Le medium sans fil est une ressource partagée et limitée. Les normes sans fil actuelles partagent toujours le principe de partage du medium Half-Duplex: la transmission et la réception de signaux sont effectuées dans deux intervalles de temps distincts ou deux bandes de fréquences différentes. En outre, l'émetteur-récepteur ne peut émettre et recevoir qu’un signal à la fois. Cette thèse suit une autre approche: au lieu de partager le support avec le principe de Half-Duplex, toute la bande de fréquence autorisée est partagé pour la transmission et la réception simultanée, approche qui est appelée Full-Duplex. Dès lors, on peut concevoir une architecture d'un émetteur-récepteur radio flexible à large bande pour traiter deux types de signaux différents à la fois. Pour approcher cet objectif, nous utilisons une méthode de suppression active analogique de l’auto-interférence (AARFSIC) et l'annulation active numérique d'auto interférence dans le domaine temporel (ADSICT) pour annuler la forte auto-interférence (SI) induite par le principe Full-Duplex. Basé sur la radio Full-Duplex, nous proposons un système flexible Dual-Band (FDDB) émetteur-récepteur radio OFDM-Full Duplex en la combinant avec un front-end RF double bande. S'appuyant sur ces principes, nous exposons trois contributions principales: Nous présentons une technique d’annulation analogique de l’auto-interférence (ASIC), qui peut annuler complètement l’auto-interférence à trajet direct ou multi-trajets, basée sur la combinaison des méthodes AARFSIC et DSICT. Ensuite, nous présentons la conception et l'évaluation d'une radio OFDM Full-Duplex, y compris l'analyse et la qualification de l'impact du bruit thermique et du bruit de phase sur les performances du système. Enfin, nous développons une radio dual-bande FDDB OFDM qui peut fonctionner sur deux fragments de spectre séparés. Afin d'éliminer l'impact du déséquilibre I/Q sur la radio FDDB, une méthode d’estimation des déséquilibres I/Q et de compensation, simple mais efficace, est présentée. La simulation au niveau système menée avec ADS et Matlab montre que cette méthode peut effectivement compenser des déséquilibres I/Q aussi bien élevés que faibles. / The wireless medium is a shared and limited resource. Current wireless standards always share the medium with Half-Duplex principle: the transmission and reception of signals are done in two separate time slots or two different frequency bands. Besides, the transceiver can only transmit and receive one signal at a time. This dissertation takes an alternate approach: Instead of sharing the medium with Half-Duplex principle, the entire licensed frequency band is shared for simultaneous transmission and reception, which we call Full-Duplex. Besides, the design concept for a wideband flexible radio transceiver can process two different types of signals at a time. To approach this goal, we use an active analog radio frequency self-interference cancellation (AARFSIC) method or a combination scheme of the AARFSIC and active digital self interference cancellation in time domain (ADSICT) to cancel the strong self-interference (SI) induced by the Full-Duplex principle. Based on the Full-Duplex radio, we propose a flexible Full-Duplex Dual-Band (FDDB) OFDM radio transceiver by combining it with a Dual-Band RF front-end. Building on these, we make three main contributions: We present an active self-interference cancellation (ASIC) scheme, which can cancel both the strong one-path and multi-path SI completely, based on the combination of the AARFSIC and DSICT. Next, we introduce the design and evaluation of a Full-Duplex OFDM radio, including the analysis and qualification of the impact of the thermal noise and phase noise on the system performance. Finally, we develop a FDDB OFDM radio that can work on two separate spectrum fragments. In order to eliminate the impact of the I/Q imbalance on the FDDB radio, a simple but practical digital I/Q imbalance estimation and compensation method is presented. The system level simulation conducted with ADS and Matlab software shows that this method can effectively compensate both high and low I/Q imbalance.

<p>Master thesis work at ITN (Department of Science and Technology) in the areas of A/D-construction and RF-circuit design. Major goal of project were to research suitable possibilities for implementations of direct conversion in transceivers operating in the 160MHz band, theoretic study followed by development of components in the construction environment Cadence. Suitable A/D- converter and other important parts were selected at the end of the theoretic study. Subsampling technique was applied to make A/D sample requirements more realistic to achieve. Besides lowering requirements on A/D-converter it allows a more simple construction, which saves more components than subsampling adds. Subsampling add extra noise, because of that an A/D-converter based on the RSD algorithm was chosen to improve error rate. To achieve high bit-processing rate compared to the used number of transistors, pipeline structure were selected as conversion method. The receiver was that part which gained largest attention because it’s the part which is most interesting to optimise. A/D-conversion is more difficult to construct than D/A conversion, besides there’s more to gain from eliminating mixers in the receiver than in the transmitter.</p>

Master thesis work at ITN (Department of Science and Technology) in the areas of A/D-construction and RF-circuit design. Major goal of project were to research suitable possibilities for implementations of direct conversion in transceivers operating in the 160MHz band, theoretic study followed by development of components in the construction environment Cadence. Suitable A/D- converter and other important parts were selected at the end of the theoretic study. Subsampling technique was applied to make A/D sample requirements more realistic to achieve. Besides lowering requirements on A/D-converter it allows a more simple construction, which saves more components than subsampling adds. Subsampling add extra noise, because of that an A/D-converter based on the RSD algorithm was chosen to improve error rate. To achieve high bit-processing rate compared to the used number of transistors, pipeline structure were selected as conversion method. The receiver was that part which gained largest attention because it’s the part which is most interesting to optimise. A/D-conversion is more difficult to construct than D/A conversion, besides there’s more to gain from eliminating mixers in the receiver than in the transmitter.

Because of the tremendous amount of media streaming, video calling and high definition TV and gaming, the biggest challenge for the wireless industry is the increasing demand of high data rates. Utilization of mm-wave frequencies is an attractive option to meet this high demand. Recent advances in low cost semiconductor technologies allow realization of low-cost on-chip RF front-ends in the high millimeter wave (mm-wave) frequencies, making it possible to realize compact systems for these application areas. Although integrated circuits (ICs) are one of the main building blocks of a mm-wave system, in order to realize a fully functional wireless system, cost-effective antenna design and packaging are two important pre-conditions. Researchers have investigated and reported low-cost electronics packaging up to 100 GHz to a great extent on ceramic substrates, but mm-wave packaging above 100 GHz is relatively less explored, particularly on organic substrates. This Ph.D. dissertation demonstrates the design and development of microwave and mm-wave on-chip and on-package antennas and organically packaged components and modules ranging from 20 GHz to 170 GHz. The focus of this research was to design and develop mm-wave components and modules on LCP, to investigate the viability of this organic substrate and development of fabrication techniques in the K- (18-26.5 GHz), V- (50 to 70 GHz), W- (75 to 110 GHz), and D- (110 to 170 GHz) bands. Additionally, a demonstration of a micro-machined on-chip antenna has also been presented. This dissertation is divided in three parts: (1) characterization of liquid crystal polymer from 110 to 170 GHz. (2) development of highly radiation efficient on-chip and AiP antennas, and (3) development of mm-wave modules with the integration of antennas.

The primary reason for the wireless technology evolution is towards building capacity and obtaining higher data rates. Enclosed locations, densely populated campus, indoor offices, and device-to-device communication will require radios that need to operate at data rates up to 10 Gbps. In the next few years, a new generation of communication systems would emerge to better handle the ever-increasing demand for much wider bandwidth requirements. Simultaneously, key factors such as size, cost, and energy consumption play a distinctive role towards shaping the success of future wireless technologies. In the perspective of 3GPP 5G next generation wireless communication systems, the X band was explicitly targeted with a vast range of applications in point to point radio, point to multi point radio, test equipment, sensors and future wireless communication. An X-band RF front-end circuit for next generation wireless network applications is presented in this work. It details the design of a low noise amplifier and a power amplifier for X band operation. The designed amplifiers were integrated with a wideband single-pole-double-throw switch to achieve an overall front-end structure for 10 GHz. The design was carried out and sent for fabrication using a GaN 0.15µm process provided by NRC, a novel design kit. Due to higher breakdown voltage, high power density, high efficiency, high linearity and better noise performance, GaN HEMTs are a suitable choice for future wireless communication. Thus, the assumption is to further explore capabilities of this process in front-end design for future wireless communications.