In this thesis, power system transients are considered as an opportunity for development of on-line diagnostics of power components and specifically the insulation systems of power transformers and bushings. A new technique for on-line dielectric response measurement of power transformer bushings is proposed which utilizes natural transients in the power system, such as lightning and switching surges, as stimuli. Laboratory investigations are done on implementation of the proposed technique. Measurement considerations, data acquisition and processing involved in achievement of reasonable accuracy in the Dielectric Response (DR) are presented. Capability of the technique in tracking of the degradation signatures such as moisture content in the insulation has been evaluated and it has shown a good level of accuracy by being compared to the Frequency Domain Spectroscopy (FDS).  The proposed technique is tested on the service-aged 150 kV bushings and feasibility of the technique for monitoring of dielectric properties of power transformer bushings has been assessed; the results are promising for the technique to be used in the real application.  Partial Discharges (PD) behavior under transients has been also studied for different materials in this project. PD behavior of different defects, at different insulation condition, responding to the overvoltage transients in form of superimposed impulses on ac voltages was investigated and it was perceived how their distinctive response and the interpretation of  that, can be useful for their identification. Besides the conventional materials, surface ac PD properties of modified paper with silica and zinc oxide nanoparticles under the superimposed impulses have been assessed in this project. Proper type and optimum concentration level of nanoparticles in the paper are the factors that lead to the improvement of PD behavior in the modified paper under overvoltage transients. / <p>QC 20160525</p>

Development of the power gridtowards a more reliable and smarter system requires frequent on-line monitoring of the power components. Power transformers and their bushings are particularly important components in a power transmission system and their insulation degradation may lead to catastrophic failures. Time consuming and costly replacement of these components raise the importance of their frequent monitoring. A fault in a power transformer bushing can also involve in the failure of the transformer. Therefore, on-line diagnostics of power transformers and their bushings is of great interest. Several methods exist for diagnostics of these components. However, some of them can only be done off-line in maintenance periods, and the existing on-line methods generally provide less information, especially on the internal solid insulation parts. In this project, a new technique for on-line diagnostics of the power transformer and the bushing insulation is proposed. In this technique, natural transients happening in the power system such as lightning and switching surges can be used as stimuli for on-line dielectric response measurements. This technique can provide information on insulation close to what Dielectric Spectroscopy offers in off-line measurements. The wide-ranging frequency content of power system transients is their advantage for being usedas stimuli when measuring the Dielectric Response. The response can have particular signatures due to different types of defects in the insulation varying with frequency. Oil-impregnated paper as a major insulation component in power transformer and its bushing has been investigated in this project. Moisture content and temperature, as two important degradation factors in this type of insulation, have been studied to evaluate the performance of the proposed technique in the diagnostics of the oil-impregnated paper. The results are verified with the dielectric response obtained through commercial instruments. The results show that the proposed technique has the ability to track the changes in dielectric response due to the moisture content and temperature. Measurements were done at both highvoltage (40kV) and low voltage (10V) levels, and the corresponding circuit models to achieve reasonable accuracy for the results are discussed. Moving on from the material samples, a further study was done on three service-aged 150 kV bushings to investigate the feasibility of the technique on the diagnostics of power transformer bushings. Their dielectric response measured by the transient stimuli showed good agreement with their response obtained by the commercial instruments. The effect of the transformer winding on the transient response of the bushing is a further aspect of the real conditions for on-line diagnostics. This has been investigated through the simulation of transient models for transformers and bushings, and possible solutions for distinguishing the responses are presented. The proposed new on-line diagnostics technique by utilizing natural transients can provide information about the insulation system in a certain range of frequency without interrupting the operation or requiring an external voltage source. However, the validity range of the results depends on the bandwidth of the applied transients and other measurement considerations. This approach can be valuable in frequent monitoring of dielectric properties of the power transformers and their bushings as a complement to the other available on-line techniques. / <p>QC 20140409</p>

An electrical bushing is one of the most important elements in a power transformer. Steep front surges such as transient impulse voltage from lightning strikes is an inevitable electromagnetic transient mostly happening in power transmission and distribution system. The bushing might lead to be degraded due to such kind of surge. This project deals with overvoltage stress distribution on the transformer bushing under the effect of electromagnetic transient response such as lightning impulse.  To understand the behavior of transient response on the bushing, a proper model of power transformer bushing is built-in Comsol multiphysics to authenticate the stress distribution. The electromagnetic wave of impulse propagates onto the overhead line that connects with the transformer. Some understanding of the transient behavior of a conductor bushing has been achieved through studying the influence of inductance property and the skin effect characteristics of a multi-layer coaxial cable on the wave propagation, which has been structured in this project to simplify the model. On the other hand, the skin effect analysis on the conductor of the bushing has been taken also into account in this project using real conductor simulation in the Comsol model. Thus, it will be interesting to compare the real conductor model with the perfect conductor of the bushing through analyzing the current density effect on it.  In this project, multi-layer of coaxial cable and transformer bushing are simulated. The simulation is carried out for time domain and frequency domain in Comsol based on the model characteristics. / En elektrisk genomföring är ett av de viktigaste elementen i en transformator. Spänningsvågor med branta fronter som impulsspänningar från blixtnedslag är ett oundvikligt elektromagnetiskt övergående fenomen som oftast sker i kraftöverförings- och distributionssystem. Genomföringen kan leda till att degraderas på grund av en sådan våg. Detta projekt handlar om fördelning av överspännings på transformatorgenomföringen under påverkan av elektromagnetisk transient respons, såsom blixtimpuls.  För att förstå beteendet hos övergående respons på genomföringen är en korrekt modell av transformatorgenomföring inbyggd Comsol-flerfysik för att autentisera spänningsfördelningen. Den elektromagnetiska impulsvågen fortplantas från luftledningen som ansluter till transformatorn. Viss förståelse för det övergående beteendet hos en ledargenomföring har uppnåtts genom att studera påverkan av induktansegenskaper och hudeffektegenskaperna hos en flerskikts koaxialkabel på vågutbredningen, vilket har strukturerats i detta projekt för att förenkla modellen. Å andra sidan har hudeffektanalysen på genomföringens ledare beaktats i detta projekt med användning av verklig ledarsimulering i Comsol-modellen. Således blir det intressant att jämföra den riktiga ledarmodellen med den perfekta ledaren för genomföringen genom att analysera strömtäthetseffekten på den.  I detta projekt simuleras flerskikt av koaxialkabel och transformatorgenomföring. Simuleringen utförs för tidsdomän och frekvensdomän i Comsol baserat på modellegenskaperna.

The overall reliability of a power transformer depends to a great extent on the sound operation of the bushings thereof. In view of its overwhelming advantages, resin impregnated paper (RIP) is acquiring prominence over conventional oil impregnated paper (OIP) in transformer bushings. The main advantages of RIP bushings are low dielectric loss and capability of positioning them at any desired angle over the transformer. The RIP structure, being an all-solid system, is completely free from oil phase. The temperature rise in RIP bushings under normal operating conditions is seen to be a difficult parameter to control in view of the limited options for effective cooling. The degradation of dry-type insulation such as RIP is often due to thermal and electrical stresses. The long time performance thereof, depends strongly, on the maximum operating temperature. In order to be able to predict the regional temperature, it is necessary to consider the thermal and electrical parameters of insulation in question; and to identify and solve the governing equations under the relevant boundary conditions. Electrical failure of insulation is known to be an extremal random process wherein nominally identical specimens of equipment insulation, at constant stress fails at inordinately different times. In order to be able to estimate the life of power equipment like transformer bushing, it is necessary to run long duration ageing experiments under accelerated stresses, to acquire and analyze insulation specific failure data. The present work is an attempt to provide reliability and life estimation of High Voltage RIP bushing insulation. The literature survey carried out in this view indicate that investigation on thermal and electric field distribution and the models for failure under combined stress and analysis of the data so as to be able to estimate the possible life of RIP bushing is scanty. Having these aspects in focus, the scope of the present work is defined as: (i) Mapping of the temperature and electric field distribution in the body of 400kV RIP bushing (ii) Deduction of parameters of the probabilistic models for the failure under electrical and thermal ageing (iii) Estimation of life based on diagnostic testing using PD With this in view, the temperature distribution in the body of a 400kV RIP bushing is studied considering the heat generation both in central conductor and that in the insulation. Presence of multiple materials with non-confirming interfaces makes analytical solution rather difficult and hence numerical approach is adopted. In the present work, vertex-centered Finite Volume Method (FVM) is employed for both thermal and electrical analysis. The electric stress distribution is accurately evaluated considering both the non-zero conductivity of the RIP material and the presence of capacitive grading foils. These analysis has clearly shown that Stress grading foils uniforms the stress across the major portion of the bushing insulation Enhancement of the electric conductivity by the temperature is not found to be affective in changing the electric field distribution The temperature distribution is shown to have a maxima near the flange due to the influence of top oil temperature of the transformer Heat generated in the dielectric due to the prevailing electric stress is shown to be insignificant. This ruled out the possibility of thermal runaway and hence the dielectric temperature is within the safe working limits for the bushing considered. The deduction of physical models governing insulation failure depends on the nature of stress. In this work, the insulation failure at constant accelerated stress has been considered and the estimation of life is computed based on inverse power law coupled with Arrhenius law. A high degree of scatter is generic to the experimental data forming the ingredients to develop the models. In view of this, the concept of a random process is invoked. Probabilistic models for the failure of RIP bushing under synergy are adopted and an attempt is made to estimate the life. The well known Weibull distribution and probability plotting of life data is used in this endeavor. The maximum likelihood estimation is used to determine the scale and shape parameters of the Weibull distribution. In the diagnosis of the extent of degradation of insulation due to PD, under long duration electric stress, a non-conventional voltage application method called the classical stepped stress method is adopted. In this technique, the voltage is applied in pre-determined steps over predetermined duration of time. The magnitude of voltage steps is carefully computed based on Miners law and the end-of-life is computed using inverse power law. In summary, this thesis work has contributed to the thermal and electrical degradation of resin impregnated paper insulation for high voltage transformer bushing. The thermal and electrical field distributions computed in the body of bushing clearly shown that these stresses are well within the limit, thereby ruling out the possibility of a thermal runaway. Comparing the estimates of the most probable life of RIP, based on several methods appears to show that any of the method can be adopted. However, as matter of caution and safety, the lowest among them can be taken as a reasonable estimate.