam a qualidade do Iodo, no seu desaguamento; o efeito do adensamento do Iodo por gravidade, com auxílio de polímeros e o efeito do condicionamento químico com polímeros no desaguamento, por centrifuga. O lodo bruto foi pré-condicionado com polímeros sintéticos, e também se investigou a eficiência destes no condicionamento do lodo já adensado, para sua centrifugação. O adensamento mostrou que o polímero aniônico foi o melhor para ambas as ETAs. A dosagem ótima foi a mesma para ambas as épocas, para as duas ETAs, sendo de 1mg/g para ETA-3 e 3g/Kg para ETA-4. O tempo de mistura, para ETA-3, foi maior na época seca (45s) do que no período de chuvas (30s). Para ETA-4 o tempo de mistura foi o mesmo (60s) para as duas épocas. O lodo adensado foi condicionado com polímero e submetido à centrifugação. Desta, concluiu-se que, para o período de chuvas e para os dois tipos de lodo a condição ótima foi: polímero catiônico, 1g/Kg, 5s de mistura e 200rpm de rotação. Na época de estiagem e lodo da ETA-3 a condição ótima foi dada por: polímero catiônico, 1g/Kg, 60s de mistura e 200rpm de rotação. No caso da ETA-4, a condição é dada por: polímero catiônico, 2,5g/Kg, 60 s de mistura e 100 rpm / Abstract: The main residues of WTPs are sludge from thickener, filter backwash waters and solids from basins of chemicals products. The sludge even labeled as solid residues present very low solids content. Like the costs of transportation and ultimate disposal are very high, to reduce the sludge volume is an economical feasible alternative. The principal methods used to reduce the sludge volume are thickening, chemical conditioning and dewatering. The aim of this research was to compare the handling of both sludge from the conventional and high-rate thickener. It was checked the influence of the parameters that give particular characteristics to the sludge in its dewatering; the gravity thickening with polymers aid and the influence of the polymers in the sludge dewatering with centrifuge. The raw sludge was conditioned with synthetics polymers. Also was checked whether that polymers were efficient in the thickened sludge conditioning aiming its centrifugation. The best polymer to the gravity thickening for both sludge (WTPs 3 and 4) was the anionic polymer. The same polymer dose was required for the both seasons studied (wet and dry) and for the two WTPs. It was 1mg/g to the WTP-3 and it was 3g/Kg to the WTP-4. The mixing time for the WTP-3 was greater in the dry season (45s) than the wet season (30s) and the mixing time was the same (60s) in both seasons for the WTP-4. The thickened sludge was conditioned with organic synthetic polymer and subjected to centrifugation. After this, was concluded that in the wet season and for the two kinds of sludge the optimum condition s given to: cationic polymer, 1g/Kg of polymer dose, mixing time of 5s and 200 rpm of centrifuge rotation. In the dry season and residues from WTP-3 the optimum condition is given to: cationic polymer, 1g/Kg of polymer dose, mixing time of 60s and 200 rpm of centrifuge rotation. For residues from WTP-4 the optimum condition is given to: cationic polymer, 2,5g/Kg of polymer dose, mixing time of 60s and 100 rpm of centrifuge rotation / Mestrado / Saneamento e Ambiente / Mestre em Engenharia Civil

Cette thèse de doctorat a été financée par l’entreprise SIKA spécialisée dans les matériaux de construction. Les trois chapitres de cette thèse correspondent à la tentative de résolution de trois problématiques d’origine industrielle. Dans le premier chapitre, nous avons étudié l’effet de la concentration en particules sur les propriétés d’écoulement de fluides complexes rhéofluidifiants ou rhéoépaississants et démontré l’origine microscopique de cet effet. Dans le second chapitre, nous avons étudié la floculation de particules colloïdales sous faibles perturbations et mis en évidence l’existence, au cours de la reconstruction, d’un maximum du module élastique. Enfin le troisième chapitre est l’étude d’un diagramme de phase de jet de suspensions concentrées. En régime dilué et semi-dilué, les résultats sont conformes à ceux de la bibliographie, en revanche nous avons étudié un nouveau régime à très haute fraction volumique où le jet, instable, se met à osciller. Nous avons montré que ces oscillations étaient dues au rhéoépaississement de la suspension. / This thesis has been done in collaboration with the company SIKA, one of the leader if the construction industry. This thesis report is organized in three chapters where each of them tries to answer a problem coming from industrial processes. In the first chapter, we studied the impact of particles concentration on the flowing properties of complex fluids such as shear-thinning and shear-thickening fluids. We demonstrated the importance of local contacts between particles to explain the evolution of the viscosity with the volume fraction. In the second chapter, we studied the aggregation of colloidal attractive suspensions under small perturbations and proved the existence of a maximum of elastic modulus during the rebuilding of the structure. Finally, the third chapter is a study of a phase diagram of a concentrated suspension jets. In the diluted and semi-diluted regimes, we found results in agreement with the bibliography, meanwhile at very high concentration, we studied a new regime where the jet, unstable, is oscillating. We showed those oscillations can be explained by the shear-thickening behaviour of the suspensions at those high concentrations.