Voir fichier joint

The structural performance of Rounded Dovetail Connections (RDC) has been studied experimentally and numerically to provide information needed for connection structural design. RDC are mainly used to transfer vertical shear forces, but test results show that they can carry considerable load in tension and bending. Geometric parameters, such as dovetail flange angle and dovetail height are shown to significantly effect affect the structural performance of RDC. Results show that it is impractical to determine a set of empirical equations to describe the structural performance of RDC based on basic wood material properties. RDC manufactured and tested with low and constant moisture content outperformed those evaluated under other climatic conditions, and test results demonstrate that RDC should be produced at low machine speed and with minimal a gap between the connecting members. RDC in laminated strand lumber have higher capacity and fail under larger deformations compared to RDC in western hemlock. A three-dimensional finite element method model is presented and validated with experimental tests. Good agreement is achieved between the load deformation response predicted by the model and the experimentally observed load deformation response. Therefore the model is deemed suitable for estimating the stresses needed to develop failure criteria. A failure criterion for the analysis of RDC is presented taking into account size effect in the strength of wood. Based on the experimental and numerical studies, a design equation for RDC is presented that provides the engineering community with a new design tool. Finally, self tapping screws as reinforcement have been studied and are shown to significantly improve the structural performance of RDC under vertical shear loading.

The structural performance of Rounded Dovetail Connections (RDC) has been studied experimentally and numerically to provide information needed for connection structural design. RDC are mainly used to transfer vertical shear forces, but test results show that they can carry considerable load in tension and bending. Geometric parameters, such as dovetail flange angle and dovetail height are shown to significantly effect affect the structural performance of RDC. Results show that it is impractical to determine a set of empirical equations to describe the structural performance of RDC based on basic wood material properties. RDC manufactured and tested with low and constant moisture content outperformed those evaluated under other climatic conditions, and test results demonstrate that RDC should be produced at low machine speed and with minimal a gap between the connecting members. RDC in laminated strand lumber have higher capacity and fail under larger deformations compared to RDC in western hemlock. A three-dimensional finite element method model is presented and validated with experimental tests. Good agreement is achieved between the load deformation response predicted by the model and the experimentally observed load deformation response. Therefore the model is deemed suitable for estimating the stresses needed to develop failure criteria. A failure criterion for the analysis of RDC is presented taking into account size effect in the strength of wood. Based on the experimental and numerical studies, a design equation for RDC is presented that provides the engineering community with a new design tool. Finally, self tapping screws as reinforcement have been studied and are shown to significantly improve the structural performance of RDC under vertical shear loading.

The structural performance of Rounded Dovetail Connections (RDC) has been studied experimentally and numerically to provide information needed for connection structural design. RDC are mainly used to transfer vertical shear forces, but test results show that they can carry considerable load in tension and bending. Geometric parameters, such as dovetail flange angle and dovetail height are shown to significantly effect affect the structural performance of RDC. Results show that it is impractical to determine a set of empirical equations to describe the structural performance of RDC based on basic wood material properties. RDC manufactured and tested with low and constant moisture content outperformed those evaluated under other climatic conditions, and test results demonstrate that RDC should be produced at low machine speed and with minimal a gap between the connecting members. RDC in laminated strand lumber have higher capacity and fail under larger deformations compared to RDC in western hemlock. A three-dimensional finite element method model is presented and validated with experimental tests. Good agreement is achieved between the load deformation response predicted by the model and the experimentally observed load deformation response. Therefore the model is deemed suitable for estimating the stresses needed to develop failure criteria. A failure criterion for the analysis of RDC is presented taking into account size effect in the strength of wood. Based on the experimental and numerical studies, a design equation for RDC is presented that provides the engineering community with a new design tool. Finally, self tapping screws as reinforcement have been studied and are shown to significantly improve the structural performance of RDC under vertical shear loading. / Forestry, Faculty of / Graduate

Much previous experimentation related to wood structures has employed monotonic loading to replicate static situations. However, instances of natural hazards have raised interest in the response of structural connections to dynamic loads. This increased interest led the Consortium of Universities for Research in Earthquake Engineering (CUREE) to develop a testing protocol for reverse-cyclic loading, which involves cycling loads through zero in order to test specimens in both tension and compression. With the CUREE testing protocol in place, recent research has been devoted to understanding the effects of reverse-cyclic loading on multiple-fastener connections. Experimentation by Heine (2001), Anderson (2002), Billings (2004) and others contributed to a better understanding of bolted connection behavior under reverse-cyclic loading. However, some questions remained. Billings was unable to consistently produce yield modes III and IV, meaning that her suggested bolt spacing of seven times the bolt diameter (7D) could not be applied to connections subject to these yield modes without further testing. In addition, the work of Anderson and Billings raised questions regarding the proper measurement of bending yield strength in bolts and the relationship between the bending yield strength and the tensile yield strength. These topics are each addressed by this project and thesis report. Results of the connection testing presented in this report can be used in conjunction with the work of Anderson and Billings to critically evaluate the 4D between-bolt spacing recommended by the National Design Specification (NDS) for Wood Construction (AF&PA, 2001). Results of the bolt testing provide a supplement to the search for a reliable method for the measurement of bending yield strength in bolts. / Master of Science

L'assemblage des éléments de structures en bois de dimensions standard comme des poutres massives ou composites s'effectue très fréquemment avec des ancrages métalliques cloués. Ces éléments en tôle pliée formés à froid peuvent être mis sur le marché Européens lorsqu'un ATE est obtenu à partir des recommandations de l'ETAG 015. Le développement ainsi que la caractérisation de la résistance de ces ancrages s'effectue jusqu'à présent dans la société CULLEN Building Products par des essais longs et coûteux. En alternative à cette démarche, ce travail présente une démarche permettant de modéliser le comportement de ces assemblages par la méthode des éléments finis. En premier lieu une étude est conduite sur les types d'aciers utilisés et sur l'influence de la phase de formage sur la résistance de l'ancrage. Il est alors montré qu'il n'est pas nécessaire d'intégrer l'état d'écrouissage produit par le pliage et que la modélisation peut débuter à partir de la géométrie finale à l'aide d'éléments coques. En second lieu une modélisation simplifiée du comportement des pointes est proposée. Les paramètres nécessaires à sa mise en oeuvre sont identifiés. Le modèle est mis en oeuvre pour simuler le comportement d'un assemblage tôle sur bois à une seule pointe. Les résultats sont confrontés à des résultats expérimentaux. La modélisation de l'ancrage étant forcément tridimensionnelle, une modélisation non linéaire du bois 3D est proposée en idéalisant le bois comme une structure. Cette structure est composée de cube de mousse (crushable foam) associé à des poutres élasto plastique qui donne à cet édifice son caractère fortement orthotrope. Ce modèle structurale du bois est mis en oeuvre pour modéliser le cisaillement de barreaux de bois, de la compression transversale sur appuis de poutre, des essais d'enfoncement de broches et un assemblage traditionnel par embrèvement. Ces modélisations permettent de montrer les capacités du modèle à décrire les comportements et de définir ses limites. Dans une dernière partie, l'ancrage, les pointes et le bois sont rassemblés pour constitué trois modèles d'ancrages caractéristiques les plus complexes de la production CULLEN. Les résultats obtenus sont confrontés à des résultats expérimentaux conduits en laboratoire. Enfin les modélisations sont utilisés pour expliquer le comportement interne des ancrages au cours du chargement jusqu'à l'atteinte de la rupture / The assembly of various elements of timber structures of standard dimensions such as timber beams or composite beams is often achieved by nailed steel connectors. These folded steel elements obtained by cold forming can be launched on the European market once an ETA is delivered regarding the recommendations of the ETAG 015. Up to now, the development and the characterisation of the strength of these connectors have been done within the company: CULLEN Building Products by lengthy and costly experimental tests. As an alternative to this procedure, this work presents an approach which enables modelling the behaviour of these connections by the finite element method. In the first place the influence of the type of steel used and the forming process on the strength of these hangers was studied. It is shown that it is not necessary to take into account the hardening produced by the forming of the steel so that the modelling can be achieved from the final geometry by shell elements. Secondly a simplified model of the behaviour of the nails is proposed. The parameters necessary for its implementation are identified. The model is then used to simulate the behaviour of the connection of a steel plate to timber by a single nail. These results are then confronted with the experimental results. As the model is necessarily 3 dimensional, a 3D non linear model is proposed for the timber by considering it as a structure. This structure is composed of cubes of crushable foam which are associated with elasto-plastic beams to give this structure its highly orthotropic behaviour. This structural model of wood is implemented to model the shear of timber bars, transversal compression where beams are supported, embedment tests of steel dowels and a traditional bird's mouth assembly. These various models show the capacities of this structural model to describe timber's complex behaviours; they also define the limits of this modelling. In the last section, the hanger, the nails and the timber are assembled in order to constitute the models for three characteristic and complex hangers of CULLEN's production. The results obtained are confronted with the experimental results. Finally, the models are used to explain the internal behaviour of these hangers at various loads up to their failure

Glued connections are relatively new in structural timber engineering. They are expected to show high connection stiffness as well as a high connection strength compared to mechanical connections e.g. dowel‐type connections.The main aim of this thesis is to characterize the behavior of glued timber connections under pure tension by conducting experiments as well as numerical simulations. Hereby the influence of different parameters is studied such as the geometry (bond-line length and thickness) and the material properties (e.g. adhesives of highly diverse stiffness). Additionally, reference tests on a dowel-type connection are made. The purpose is to see the differences between dowelled and glued connections and to see if there are some advantages in using glued timber connections (the base geometry was chosen acc. to Eurocode 5).Finite element models were created in the software ABAQUS. The models were used to predict the connection stiffness and compare this to the experimental results. In addition, parametric studies were performed on e.g. overlapping lengths. The comparison between experiments and simulations showed good agreement.It was found that glued connections with the adhesives SikaPower-4720 and SikaFast-5215 NT (an epoxy and an acrylate, respectively) had higher stiffness than the dowel connections, whereas connections with the silicone adhesive SikaSil SG-500 had a lower stiffness. A general conclusion drawn from this work is that the glued timber connections simulated in this project should also be suitable for application to complex connections and situations involving other loading situations than pure tension.

This thesis is mainly focused on the seismic behaviour of cross laminated timber (CLT) buildings. The document can be subdivided into three main sections closely related to each other. In the first part, after a short introduction on the state of the art on timber buildings regarding the constructive and legislative issues, the behaviour of CLT buildings is presented. The research is focused on the study on single shear-walls, on the multi-storey single-walls and on the behaviour of the whole buildings. The analyses are performed in order to assess the ductility level achievable by a CLT building as a result of different choices for the ductility of the connections at the foundation level. In order to estimate the ductility level, a large number of non-linear analyses were performed. This was possible thanks to a Matlab code, specifically developed, which allowed to reduce the computational burden. The results are used to evaluate a reliable set of behaviour factors to be applied in the seismic design of CLT buildings. In the second part of thesis, the low-cyclic fatigue strengths for different typologies of dissipative timber connections are presented. The low-cyclic fatigue strength represents a key-parameter in the assessment of the seismic behaviour of timber connections. In fact, high values of ductility associated with low values of strength degradation ensure a remarkable and reliable energy dissipation without a significant loss of strength. Despite the current version of chapter 8 of Eurocode 8 requires specific values of seismic demand for timber connections in terms of low-cyclic fatigue strength, no specific provision is reported to this regard in the European Standard for the cycling testing of timber connections and assemblage in seismic design (EN 12512). In This Standard the ductility capacity and the impairment of strength are calculated as separate mechanical parameters. For this reason, a proposal of revision of European Standard EN12512 is presented and discussed. The third and last part of the thesis describes an innovative connection for CLT buildings. This innovative connection was originally developed in order to absorb both traction and shear actions. Furthermore, a good performance has been obtained in terms of low-cyclic fatigue strength and ductility, with the aim of conceiving a connection able of satisfy the requirements of the current seismic European Standard. The design of this new connection was an iterative process, starting from some simplified numerical models. After some improvements, it was possible to obtain the expected performance levels. The strength and rigidity of the designed connection were initially obtained through numerical analysis, and then compared with the results of physical tests carried out in the Materials and Structures Testing Laboratory (MSTL), that is a part of the Department of Civil, Environmental and Mechanical Engineering (DICAM) of the University of Trento.

For structural engineers, the two most important design criteria are utility andsafety. It is about making sure that a structural component is reliable enough not toendanger any of a building's users, while at the same time being as sustainable andefficiently designed as possible. In other words, an element must be safe enough towithstand the improbability and sufficiently cheap to be relevant for the design.Considering this, using a material such as wood instead of metal may prove to be asustainable alternative for certain building components.Timber can be designed to sustain high temperatures and fire; it has a high strengthrelative to its weight and is naturally produced. Furthermore, an engineered woodproduct such as birch plywood has proven very strong in structural applications,especially when glued. Therefore, birch plywood has great potential as a reliablematerial in structural components. In this work, a total of 24 specimens with birchplywood connections were tested experimentally.The specimens were designed to enforce stress states that would occur in actualtrusses. Additionally, Specimens were assembled with two different connectionmethods, one being a dowel-type connection and the other being a glued-type. Eachtype of connection was tested in both tension and compression, with a total of threerepetitions each. For the glued-type specimens, birch plywood plates wereinvestigated in three different angles to the face grain; 0°, 5° and 15°. Theload-displacement relationships and the failure modes are of specific interest in thisthesis.Test results showed that failure modes were semi-brittle and distinct, and the testsshowed that glued-type connections withstood 37% higher loads than dowelledtypes. Specimens might withstand even higher loads if gluing were performed in amore controlled environment. The load-to-face-grain angle of plywood also had asignificant impact on the capacity of connections. For the 0°-specimens with gluedconnections tested in compression, no failures occurred in the plywood, and testsreached loads as high as 82 kN. Calculations were made estimating the load capacityas high as 95 kN, but possibly a more realistic approximation would be 85 kN. Thiswould imply that the 0°-specimens are around 20% stronger than the 15°-specimensand approximately 17,7% stronger than the 5°-specimens tested in compression.Birch plywood is promising to be used in connections of timber structures whereplates transfer forces between structural elements.

Damages during extreme wind events highlight the weaknesses of mechanical fasteners at the roof-to-wall connections in residential timber frame buildings. The allowable capacity of the metal fasteners is based on results of unidirectional component testing that do not simulate realistic tri-axial aerodynamic loading effects. The first objective of this research was to simulate hurricane effects and study hurricane-structure interaction at full-scale, facilitating better understanding of the combined impacts of wind, rain, and debris on inter-component connections at spatial and temporal scales. The second objective was to evaluate the performance of a non-intrusive roof-to-wall connection system using fiber reinforced polymer (FRP) materials and compare its load capacity to the capacity of an existing metal fastener under simulated aerodynamic loads. The Wall of Wind (WoW) testing performed using FRP connections on a one-story gable-roof timber structure instrumented with a variety of sensors, was used to create a database on aerodynamic and aero-hydrodynamic loading on roof-to-wall connections tested under several parameters: angles of attack, wind-turbulence content, internal pressure conditions, with and without effects of rain. Based on the aerodynamic loading results obtained from WoW tests, sets of three force components (tri-axial mean loads) were combined into a series of resultant mean forces, which were used to test the FRP and metal connections in the structures laboratory up to failure. A new component testing system and test protocol were developed for testing fasteners under simulated tri-axial loading as opposed to uni-axial loading. The tri-axial and uni-axial test results were compared for hurricane clips. Also, comparison was made between tri-axial load capacity of FRP and metal connections. The research findings demonstrate that the FRP connection is a viable option for use in timber roof-to-wall connection system. Findings also confirm that current testing methods of mechanical fasteners tend to overestimate the actual load capacities of a connector. Additionally, the research also contributes to the development a new testing protocol for fasteners using tri-axial simultaneous loads based on the aerodynamic database obtained from the WoW testing.