The final thesis deals with the design of the steel loadbearing structure of the shopping center situated in Brno. The built-up floor area is 1973 m2 (L-shaped ground plan with dimensions 48 m x 50 m). The construction consists of three parts. Building A has four above-ground floors and reaches a height of 25.5 m. The steel structure of mono-pitched roof is designed in two options. Both options consist of full-length purlins and truss girders. Building B is a single-storey building with a mono-pitched roof top reaching 8.1 m high. Building C is three-storey with a flat roof. The first floor has a construction height of 4.5 m and the remaining two floors reach height of 3.6 m, which coincide with building A. The steel structure is made of steel-concrete composite ceilings and pin-supported columns. In the case of bracings, pressure was eliminated by means of non-linearities.The work includes proposal, assessment of the supporting structure and calculation of the directional details. Internal forces were determined based on a static analysis in the SCIA Engineer calculation program.

The aim of the final thesis is design of boarding house and horse stables. The boarding house has two floors, partial basement and exploited attic. The building is designed as rectangle and will serve as support area for guests´accommodation. The building has saddle roof. The main material of vertical and horizontal structures is cast-in-place concrete using formwok VELOX. The second building is horse stables. The building has two floors, partial basement and partial exploited attic for storing fodder. The L-shaped building will serve as stable for eleven horses, storage of fodder and garage for agricultural equipment. The building has saddle roof with truss girders. The main material of vertical and horizontal structures is cast-in-place concrete using formwok VELOX. These buildings are designed on slightly sloping terrain from east to west.

The subject of this master’s thesis is the design and assessment of footbridge in Železný Brod across the Jizera river. The preliminary assessment contains 3 different variants of footbridges. Based on the multi-criteria analysis will be chosen the most suitable type for detailed design. Detailed static analysis contains assessment of the main load-bearing parts of the structure including joints. The length of span is 60,0 m and the width of passage is 2,5 m. The structure is made of steel class S355 and S460.

Tato diplomová práce představuje určenou část projektové dokumentace ve stupni pro provádění stavby (dle vyhlášky č. 499/2006 Sb. ve znění vyhlášky č. 62/2013 Sb.) zabývající se komplexní rekonstrukcí a vytvořením nástavby stávající budovy školního ubytovacího zařízení ve městě Bzenci. Zároveň dojde ke změně užívání stavby na nájemní dům s byty charakteru sociálního bydlení. V souvislosti s touto skutečností se navržená rekonstrukce snaží zachovat a využít stávající konstrukce v co největším rozsahu, s cílem nezbytně tak nenavyšovat náklady rekonstrukce stavby.

The aim of diploma thesis is to design and assess a multipurpose hall building in the area of Brno. The shape of the hall is rectagular with dimensions 30,0 x 84,0 m. Roofing stucture is disegned and assessed in three versiions. Variant A is designed as a sadle - type truss from the CSH profile. Variant B is designed as a square - type truss from the CHS prosile. Variant C is designed as a arched truss from the CSH profile. These versions are compared by weight, manufacturing complexity and appearance. Preferable version is processed in detail. The work also includes a static calculation of the supporting elements, joints and drawing documentation..

The diploma thesis deals with project documentation for the realization of the sports centre in Zlín. Object is located on the edge of the city Zlín in build-up area of the sports halls. Object is defined from two sides by major roads, that are connected with family and residential buildings. Building site of the object is sligtly sloping, however with ground adapting adjusts into seeming flat land. The hall is devided on three operation parts. First and dominant unit is formed by gaming area with grandstrand, corresponding facilities included. Second unit is formed by mountaineering wall, corresponding included. Third unit is formed by bar, corresponding facilities included. Object is drafted with consideration of the Baťas architecture. Object is designed like a skeleton construction with combinated system of frames. Main supporting vertical construction of skeleton is designed from reinforced prefabricated concrete column. Main supporting horizontal construction of skeleton is designed like a system solution slimfloor, that is based on placing prestressed segment onto bottom side of a special beam Deltabeam. Within the main supporting construction is designed stifenner and construction of grandstrand as well, maid from reinforced prefabricard concrete. Sheathing of the object is combinated. From the second floor is designed system from thermal insulated sandwich panels, which is anchored into the pre-set steel construction. Roof is designed as a flat roof with trapezoidal metal sheet with thermal insulation and waterproofing layer made from m-PVC. Fillings of the object including light curtain wall is designed from system Schüco.

The aim of the diploma thesis is make a structural design of load carrying steel structure of terminal international airport Brno. The project is designed in two options. The height of the building in highest point is 15 m. The object has rectangular ground floor plan with proportions of 80 x 40 m. For selected option the check of joints and anchorage is performed as well as the design drawings. The object was designed according to currently valid standarts to the ultimate limit states and serviceability limit states.

Diploma thesis deals with desing and static assessment of supporting steel roof structure of velodrom. Climatic load is determined for location of city Znojmo. The thesis consists of technical report with comparison of 2 options solution, technical report of chosen variant, static report of main supporting parts and chosen connections, bill of materials quantities and drawing documentation. Computational model for evaluation of internal forces is realized in SCIA ENGINEER 17.01 software. Static report is created manually according to valid European standards.

The subject of this diploma thesis is design and check of two steel structures. A production hall with a floor plan dimensions 24x50 m and an administrative building with floor plan dimensions 54x30 m. Both buildings are situated in Prostějov. The structure of the production hall has a roof pitched at 12%. The main frames have 6 m centre to centre spacing. The design of the production hall is processed in two options. The administrative building has 4 floors. The floor structures are made of composite steel and concrete structure. The structure is stabilized by vertical bracings in both directions. The computational model of both structures was built up using SCIA Engineer software.

This thesis deals with structural design of a steel frame footbridge with wheelchair access, which will lead pedestrian and cyclists‘ traffic over the river Thaya in Břeclav. The footbridge is a structure of one field, lightness of a bridge opening is 58,92 m and a span length is 60,25 m. A light width of an area between rails is 2,5 m. The footbridge is constructed of a truss beam cable – stayed bridge on an oblique pylon of 20,0 m length and a preloaded steel suspender. The thesis was processed according to valid standards ČSN EN.