No description available.

Current Source Inverter (CSI) topology is gaining acceptance as a competitive alternative for grid interface of renewable energy systems due to its unique and advantageous features. Merits of CSI over the more popular Voltage Source Inverter (VSI) topology have been elaborated on by a number of researchers. However, there is a dearth of quality work in modeling and control of CSI topology interfacing renewable energy resources to the grid. To enrich the study focussing on application of CSI for renewable energy interface, this thesis develops a multilevel structure based on CSI for three-phase grid-connected Photovoltaic (PV) application. In the first part of research, a single-stage CSI interfacing to PV array is developed. The CSI-based PV system is equipped with Maximum Power Point Tracker (MPPT), DC-link current controller, and AC-side current controller. To eliminate the nonlinearity introduced by the PV array, a feed-forward control is introduced in the DC-link current controller. The AC-side current controller is responsible for maintaining unity power factor at the Point of Common Coupling (PCC). To verify the performance of the developed CSI-based PV system, a number of simulation studies are carried out in PSCAD/EMTDC environment. To illustrate the performance of the CSI-based PV system during transients on the grid side, simulation studies are carried out for four kinds of faults. Results obtained from fault studies are highly in favor of CSI topology and provide illustrative evidence for short-circuit current protection capability of the CSI. On the other hand, the VSI-based PV system performs poorly when subjected to similar grid transients. To extend the research on CSI-based PV system further, a multilevel structure based on CSI is developed. The multilevel structure is a parallel combination of $n$ CSI units and capable of producing $2n+1$ levels of current at the terminal of the inverter. Each unit in the multilevel structure has its own MPPT, DC-link current controller. However, on the AC-side a combined current controller is proposed. The design results in a high power rating with reduced number of filters, sensors and controllers. The developed multilevel structure can operate with PV arrays exposed to equal and unequal insolation level. However, when the PV arrays are operating under unequal insolation level, low order harmonics are generated in the sinusoidal current that is injected into the grid. Elimination of these harmonics is performed by implementing a modified control strategy in stationary reference frame that corresponds to the harmonic component that needs to be minimized. The modified control strategy operates in coordination with the existing DC-side and AC-side current controllers, and MPPTs. Therefore, real-time suppression of current harmonics can be ensured. Performance of the multilevel structure is verified by different transient studies.

A numerical analysis is performed for the three-dimensional, turbulent flow of air in a thyristor valve hall located at the Dorsey Converter Station, owned and operated by Manitoba Hydro. The goal of this analysis was to determine the configurations that result in increased air-side cooling effectiveness in the valve hall. The governing equations are solved using the Computational Fluid Dynamics (CFD) code CFX-5. This computer code uses a finite volume method of solution and is based on a finite element approach for representing the geometry. The effects of inlet and outlet opening geometry, inlet air mass flow rate, and inlet air angle on the thermal performance for the air-side cooling of the thyristor valve hall geometry are examined.

In this study, a new arranged catalyst support with distinct open pore morphology has been fabricated via thermal oxidation of an FeCrAl alloy with an aim to address mass transfer limitations that conventional supports have due to their internal porosity. Subsequent characterization tests including, drop shape analysis, X-ray diffraction, X-ray photoelectron spectroscopy and scanning electron microscopy revealed that the support formed upon thermal oxidation for 1 hour at 930C, 1 hour at 960C and 2 hours at 990C embodies advantageous support characteristics. Preliminary tests were performed using palladium (active component) deposited on the new support in representative three phase hydrogenation reactions of 2-methyl-3-butyn-2-ol or 2-methyl-3-buten-2-ol. Absence of mass transfer limitations was verified for 2-methyl-3-buten-2-ol hydrogenation at 35-50C, 1200 rpm stirring speed and 0.46 MPa pressure of hydrogen in a 300 ml semi-batch reactor using ethanol as solvent. The study paves the way to the development of arranged catalysts based on FeCrAl alloy fibers for structured reactors. / Chemical Engineering

A large number of studies have concentrated on golf swing biomechanics, ranging from planar rigid-link models to 3D kinematic analysis. A promising technique, instantaneous screw axis (ISA) theory, has not been covered in the literature and could provide a better true segment rotation approximation. The objectives of this study are to identify ISA location and orientation, as well as segment angular velocity, of the major body segments involved in the golf swing. For all subjects, it was found that the magnitude of maximum angular velocities increased from the most proximal segment (the pelvis) to the most distal segment (the left arm), in accordance with the summation of speeds principle. Furthermore, most subjects achieved their maximum angular velocities in the desired kinematic sequence, where the first maxima was achieved by the most proximal segment and followed by the more distal segments in the kinematic chain.

Early detection is one of the most important factors in the survival of patients diagnosed with breast cancer. For this reason the development of improved screening mammography methods is one of primary importance. One problem that is present in standard planar mammography, which is not solved with the introduction of digital mammography, is the possible masking of lesions by normal breast tissue because of the inherent collapse of three-dimensional anatomy into a two-dimensional image. Digital tomosynthesis imaging has the potential to avoid this effect by incorporating into the acquired image information on the vertical position of the features present in the breast. Previous studies have shown that at an approximately equivalent dose, the contrast-detail trends of several tomosynthesis methods are better than those of planar mammography. By optimizing the image acquisition parameters and the tomosynthesis reconstruction algorithm, it is believed that a tomosynthesis imaging system can be developed that provides more information on the presence of lesions while maintaining or reducing the dose to the patient. Before this imaging methodology can be translated to routine clinical use, a series of issues and concerns related to tomosynthesis imaging must be addressed. This work investigates the relevant physical processes to improve our understanding and enable the introduction of this tomographic imaging method to the realm of clinical breast imaging. The processes investigated in this work included the dosimetry involved in tomosynthesis imaging, x-ray scatter in the projection images, imaging system performance, and acquisition geometry. A comprehensive understanding of the glandular dose to the breast during tomosynthesis imaging, as well as the dose distribution to most of the radiosensitive tissues in the body from planar mammography, tomosynthesis and dedicated breast computed tomography was gained. The analysis of the behavior of x-ray scatter in tomosynthesis yielded an in-depth characterization of the variation of this effect in the projection images. Finally, the theoretical modeling of a tomosynthesis imaging system, combined with the other results of this work was used to find the geometrical parameters that maximize the quality of the tomosynthesis reconstruction.

This project explores systematic strategies for establishing a definitive mode of representation in drawing. These strategies are considered in the context of the subjectivities and contingencies of perceptual experience, the mediation of that experience and inherent limitations in representational language. The aim is to explore the possibilities of constructing two-dimensional artworks which serve to define or investigate perceptual processes, perspective devices and spatial relationships.

Thesis (Ph.D.)--Tufts University, 2000. / Adviser: David A. Boas. Submitted to the Dept. of Electrical Engineering and Computer Science. Includes bibliographical references (leaves 139-147). Access restricted to members of the Tufts University community. Also available via the World Wide Web;

Thesis (M.F.A.)--Rochester Institute of Technology, 2007. / Typescript. Includes bibliographical references (leaves 20-21).

Thesis (M.S.)--Worcester Polytechnic Institute. / Keywords: three-dimensional analysis. Includes bibliographical references (leaves 50-51).