Les océans subissent des pressions d'origine anthropique particulièrement fortes comme la surpêche, la pollution physico-chimique, et le bruit rayonné par les activités industrielles et militaires. Cette thèse se place dans un contexte de compréhension de l'impact du bruit rayonné dans les océans sur les mammifères marins. L'acoustique passive joue donc un rôle fondamental dans ce problème. Ce travail aborde la tâche de détection de signatures acoustiques de mammifères marins dans le spectrogramme. Cette tâche est difficile pour deux raisons : 1. le bruit océanique a une structure complexe (non-stationnaire, coloré), 2. les signaux de mammifères marins sont inconnus et possèdent eux aussi une structure complexe (non-stationnaires bande étroite et/ou impulsionnels). Le problème doit donc être résolu de manière locale en temps-fréquence, et ne pas faire d'hypothèse a priori sur le signal. Des détecteurs statistiques basés uniquement sur la connaissance des statistiques du bruit dans le spectrogramme existent, mais souffrent deux lacunes : 1. leurs performances en terme de probabilité de fausse alarme/ probabilité de détection se dégradent fortement à faible rapport signal à bruit, et 2. ils ne sont pas capables de séparer les signaux à bande étroite des signaux impulsionnels. Ce travail apporte des pistes de réflexion sur ces problèmes.L'originalité de ce travail de thèse repose dans la formulation d'un test d'hypothèse binaire prenant explicitement en compte l'organisation spatiale des pics temps-fréquence. Nous introduisons une méthode d'Analyse de la Densité des Fausses Alarmes (FADA) qui permet de discriminer les régions temps-fréquence abritant le signal de celles n'abritant que du bruit. Plus précisément,le nombre de fausses alarmes dans une région du plan est d'abord modélisé par une loi binomiale, puis par une loi binomiale corrélée, afin de prendre en considération la redondance du spectrogramme. Le test d'hypothèse binaire est résolu par une approche de Neyman-Pearson. Nous démontrons numériquement la pertinence de cette approche et nous la validons sur données réelles de mammifères marins disposant d'une grande variété de signaux et de conditions de bruit. En particulier, nous illustrons la capacité de FADA à discriminer efficacement le signal du bruit en milieu fortement impulsionnel. / The oceans experience heavy anthropogenic pressure due to overfishing, physico-chemical pollution, and noise radiated by industrial and military activities. This work focuses on the use of passive acoustic monitoring of the oceans, as a tool to understand the impact of radiated noise on marine ecosystems, and particularly on marine mammals. This work tackles the task of detection of acoustical signals of marine mammals using the spectrogram. This task is uneasy for two reasons : 1. the ocean noise structure is complex (non-stationary and colored) and 2. the signals of interest are unknown and also shows a complex structure (non-stationary narrow band and/or impulsive). The problem therefore must be solved locally without making a priori hypothesis on the signal. Statistical detectors only based on the local analysis of the noise spectrogram coefficients are available, making them suitable for this problem. However, these detectors suffer two disadvantages : 1. the trade-offs false alarm probability/ detection probability that are available for low signal tonoise ratio are not satisfactory and 2. the separation between narrow-band and impulsive signals is not possible. This work brings some answers to these problems.The main contribution of this work is to formulate a binary hypothesis test taking explicitly in account the spatial organization of time-frequency peaks. We introduce the False Alarm Density Analysis (FADA) framework that efficiently discriminates time-frequency regions hosting signal from the ones hosting noise only. In particular the number of false alarms in regions of the binary spectrogram is first modeled by a binomial distribution, and then by a correlated binomial distribution to take in account the spectrogram redundancy. The binary hypothesis test is solved using a Neyman-Pearson criterion.We demonstrate the relevance of this approach on simulated data and validate the FADA detector on a wide variety of real signals. In particular we show the capability of the proposed method to efficiently detect signals in highly impulsive environment.

Submitted by Renata Lopes (renatasil82@gmail.com) on 2016-02-16T09:52:46Z No. of bitstreams: 1 alamsilvamenezes.pdf: 8301590 bytes, checksum: aed618e30f38206da4bf4f329924f87e (MD5) / Approved for entry into archive by Adriana Oliveira (adriana.oliveira@ufjf.edu.br) on 2016-02-26T12:30:53Z (GMT) No. of bitstreams: 1 alamsilvamenezes.pdf: 8301590 bytes, checksum: aed618e30f38206da4bf4f329924f87e (MD5) / Made available in DSpace on 2016-02-26T12:30:53Z (GMT). No. of bitstreams: 1 alamsilvamenezes.pdf: 8301590 bytes, checksum: aed618e30f38206da4bf4f329924f87e (MD5) Previous issue date: 2014-09-01 / A presente tese propõe soluções ao problema da explicitação do conteúdo espectral de processos estacionários e não estacionários, com aplicações na estimação de frequência, estimação da densidade espectral de potência e no monitoramento do espectro. A técnica de estimação de frequência proposta nesta tese, baseada na warped discrete Fourier transform, apresenta, de acordo com as simulações computacionais, o melhor desempenho frente às demais técnicas comparadas, atingindo o Cramer-Rao bound para uma ampla faixa de relação sinal ruído. Em relação a estimação da densidade espectral de potência, a Hartley Multitaper method, proposta nesta tese, apresenta desempenho similar à multitaper method, em termos da variância de estimação e da polarização do espectro, mas simpli cação de implementação. Uma técnica para monitoramento do espectro para sistemas power line communication é proposta, levando em consideração o conceito de quanta e a diversidade observada quando os sinais são aquisitados a partir da rede de energia elétrica e do ar. Baseando-se em sinais sintéticos, gerados em computador, assim como dados de medição do espectro, obtidos utilizando uma antena e o cabo de energia elétrica como elementos sensores, veri fica-se que o desempenho da técnica proposta supera a monitoração padrão, sobretudo quando a diversidade gerada pelo cabo e pela antena sobre o sinal monitorado é explorada na detecção. / This dissertation aims at discussing solutions to deal with spectral analysis of stationary and non-stationary processes for frequency estimation, power spectral density estimation and spectral monitoring applications. The frequency estimation techniques are assessed through computer simulations. The proposed technique for frequency estimation is based on warped discrete Fourier transform outperforms other techniques, achieving the Cramer-Rao Bound for a wide range of signal to noise ratio. Regarding the power spectral density estimation, the proposed Hartley Multitaper Method shows similar performance, in terms of variance of estimates and polarization spectrum; however, it can simplify the implementation complexity. The introduced spectrum sensing technique is based on quanta de nition and the diversity o ered by the signals acquired from the electric power grids and the air. Based on computer-generation data and those one obtained during a measurement campaign, which one in this thesis is evaluated using synthetic signals, generated by computer, as well as measurement data of the spectrum. The numerical results show that the proposed technique outperforms a previous technique and can attain the very detection ratio and the very low false alarm when the diversity yielded by electric power grid and air is exploited.

The aim of the dissertation was to design a realistic, low-complexity non-binary (NB) low density parity check (LDPC) coded space-time-frequency (STF) coded multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) system with an iterative joint decoder and detector structure at the receiver. The goal of the first part of the dissertation was to compare the performance of different design procedures for NB-LDPC codes on an additive white Gaussian noise (AWGN) channel, taking into account the constraint on the code length. The effect of quantisation on the performance of the code was also analysed. Different methods for choosing the NB elements in the parity check matrix were compared. For the STF coding, a class of universal STF codes was used. These codes use linear pre-coding and a layering approach based on Diophantine numbers to achieve full diversity and a transmission rate (in symbols per channel use per frequency) equal to the number of transmitter antennas. The study of the system considers a comparative performance analysis of di erent ST, SF and STF codes. The simulations of the system were performed on a triply selective block fading channel. Thus, there was selectivity in the fading over time, space and frequency. The effect of quantisation at the receiver on the achievable diversity of linearly pre-coded systems (such as the STF codes used) was mathematically derived and verified with simulations. A sphere decoder (SD) was used as a MIMO detector. The standard method used to create a soft-input soft output (SISO) SD uses a hard-to-soft process and the max-log-map approximation. A new approach was developed which combines a Hopfield network with the SD. This SD-Hopfield detector was connected with the fast Fourier transform belief propagation (FFT-BP) algorithm in an iterative structure. This iterative system was able to achieve the same bit error rate (BER) performance as the original SISO-SD at a reduced complexity. The use of the iterative Hopfield-SD and FFT-BP decoder system also allows performance to be traded off for complexity by varying the number of decoding iterations. The complete system employs a NB-LDPC code concatenated with an STF code at the transmitter with a SISO-SD and FFT-BP decoder connected in an iterative structure at the receiver. The system was analysed in varying channel conditions taking into account the effect of correlation and quantisation. The performance of different SF and STF codes were compared and analysed in the system. An analysis comparing different numbers of FFT-BP and outer iterations was also done. AFRIKAANS : Die doel van die verhandeling was om ’n realistiese, lae-kompleksiteit nie-binˆere (NB) LDPC gekodeerde ruimte-tyd-frekwensie-gekodeerde MIMO-OFDM-sisteem met iteratiewe gesamentlike dekodeerder- en detektorstrukture by die ontvanger te ontwerp. Die eerstem deel van die verhandeling was om die werkverrigting van verskillende ontwerpprosedures vir NB-LDPC kodes op ’n gesommeerde wit Gausruiskanaal te vergelyk met inagneming van die beperking op die lengte van die kode. Verskillende metodes om die nie-bineêre elemente in die pariteitstoetsmatriks te kies, is gebruik. Vir die ruimte-tyd-frekwensiekodering is ’n klas universele ruimte-tyd-frekwensiekodes gebruik. Hierdie kodes gebruik lineêre pre-kodering en ’n laagbenadering gebaseer op Diofantiese syfers om volle diversiteit te bereik en ’n oordragtempo (in simbole per kanaalgebruik per frekwensie) gelyk aan die aantal senderantennes. Die studie van die sisteem oorweeg ’n vergelykende werkverrigtinganalisie van verskillende ruimte-tyd-, ruimte-freksensie- en ruimte-tyd-frekwensiekodes. Die simulasies van die sisteem is gedoen op ’n drievoudig selektiewe blokwegsterwingskanaal. Daar was dus selektiwiteit in die wegsterwing oor tyd, ruimte en frekwensie. Die effek van kwantisering by die ontvanger op die bereikbare diversiteit van lineêr pre-gekodeerde sisteme (soos die ruimte-tyd-frekwensiekodes wat gebruik is) is matematies afgelei en bevestig deur simulasies. ’n Sfeerdekodeerder (SD) is gebruik as ’n MIMO-detektor. Die standaardmetode wat gebuik is om ’n sagte-inset-sagte-uitset (SISO) SD te skep, gebruik ’n harde-na-sagte proses en die maksimum logaritmiese afbeelding-benadering. ’n Nuwe benadering wat ’n Hopfield-netwerk met die SD kombineer, is ontwikkel. Hierdie SD-Hopfield-detektor is verbind met die FFT-BP-algoritme in iteratiewe strukture. Hierdie iteratiewe sisteem was in staat om dieselfde bisfouttempo te bereik as die oorspronklike SISO-SD, met laer kompleksiteit. Die gebruik van die iteratiewe Hopfield-SD en FFT-BP-dekodeerdersisteem maak ook daarvoor voorsiening dat werkverrigting opgeweeg kan word teen kompleksiteit deur die aantal dekodering-iterasies te varieer. Die volledige sisteem maak gebruik van ’n QC-NB-LDPC-kode wat met ’n ruimte-tyd-frekwensiekode by die sender aaneengeskakel is met ’n SISO-SD en FFT-BP-dekodeerder wat in ’n iteratiewe struktuur by die ontvanger gekoppel is. Die sisteem is onder ’n verskeidenheid kanaalkondisies ge-analiseer met inagneming van die effek van korrelasie en kwantisering. Die werkverrigting van verskillende ruimte-frekwensie- en ruimte-tyd-frekwensiekodes is vergelyk en in die sisteem ge-analiseer. ’n Analise om ’n wisselende aantal FFT-BP en buite-iterasies te vergelyk, is ook gedoen. Copyright / Dissertation (MEng)--University of Pretoria, 2010. / Electrical, Electronic and Computer Engineering / unrestricted

Aerospace structures comprising of metals and composites are exposed to extreme loading and environmental conditions which necessitates regular inspection and maintenance to verify and monitor overall structural integrity. The timely and accurate detection, characterization and monitoring of structural cracking, corrosion, delaminating, material degradation and other types of damage are of major concern in the operational environment. Along with these, stringent requirements of safety and operational reliability have lead to evolutionary methods for evaluation of structural integrity. As a result, conventional nondestructive evaluation methods have moved towards a new concept, Structural Health Monitoring (SHM). SHM provides in-situ information a bout the occurrence of damage if any, location and severity of damage and residual life of the structure and also helps in improving the safety, reliability and confidence levels of critical engineering structures. While the concepts underlying SHM are well understood, development of methods is still in a nascent stage which requires extensive research that is challenging and has been the main motivating factor for undertaking the work reported in the thesis. Under the scope of the investigations carried out in this thesis, an integrated approach using Ultrasonic (active) and Acoustic Emission (passive) methods has been explored for SHM of metallic and composite plate structures using a distributed array of surface bonded circular piezoelectric wafer active sensors(PWAS). In ultrasonic method, PWAS is used for actuation and reception of Lamb waves in plate structures. The damage detection is based on the interaction of waves with defects resulting in reflection, mode conversion and scattering. In acoustic emission (AE) technique, the same sensor is used to pick up the stress waves generated by initiation or growth of defects or damage. Thus, both the active and passive damage detection methods are used in this work for detection, location and characterization of defects and damage in metallic and composite plates with complex geometries and structural discontinuities. And, thus the strategy adopted is to use time-frequency analysis and time reversal technique to extract the information from Lamb wave signals for damage detection and a geodesic based Lamb wave approach for location of the damage in the structure. To start with experiments were conducted on aluminum plates to study the interaction of Lamb waves with cracks oriented at different angles and on a titanium turbine blade of complex geometry with a fine surface crack. Further, the interaction of Lamb wave modes with multiple layer delaminations in glass fiber epoxy composite laminates was studied. The data acquired from these experiments yielded complex sets of signals which were not easily discern able for obtaining the information required regarding the defects and damage. So, to obtain a basic understanding of the wave patterns, Spectral finite element method has been employed for simulation of wave propagation in composite beams with damages like delamination and material degradation. Following this, time-frequency analysis of a number of simulated and experimental signals due to elastic wave scattering from defects and damage were performed using wavelet transform (WT) and Hilbert-Huang transform(HHT).And, a comparison of their performances in the context of quantifying the damages has given detailed insight into the problem of identifying localized damages, dispersion of multi-frequency non-stationary signals after their interaction with different types of defects and damage, finally leading to quantification. Conventional Lamb wave based damage detection methods look for the presence of defects and damage in a structure by comparing the signal obtained with the baseline signal acquired under healthy conditions. The environmental conditions like change in temperature can alter the Lamb wave signals and when compared with baseline signals may lead to false damage prediction. So, in order to make Lamb wave based damage detection baseline free, in the present work, the time reversal technique has been utilized. And, experiments were conducted on metallic and composite plates to study the time reversal behavior ofA0 andS0Lamb wave modes. Damage in the form of a notch was introduced in an aluminum plate to study the changes in the characteristics of the time reversed Lamb wave modes experimentally. This experimental study showed that there is no change in the shape of the time reversed Lamb wave in the presence of defect implying no breakage of time reversibility. Time reversal experiments were further carried out on a carbon/epoxy composite T-pull specimen representing a typical structure. And, the specimen was subjected to a tensile loading in a Universal testing machine. PWAS sensor measurements were carried out at no load as also during different stages of delamination due to tensile loading. Application of time reversed A 0 and S0 modes for both healthy and delaminated specimens and studying the change in shape of the time reversed Lamb wave signals has resulted in successful detection of the presence of delamination. The aim of this study has been to show the effectiveness of Lamb wave time reversal technique for damage detection in health monitoring applications. The next step in SHM is to identify the damage location after the confirmation of presence of damage in the structure. Wave based acoustic damage detection methods (UT and AE) employing triangulation technique are not suitable for locating damage in a structure which has complicated geometry and contains structural discontinuities. And, the problem further gets compounded if the material of the structure is anisotropic warranting complex analytical velocity models. In this work, a novel geodesic approach using Lamb waves is proposed to locate the AE source/damage in plate like structures. The approach is based on the fact that the wave takes minimum energy path to travel from the source to any other point in the connected domain. The geodesics are computed numerically on the meshed surface of the structure using Dijkstra’s algorithm. By propagating the waves in reverse virtually from these sensors along the geodesic path and by locating the first inter section point of these waves, one can get the AE source/damage location. Experiments have been conducted on metallic and composite plate specimens of simple and complex geometry to validate this approach. And, the results obtained using this approach has demonstrated the advantages for a practicable source location solution with arbitrary surfaces containing finite discontinuities. The drawback of Dijkstra’s algorithm is that the geodesics are allowed to travel along the edges of the triangular mesh and not inside them. To overcome this limitation, the simpler Dijkstra’s algorithm has been replaced by a Fast Marching Method (FMM) which allows geodesic path to travel inside the triangular domain. The results obtained using FMM showed that one can accurately compute the geodesic path taken by the elastic waves in composite plates from the AE source/damage to the sensor array, thus obtaining a more accurate damage location. Finally, a new triangulation technique based on geodesic concept is proposed to locate damage in metallic and composite plates. The performances of triangulaton technique are then compared with the geodesic approach in terms of damage location results and their suitability to health monitoring applications is studied.

La syncope est une perte brusque de conscience. Bien qu'elle ne soit pas généralement mortelle, elle présente un impact économique sur le système de soins et sur la vie personnelle de personnes en souffrant. L'objet de la présente étude est de réduire la durée du test clinique (environ 1 heure) et d'éviter aux patients de développer une syncope en la prédisant. L'ensemble de travail s'inscrit dans une démarche de datamining associant l'extraction de paramètres, la sélection des variables et la classification. Trois approches complémentaires sont proposées, la première exploite des méthodes d'analyse non-linéaires de séries temporelles extraites de signaux acquises pendant le test, la seconde s'intéresse aux relations cardiovasculaires en proposant des indices dans le plan temps-fréquence et la troisième, plus originale, prendre en compte leurs dynamiques temporelles. / Syncope is a sudden loss of consciousness. Although it is not usually fatal, it has an economic impact on the health care system and the personal lives of people suffering. The purpose of this study is to reduce the duration of the clinical test (approximately 1 hour) and to avoid patients to develop syncope by early predicting the occurrence of syncope. The entire work fits into a data mining approach involving the feature extraction, feature selection and classification. 3 complementary approaches are proposed, the first one exploits nonlinear analysis methods of time series extracted from signals acquired during the test, the second one focuses on time- frequency (TF) relation between signals and suggests new indexes and the third one, the most original, takes into account their temporal dynamics.

Ce manuscrit porte sur la modélisation et l'estimation de certaines non-stationnarités dans les signaux audio. Nous nous intéressons particulièrement à une classe de modèles de sons que nous nommons timbre*dynamique dans lesquels un signal stationnaire, associé au phénomène physique à l'origine du son, est déformé au cours du temps par un opérateur linéaire unitaire, appelé opérateur de déformation, associé à l'évolution temporelle des caractéristiques de ce phénomène physique. Les signaux audio sont modélisés comme des processus gaussiens généralisés et nous donnons dans un premier temps un ensemble d'outils mathématiques qui étendent certaines notions utilisées en traitement du signal au cas des processus stochastiques généralisés.Nous introduisons ensuite les opérateurs de déformations étudiés dans ce manuscrit. L'opérateur de modulation fréquentielle qui est l'opérateur de multiplication par une fonction à valeurs complexes de module unité, et l'opérateur de changement d'horloge qui est la version unitaire de l'opérateur de composition.Lorsque ces opérateurs agissent sur des processus stationnaires les processus déformés possèdent localement des propriétés de stationnarité et les opérateurs de déformation peuvent être approximés par des opérateurs de translation dans les plans temps-fréquence et temps-échelle. Nous donnons alors des bornes pour les erreurs d'approximation correspondantes. Nous développons ensuite un estimateur de maximum de vraisemblance approché des fonctions de dilatation et de modulation. L'algorithme proposé est testé et validé sur des signaux synthétiques et des sons naurels. / This manuscript deals with the modeling and estimation of certain non-stationarities in audio signals. We are particularly interested in a sound class models which we call dynamic*timbre in which a stationary signal, associated with the physical phenomenon causing the sound, is deformed over time by a linear unitary operator, called deformation operator, associated with the temporal evolution of the characteristics of this physical phenomenon.Audio signals are modeled as generalized Gaussian processes. We give first a set of mathematical tools that extend some classical notions used in signal processing in case of generalized stochastic processes.We then introduce the two deformations operators studied in this manuscript. The frequency modulation operator is the multiplication operator by a complex-valued function of unit module and the time-warping operator is the unit version of the composition operator by a bijective function.When these operators act on generalized stationary processes, deformed process are non-stationary generalized process which locally have stationarity properties and deformation operators can be approximated by translation operators in the time-frequency plans and time-scale.We give accurate versions of these approximations, as well as bounds for the corresponding approximation errors.Based on these approximations, we develop an approximated maximum likelihood estimator of the warping and modulation functions. The proposed algorithm is tested and validated on synthetic signals. Its application to natural sounds confirm the validity of the timbre*dynamic model in this context.

[EN] Next-generation terrestrial broadcasting targets at enhancing spectral efficiency to overcome the challenges derived from the spectrum shortage as a result of the progressive allocation of frequencies - the so-called Digital Dividend - to satisfy the growing demands for wireless broadband capacity. Advances in both transmission standards and video coding are paramount to enable the progressive roll-out of high video quality services such as HDTV (High Definition Televison) or Ultra HDTV. The transition to the second generation European terrestrial standard DVB-T2 and the introduction of MPEG-4/AVC video coding already enables the transmission of 4-5 HDTV services per RF (Radio Frequency) channel. However, the impossibility to allocate higher bit-rate within the remaining spectrum could jeopardize the evolution of the DTT platforms in favour of other high-capacity systems such as the satellite or cable distribution platforms. Next steps are focused on the deployment of the recently released High Efficiency Video Coding (HEVC) standard, which provides more than 50% coding gain with respect to AVC, with the next-generation terrestrial standards. This could ensure the competitiveness of the DTT. This dissertation addresses the use of multi-RF channel aggregation technologies to increase the spectral efficiency of future DTT networks. The core of the Thesis are two technologies: Time Frequency Slicing (TFS) and Channel Bonding (CB). TFS and CB consist in the transmission of the data of a TV service across multiple RF channels instead of using a single channel. CB spreads data of a service over multiple classical RF channels (RF-Mux). TFS spreads the data by time-slicing (slot-by-slot) across multiple RF channels which are sequentially recovered at the receiver by frequency hopping. Transmissions using these features can benefit from capacity and coverage gains. The first one comes from a more efficient statistical multiplexing (StatMux) for Variable Bit Rate (VBR) services due to a StatMux pool over a higher number of services. Furthermore, CB allows increasing service data rate with the number of bonded RF channels and also advantages when combined with SVC (Scalable Video Coding). The coverage gain comes from the increased RF performance due to the reception of the data of a service from different RF channels rather that a single one that could be, eventually, degraded. Robustness against interferences is also improved since the received signal does not depend on a unique potentially interfered RF channel. TFS was firstly introduced as an informative annex in DVB-T2 (not normative) and adopted in DVB-NGH (Next Generation Handheld). TFS and CB are proposed for inclusion in ATSC 3.0. However, they have never been implemented. The investigations carried out in this dissertation employ an information-theoretical approach to obtain their upper bounds, physical layer simulations to evaluate the performance in real systems and the analysis of field measurements that approach realistic conditions of the network deployments. The analysis report coverage gains about 4-5 dB with 4 RF channels and high capacity gains already with 2 RF channels. This dissertation also focuses on implementation aspects. Channel bonding receivers require one tuner per bonded RF channel. The implementation of TFS with a single tuner demands the fulfilment of several timing requirements. However, the use of just two tuners would still allow for a good performance with a cost-effective implementation by the reuse of existing chipsets or the sharing of existing architectures with dual tuner operation such as MIMO (Multiple Input Multiple Output). / [ES] La televisión digital terrestre (TDT) de última generación está orientada a una necesaria mejora de la eficiencia espectral con el fin de abordar los desafíos derivados de la escasez de espectro como resultado de la progresiva asignación de frecuencias - el llamado Dividendo Digital - para satisfacer la creciente demanda de capacidad para la banda ancha inalámbrica. Los avances tanto en los estándares de transmisión como de codificación de vídeo son de suma importancia para la progresiva puesta en marcha de servicios de alta calidad como la televisión de Ultra AD (Alta Definición). La transición al estándar europeo de segunda generación DVB-T2 y la introducción de la codificación de vídeo MPEG-4 / AVC ya permite la transmisión de 4-5 servicios de televisión de AD por canal RF (Radiofrecuencia). Sin embargo, la imposibilidad de asignar una mayor tasa de bit sobre el espectro restante podría poner en peligro la evolución de las plataformas de TDT en favor de otros sistemas de alta capacidad tales como el satélite o las distribuidoras de cable. El siguiente paso se centra en el despliegue del reciente estándar HEVC (High Efficiency Video Coding), que ofrece un 50% de ganancia de codificación con respecto a AVC, junto con los estándares terrestres de próxima generación, lo que podría garantizar la competitividad de la TDT en un futuro cercano. Esta tesis aborda el uso de tecnologías de agregación de canales RF que permitan incrementar la eficiencia espectral de las futuras redes. La tesis se centra en torno a dos tecnologías: Time Frequency Slicing (TFS) y Channel Bonding (CB). TFS y CB consisten en la transmisión de los datos de un servicio de televisión a través de múltiples canales RF en lugar de utilizar un solo canal. CB difunde los datos de un servicio a través de varios canales RF convencionales formando un RF-Mux. TFS difunde los datos a través de ranuras temporales en diferentes canales RF. Los datos son recuperados de forma secuencial en el receptor mediante saltos en frecuencia. La implementación de estas técnicas permite obtener ganancias en capacidad y cobertura. La primera de ellas proviene de una multiplexación estadística (StatMux) de servicios de tasa variable (VBR) más eficiente. Además, CB permite aumentar la tasa de pico de un servicio de forma proporcional al número de canales así como ventajas al combinarla con codificación de vídeo escalable. La ganancia en cobertura proviene de un mejor rendimiento RF debido a la recepción de los datos de un servicio desde diferentes canales en lugar uno sólo que podría estar degradado. Del mismo modo, es posible obtener una mayor robustez frente a interferencias ya que la recepción o no de un servicio no depende de si el canal que lo alberga está o no interferido. TFS fue introducido en primer lugar como un anexo informativo en DVB-T2 (no normativo) y posteriormente fue adoptado en DVB-NGH (Next Generation Handheld). TFS y CB han sido propuestos para su inclusión en ATSC 3.0. Aún así, nunca han sido implementados. Las investigaciones llevadas a cabo en esta Tesis emplean diversos enfoques basados en teoría de la información para obtener los límites de ganancia, en simulaciones de capa física para evaluar el rendimiento en sistemas reales y en el análisis de medidas de campo. Estos estudios reportan ganancias en cobertura en torno a 4-5 dB con 4 canales e importantes ganancias en capacidad aún con sólo 2 canales RF. Esta tesis también se centra en los aspectos de implementación. Los receptores para CB requieren un sintonizador por canal RF agregado. La implementación de TFS con un solo sintonizador exige el cumplimiento de varios requisito temporales. Sin embargo, el uso de dos sintonizadores permitiría un buen rendimiento con una implementación más rentable con la reutilización de los actuales chips o su introducción junto con las arquitecturas existentes que operan con un doble sintonizador tales como / [CAT] La televisió digital terrestre (TDT) d'última generació està orientada a una necessària millora de l'eficiència espectral a fi d'abordar els desafiaments derivats de l'escassetat d'espectre com a resultat de la progressiva assignació de freqüències - l'anomenat Dividend Digital - per a satisfer la creixent demanda de capacitat per a la banda ampla sense fil. Els avanços tant en els estàndards de transmissió com de codificació de vídeo són de la màxima importància per a la progressiva posada en marxa de serveis d'alta qualitat com la televisió d'Ultra AD (Alta Definició). La transició a l'estàndard europeu de segona generació DVB-T2 i la introducció de la codificació de vídeo MPEG-4/AVC ja permet la transmissió de 4-5 serveis de televisió d'AD per canal RF (Radiofreqüència). No obstant això, la impossibilitat d'assignar una major taxa de bit sobre l'espectre restant podria posar en perill l'evolució de les plataformes de TDT en favor d'altres sistemes d'alta capacitat com ara el satèl·lit o les distribuïdores de cable. El següent pas se centra en el desplegament del recent estàndard HEVC (High Efficiency Vídeo Coding), que oferix un 50% de guany de codificació respecte a AVC, junt amb els estàndards terrestres de pròxima generació, la qual cosa podria garantir la competitivitat de la TDT en un futur pròxim. Aquesta tesi aborda l'ús de tecnologies d'agregació de canals RF que permeten incrementar l'eficiència espectral de les futures xarxes. La tesi se centra entorn de dues tecnologies: Time Frequency Slicing (TFS) i Channel Bonding (CB). TFS i CB consistixen en la transmissió de les dades d'un servei de televisió a través de múltiples canals RF en compte d'utilitzar un sol canal. CB difon les dades d'un servei a través d'uns quants canals RF convencionals formant un RF-Mux. TFS difon les dades a través de ranures temporals en diferents canals RF. Les dades són recuperades de forma seqüencial en el receptor per mitjà de salts en freqüència. La implementació d'aquestes tècniques permet obtindre guanys en capacitat i cobertura. La primera d'elles prové d'una multiplexació estadística (StatMux) de serveis de taxa variable (VBR) més eficient. A més, CB permet augmentar la taxa de pic d'un servei de forma proporcional al nombre de canals així com avantatges al combinar-la amb codificació de vídeo escalable. El guany en cobertura prové d'un millor rendiment RF a causa de la recepció de les dades d'un servei des de diferents canals en lloc de només un que podria estar degradat. De la mateixa manera, és possible obtindre una major robustesa enfront d'interferències ja que la recepció o no d'un servei no depén de si el canal que l'allotja està o no interferit. TFS va ser introduït en primer lloc com un annex informatiu en DVB-T2 (no normatiu) i posteriorment va ser adoptat en DVB-NGH (Next Generation Handheld). TFS i CB han sigut proposades per a la seva inclusió en ATSC 3.0. Encara així, mai han sigut implementades. Les investigacions dutes a terme en esta Tesi empren diverses vessants basades en teoria de la informació per a obtindre els límits de guany, en simulacions de capa física per a avaluar el rendiment en sistemes reals i en l'anàlisi de mesures de camp. Aquestos estudis reporten guanys en cobertura entorn als 4-5 dB amb 4 canals i importants guanys en capacitat encara amb només 2 canals RF. Esta tesi també se centra en els aspectes d'implementació. Els receptors per a CB requerixen un sintonitzador per canal RF agregat. La implementació de TFS amb un sol sintonitzador exigix el compliment de diversos requisit temporals. No obstant això, l'ús de dos sintonitzadors permetria un bon rendiment amb una implementació més rendible amb la reutilització dels actuals xips o la seua introducció junt amb les arquitectures existents que operen amb un doble sintonitzador com ara MIMO (Multiple Input Multiple Output). / Giménez Gandia, JJ. (2015). Improved Spectrum Usage with Multi-RF Channel Aggregation Technologies for the Next-Generation Terrestrial Broadcasting [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/52520 / TESIS

Desde comienzos del siglo XXI, los sistemas de radiodifusión terrestre han sido culpados de un uso ineficiente del espectro asignado. Para aumentar la eficiencia espectral, los organismos de estandarización de TV digital comenzaron a desarrollar la evolución técnica de los sistemas de TDT de primera generación. Entre otros, uno de los objetivos principales de los sistemas de TDT de próxima generación (DVB-T2 y ATSC 3.0) es proporcionar simultáneamente servicios de TV a dispositivos móviles y fijos. El principal inconveniente de esta entrega simultánea son los diferentes requisitos de cada condición de recepción. Para abordar estas limitaciones, se han considerado diferentes técnicas de multiplexación. Mientras que DVB-T2 acomete la entrega simultánea de los dos servicios mediante TDM, ATSC 3.0 adoptó la Multiplexación por División en Capas (LDM). LDM puede superar a TDM y a FDM al aprovechar la relación de Protección de Error Desigual (UEP), ya que ambos servicios, llamados capas, utilizan todos los recursos de frecuencia y tiempo con diferentes niveles de potencia. En el lado del receptor, se distinguen dos implementaciones, de acuerdo con la capa a decodificar. Los receptores móviles solo están destinados a obtener la capa superior, conocida como Core Layer (CL). Para no aumentar su complejidad en comparación con los receptores de capa única, la capa inferior, conocida como Enhanced Layer (EL), es tratada como un ruido adicional en la decodificación. Los receptores fijos aumentan su complejidad, ya que deben realizar un proceso de Cancelación de Interferencia (SIC) sobre la CL para obtener la EL. Para limitar la complejidad adicional de los receptores fijos, las capas de LDM en ATSC 3.0 están configuradas con diferentes capacidades de corrección, pero comparten el resto de bloques de la capa física, incluido el TIL, el PP, el tamaño de FFT, y el GI. Esta disertación investiga tecnologías avanzadas para optimizar el rendimiento de LDM. Primero se propone una optimización del proceso de demapeo para las dos capas de LDM. El algoritmo propuesto logra un aumento de capacidad, al tener en cuenta la forma de la EL en el proceso de demapeo de la CL. Sin embargo, el número de distancias Euclidianas a computar puede aumentar significativamente, conduciendo no solo a receptores fijos más complejos, sino también a receptores móviles más complejos. A continuación, se determina la configuración de piloto ATSC 3.0 más adecuada para LDM. Teniendo en cuenta que las dos capas comparten el mismo PP, surge una contrapartida entre la densidad de pilotos (CL) y la redundancia sobre los datos (EL). A partir de los resultados de rendimiento, se recomienda el uso de un PP no muy denso, ya que ya han sido diseñados para hacer frente a ecos largos y altas velocidades. La amplitud piloto óptima depende del estimador de canal en los receptores (ej., se recomienda la amplitud mínima para una implementación Wiener, mientras que la máxima para una implementación FFT). También se investiga la potencial transmisión conjunta de LDM con tres tecnologías avanzadas adoptadas en ATSC 3.0: las tecnologías de agregación MultiRF, los esquemas de MISO distribuido y los de MIMO colocalizado. Se estudian los potenciales casos de uso, los aspectos de implementación del transmisor y el receptor, y las ganancias de rendimiento de las configuraciones conjuntas para las dos capas de LDM. Las restricciones adicionales de combinar LDM con las tecnologías avanzadas se consideran admisibles, ya que las mayores demandas ya están contempladas en ATSC 3.0 (ej., una segunda cadena de recepción). Se obtienen ganancias significativas en condiciones de recepción peatonal gracias a la diversidad en frecuencia proporcionada por las tecnologías MultiRF. La conjunción de LDM con esquemas de MISO proporciona ganancias de rendimiento significativas en redes SFN para la capa fija con el esquema de Alamouti. / Since the beginning of the 21st century, terrestrial broadcasting systems have been blamed of an inefficient use of the allocated spectrum. To increase the spectral efficiency, digital television Standards Developing Organizations settled to develop the technical evolution of the first-generation DTT systems. Among others, a primary goal of next-generation DTT systems (DVB-T2 and ATSC 3.0) is to simultaneously provide TV services to mobile and fixed devices. The major drawback of this simultaneous delivery is the different requirement of each reception condition. To address these constraints different multiplexing techniques have been considered. While DVB-T2 fulfilled the simultaneous delivery of the two services by TDM, ATSC 3.0 adopted the LDM technology. LDM can outperform TDM and FDM by taking advantage of the UEP ratio, as both services, namely layers, utilize all the frequency and time resources with different power levels. At receiver side, two implementations are distinguished, according to the intended layer. Mobile receivers are only intended to obtain the upper layer, known as CL. In order not to increase their complexity compared to single layer receivers, the lower layer, known as EL is treated as an additional noise on the CL decoding. Fixed receivers, increase their complexity, as they should performed a SIC process on the CL for getting the EL. To limit the additional complexity of fixed receivers, the LDM layers in ATSC 3.0 are configured with different error correction capabilities, but share the rest of physical layer parameters, including the TIL, the PP, the FFT size, and the GI. This dissertation investigates advanced technologies to optimize the LDM performance. A demapping optimization for the two LDM layers is first proposed. A capacity increase is achieved by the proposed algorithm, which takes into account the underlying layer shape in the demapping process. Nevertheless, the number of Euclidean distances to be computed can be significantly increased, contributing to not only more complex fixed receivers, but also more complex mobile receivers. Next, the most suitable ATSC 3.0 pilot configuration for LDM is determined. Considering the two layers share the same PP a trade-off between pilot density (CL) and data overhead (EL) arises. From the performance results, it is recommended the use of a not very dense PP, as they have been already designed to cope with long echoes and high speeds. The optimum pilot amplitude depends on the channel estimator at receivers (e.g. the minimum amplitude is recommended for a Wiener implementation, while the maximum for a FFT implementation). The potential combination of LDM with three advanced technologies that have been adopted in ATSC 3.0 is also investigated: MultiRF technologies, distributed MISO schemes, and co-located MIMO schemes. The potential use cases, the transmitter and receiver implementations, and the performance gains of the joint configurations are studied for the two LDM layers. The additional constraints of combining LDM with the advanced technologies is considered admissible, as the greatest demands (e.g. a second receiving chain) are already contemplated in ATSC 3.0. Significant gains are found for the mobile layer at pedestrian reception conditions thanks to the frequency diversity provided by MultiRF technologies. The conjunction of LDM with distributed MISO schemes provides significant performance gains on SFNs for the fixed layer with Alamouti scheme. Last, considering the complexity in the mobile receivers and the CL performance, the recommended joint configuration is MISO in the CL and MIMO in the EL. / Des de començaments del segle XXI, els sistemes de radiodifusió terrestre han sigut culpats d'un ús ineficient de l'espectre assignat. Per a augmentar l'eficiència espectral, els organismes d'estandardització de TV digital van començar a desenvolupar l'evolució tècnica dels sistemes de TDT de primera generació. Entre altres, un dels objectius principals dels sistemes de TDT de pròxima generació (DVB-T2 i el ATSC 3.0) és proporcionar simultàniament serveis de TV a dispositius mòbils i fixos. El principal inconvenient d'aquest lliurament simultani són els diferents requisits de cada condició de recepció. Per a abordar aquestes limitacions, s'han considerat diferents tècniques de multiplexació. Mentre que DVB-T2 escomet el lliurament simultani dels dos serveis mitjançant TDM, ATSC 3.0 va adoptar la Multiplexació per Divisió en Capes (LDM). LDM pot superar a TDM i a FDM en aprofitar la relació de Protecció d'Error Desigual (UEP), ja que tots dos serveis, cridats capes, utilitzen tots els recursos de freqüència i temps amb diferents nivells de potència. En el costat del receptor, es distingeixen dues implementacions, d'acord amb la capa a decodificar. Els receptors mòbils solament estan destinats a obtenir la capa superior, coneguda com Core Layer (CL). Per a no augmentar la seua complexitat en comparació amb els receptors de capa única, la capa inferior, coneguda com Enhanced Layer (EL), és tractada com un soroll addicional en la decodificació. Els receptors fixos augmenten la seua complexitat, ja que han de realitzar un procés de Cancel·lació d'Interferència (SIC) sobre la CL per a obtenir l'EL. Per a limitar la complexitat addicional dels receptors fixos, les capes de LDM en ATSC 3.0 estan configurades amb diferents capacitats de correcció, però comparteixen la resta de blocs de la capa física, inclòs el TIL, el PP, la grandària de FFT i el GI. Aquesta dissertació investiga tecnologies avançades per a optimitzar el rendiment de LDM. Primer es proposa una optimització del procés de demapeo per a les dues capes de LDM. L'algoritme proposat aconsegueix un augment de capacitat, en tenir en compte la forma de l'EL en el procés de demapeo de la CL. No obstant açò, el nombre de distàncies Euclidianes a computar pot augmentar significativament, conduint NO sols a receptors fixos més complexos, sinó també a receptors mòbils més complexos. A continuació, es determina la configuració de pilot ATSC 3.0 més adequada per a LDM. Tenint en compte que les dues capes comparteixen el mateix PP, es produeix una contrapartida entre la densitat de pilots (CL) i la redundància sobre les dades (EL). A partir dels resultats de rendiment, es recomana l'ús d'un PP no gaire dens, ja que ja han sigut dissenyats per a fer front a ecos llargs i altes velocitats. L'amplitud pilot òptima depèn de l'estimador de canal en els receptors (ex., es recomana l'amplitud mínima per a una implementació Wiener, mentre que la màxima per a una implementació FFT). També s'investiga la potencial transmissió conjunta de LDM amb tres tecnologies avançades adoptades en ATSC 3.0: les tecnologies d'agregació de MultiRF, els esquemes de MISO distribuït i els de MIMO colocalitzat. S'estudien els potencials casos d'ús, els principals aspectes d'implementació del transmissor i el receptor, i els guanys de rendiment de les configuracions conjuntes per a les dues capes de LDM. Les restriccions addicionals de combinar LDM amb les tecnologies avançades es consideren admissibles, ja que les majors demandes ja estan contemplades en ATSC 3.0 (ex., una segona cadena de recepció). S'obtenen guanys significatius per a la capa mòbil en condicions de recepció per als vianants gràcies a la diversitat en freqüència proporcionada per les tecnologies MultiRF. La conjunció de LDM amb esquemes MISO distribuïts proporciona guanys de rendiment significatius en xarxes SFN per a la capa fixa amb l'esquema d'Alamouti. / Garro Crevillén, E. (2018). Advanced Layered Divsion Multiplexing Technologies for Next-Gen Broadcast [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/105559 / TESIS

The thesis deals with EEG signals, their description, methods of quantitative analysis and the processes in time-frequency domains, or power spectrums. The relationsheep between brain electrical activity and acustic stimuli (Mozart´s “Sonata K448”) was studied using EEG analysis in relation to sound impulses from replayed extracts of. The proposed experiment protocol included recording of EEG of volunteers. In order to visualize and analyze the data, the software with the graphic user interface was created, which enables topological mapping of brain activity and its vizualization in the time-frequency domain.

The doctoral thesis focuses on signal representation in the time-frequency domain with constant resolution. In theoretical introduction the possibilities of displaying a signal in time and frequency are summarized. Attention is concentrated on comparison of short-time Fourier Transform (STFT) and Wigner-Ville Distribution (WVD). The latter achieves a significantly better resolution, especially for a linearly modulated signal. The disadvantage of WVD, which is the presence of interferences resulting from the calculation of the instantaneous autocorrelation function, is described in detail. These interferences are due to the presence of multiple components in the signal or its non-linear modulation. Subsequently, several methods are discussed, which can suppress these interferences, but at the cost of resolution loss. One of the interference suppression methods is smoothed pseudo Wigner-Ville distribution. It is further used in this thesis for the analysis of interference suppression when various filtrations in the time-frequency plane are applied. Several signals with multiple components or various non-linear modulations are used. Based on the analysis, a method using a set of variously smoothed pseudo Wigner-Ville distributions is designed to estimate the time-frequency representation with high resolution and minimal interferences. To compare the results to other methods, the quantitative metrics used in the literature are compared. To select the appropriate one a new metric is suggested. It is applicable to simulated signals and uses mean square error. Based on the comparison, the Stankovi\' measure is selected as the most appropriate for comparing results. The selected metric is used to determine the appropriate minimal number of differently smoothed pseudo Wigner-Ville distributions. Using the selected metric, the proposed method is compared with other methods. These are STFT with optimized window length, S-method with optimized parameter and optimization method using radial Gaussian kernel (RGK). These methods are compared based on the set of signals previously used for interference suppression analysis. In addition, noises are added to the signals. Finally, the methods are also compared based on the real bat echo signal. In conclusion, the proposed method outperforms the compared methods in suppressing interference and resolution.