Commercial aviation transportation has experienced an overwhelming growth over the years. However, this expansion has encountered an important barrier: noise. Several studies have shown that residents in these areas experience problems such as stress and sleep disturbance. These problems have translated into demands for a better quality of life from airport residents which in turn have translated into more stringent aircraft noise regulations. As a result, large amounts of resources have been diverted towards the improvement of existing noise attenuation technologies and the development of more effective ones. In terms of turbofan generated noise, the most widely used technology is that of absorbent materials or liners. In recent investigations Alonso et al. have combined Herschel/Quincke (HQ) tubes with liners. This combination has the potential of effectively controlling pure tones and broadband noise in inlet sections of modern turbofan engines. Since a comprehensive approach for engine noise reduction will involve both inlet and aft HQ-Liner systems, additional research efforts were needed to evaluate their performance at reducing aft fan radiation In the present work, a combination of traditional liners and Herschel/Quincke waveguide resonators for aft fan radiation control is proposed. A theoretical model is developed in order to predict noise reduction due to such systems. The newly developed tool was then utilized to design an HQ-liner that was installed and tested in the aft section of the NASA Active Noise Control Fan (ANCF) rig. This experimental data was utilized to prove the potential of these systems and to validate the mathematical model. Analytical predictions correlate well with experiments. The NASA ANCF rig is not representative of a real turbofan engine. In order to assess the behavior of HQ-Liners in a more realistic environment a new system was specifically designed for a generic turbofan engine and its performance analyzed. The sound field inside HQ tubes has been described assuming plane waves only. This assumption limits the model to frequencies below the tube first resonance. In order to overcome this limitation a new model accounting for higher order modes inside the tubes has been developed. / Ph. D.

The combination of traditional passive acoustic liners with Herschel-Quincke (HQ) waveguides is proposed in this work as a device for Turbofan Engine Noise Control. The approach consists of installing circumferential arrays of HQ tubes on the lined sector of the inlet of a turbofan engine. A theoretical model is developed to predict the performance of this system assuming that the engine inlet is a circular lined duct with uniform mean flow. The tube-duct interfaces are modeled as finite piston sources that couple the sound field inside the duct with the dynamics of the HQ tubes. The finite piston source radiation is modeled in terms of a new closed form Green's function, which is found as the solution of the non-homogeneous convected acoustic wave equation with soft wall boundary conditions. The Green's function is extended from a point source to a finite piston by using the Divergence Theorem in the appropriate form. The dynamics of the HQ tube are both modeled as plane waves inside a straight tube and experimentally determined. The experimental determination of the HQ-dynamics is undertaken using impedance tubes with a 4-microphone technique. The newly developed theoretical model was used to predict the performance of a combined HQ-Liner system, which was tested on a scale simulated turbofan rig. The model is validated for broadband noise with the experimental data obtained from this test rig. The analytical predictions are shown to correlate well with experimental data. The results of the application of a HQ-Liner on a turbofan engine show a great potential in order to improve the performance of traditional passive acoustic liners. / Ph. D.

Community noise impact is an important factor in design of current generation aircraft, especially when considering projected trends in flight volume and urbanization. Simulation is a useful tool to evaluate the human annoyance response due to both current and proposed aircraft, and it has some advantages over field studies or playback of recordings. However, current simulation methods which are based on time-averaged prediction methods do not include short term fluctuations observed in recordings of real aircraft engines. Those fluctuations in both tonal and broadband sources provide psychoacoustic clues to listeners when evaluating flyover noise realism. When those short-term fluctuations are not included, simulation realism may suffer and evaluation results might not be applicable to real aircraft. This thesis presents work to analyze and model fluctuations in aircraft engine fan noise, using an existing set of static turbofan engine recordings. The inclusion of the observed fluctuations, which are unaccounted for in many current prediction and simulation routines, was expected to increase the perceived realism of simulated flyover events. The analysis of tonal fluctuations was performed by utilizing the complex-valued analytic signal to extract instantaneous amplitude and frequency. A simple parametric model was developed to represent each measured fluctuation using its spectral bandwidth and variance. The model was then used to generate new fluctuations which were perceptually similar to the original. Tonal synthesis was performed as the sum of many amplitude- and frequency-modulated tones. Analysis was also performed on the broadband fan noise component, which used output from the Short-Time Fourier Transform was used to characterize fluctuations in third-octave band SPL. Those fluctuations were not modeled as in the case of tonal fluctuations and were directly reproduced using an overlap-add synthesis tool. A subjective listening test was then conducted to evaluate the perceptual similarity between synthesized and recorded fan noise. That test concluded that synthesized tonal noise which included short-term fluctuations was perceived as more realistic than noise without. It also concluded that the addition of broadband fan noise components tended to mask tonal fluctuations. / Master of Science

An innovative application of existing technology is proposed for attenuating the effects of transient phenomena, such as rotor-stator and rotor-strut interactions, linked to noise and fatigue failure in turbomachinery environments. A computational study was designed to assess the potential of Passive Porosity Technology as a mechanism for alleviating interaction effects and radiated noise by reducing the fluctuating forces acting on the vane surfaces. The study involved a typical high bypass fan stator airfoil immersed in a subsonic free field and exposed to the effects of a transversely moving wake. Time histories of the primitive aerodynamic variables obtained from Computational Fluid Dynamics (CFD) calculations were input into an acoustic prediction code to estimate noise levels at a radial distance of ten chords from the stator airfoil. This procedure was performed on the solid airfoil to obtain a baseline, and on approximately fifty porous configurations in order to isolate those that would yield maximum noise reductions without compromising the aerodynamic performance of the stator. It was found that, for a single stator immersed in a subsonic flow field, communication between regions of high pressure differential - made possible by the use of passive porosity - tends to induce a time-dependent oscillatory pattern of small inflow-outflow regions near the stator leading edge (LE), which is well established before wake effects come into play. The oscillatory pattern starts at the LE, and travels downstream on both suction and pressure sides of the airfoil. The amplitude of the oscillations seemed to be proportional to the extension of the porous patch on the pressure side. Regardless of this effect, which may not have occurred if the airfoil were placed within a stator cascade, communication between regions of high pressure differential is necessary to significantly alter the noise radiation pattern of the stator airfoil. Whether those changes result in noise abatement or enhancement depends primarily on the placement and extension of the porous patches. For most viable configurations, porosity reduced loading noise but increased thickness noise. Variations in nominal porosity were of secondary importance. In general, the best aerodynamic performers (i.e., those configurations that were able to reduce unsteady lift without severely altering the lift and/or drag characteristics of the solid airfoil) were also the best acoustic performers. As a result of using passive surface porosity, overall peak radiated noise was reduced by approximately 1.0 dB. This reduction increased to about 2.5 dB when the effects of loading noise alone were considered. / Ph. D.

Résumé: Cette dissertation s’intéresse aux méthodes numériques dans le domaine de l’acoustique. Les propriétés acoustiques d’un produit sont devenues une part intégrante de la conception. En effet, de nos jours le bruit est perçu comme une nuisance par le consommateur et constitue un critère de vente. Il y a de plus des normes à respecter. Les méthodes numériques permettent de prédire la propagation sonore et constitue dès lors un outil de conception incontournable pour réduire le temps et les coûts de développement d’un produit. Cette dissertation considère la propagation d’ondes acoustiques dans le domaine fréquentiel en tenant compte de la présence d’un écoulement. Nous pouvons citer comme application industrielle, le rayonnement d’une nacelle de réacteur d’avion. Le but de la thèse est de proposer une nouvelle méthode et démontrer ses performances par rapport aux méthodes actuellement utilisées (i.e. la méthode des éléments finis). L’originalité du travail consiste à étendre la méthode de partition de l’unité polynomiale dans le cadre de la propagation acoustique convectée, pour des domaines extérieurs. La simulation acoustique dans des domaines de dimensions infinies est réalisée dans ce travail à l’aide d’un couplage entre éléments finis et éléments infinis. La dissertation présente la formulation de la méthode pour des applications axisymétriques et tridimensionnelles et vérifie la méthode en comparant les résultats numériques obtenus avec des solutions analytiques pour des applications académiques (i.e. propagation dans un conduit, rayonnement d’un multipole, bruit émis par la vibration d’un piston rigide, etc.). Les performances de la méthode sont ensuite analysées. Des courbes de convergences illustrent à une fréquence donnée, la précision de la méthode en fonction du nombre d’inconnues. Tandis que des courbes de performances présentent le temps de calcul nécessaire pour obtenir une solution d’une précision donnée en fonction de la fréquence d’excitation. Ces études de performances montrent l’intérêt de la méthode présentée. Le rayonnement d’un réacteur d’avion a été abordé dans le but de vérifier la méthode sur une application de type industriel. Les résultats illustrent la propagation pour une nacelle axisymétrique en tenant compte de l’écoulement et la présence de matériau absorbant dans la nacelle et compare les résultats obtenus avec la méthode proposée et ceux obtenus avec la méthode des éléments finis. Les performances de la méthode de la partition de l’unité dans le cadre de la propagation convectée en domaines infinis sont présentées pour des applications académiques et de type industriel. Le travail effectué illustre l’intérêt d’utiliser des fonctions polynomiales d’ordre élevé ainsi que les avantages à enrichir l’approximation localement afin d’améliorer la solution sans devoir créer un maillage plus fin. Summary: Environmental considerations are important in the design of many engineering systems and components. In particular, the environmental impact of noise is important over a very broad range of engineering applications and is increasingly perceived and regulated as an issue of occupational safety or health, or more simply as a public nuisance. The acoustic quality is then considered as a criterion in the product design process. Numerical prediction techniques allow to simulate vibro-acoustic responses. The use of such techniques reduces the development time and cost. This dissertation focuses on acoustic convected radiation in outer domains such as it is the case for turbofan radiation. In the current thesis the mapped infinite partition of unity method is implemented within a coupled finite and infinite element model. This method allows to enrich the approximation with polynomial functions. We present axisymmetric and three-dimensional formulations, verify and analyse the performance of the method. The verification compares computed results with the proposed method and analytical solutions for academic applications (i.e. duct propagation, multipole radiation, noise radiated by a vibrating rigid piston, etc.) . Performance analyses are performed with convergence curves plotting, for a given frequency, the accuracy of the computed solution with respect to the number of degrees of freedom or with performance curves, plotting the CPU time required to solve the application within a given accuracy, with respect to the excitation frequency. These performance analyses illustrate the interest of the mapped infinite partition of unity method. We compute the radiation of an axisymmetric turbofan (convected radiation and acoustic treatments). The aim is to verify the method on an industrial application. We illustrate the radiation and compare the mapped infinite partition of unity results with finite element computations. The dissertation presents the mapped partition of unity method as a computationally efficient method and illustrates its performances for academic as well as industrial applications. We suggest to use the method with high order polynomials and take the advantage of the method which allows to locally enrich the approximation. This last point improves the accuracy of the solution and prevent from creating a finer mesh.

In this study, acoustic noise radiation through a duct in frequency domain is analyzed. Frequency domain linearized Euler equations are solved for turbofan exhaust noise propagation and radiation. The geometry in studied cases is assumed as axisymmetric. The acoustic waves are decomposed into periodic azimuthal modes. Characteristic boundary conditions, and buffer zone boundary conditions are employed. Iterative type pseudo time integration is employed. Nonuniform background flow effect on the radiation pattern is experienced. All computations are performed in parallel using MPI library routines in computer cluster. Results proved that the one with the buffer zone has a better radiation characteristic than the characteristic one because of absorbtion of spurious waves. It is seen that the efficiency of the buffer zone is frequency dependent.

Résumé:<p><p>Cette dissertation s’intéresse aux méthodes numériques dans le domaine de l’acoustique. Les propriétés acoustiques d’un produit sont devenues une part intégrante de la conception. En effet, de nos jours le bruit est perçu comme une nuisance par le consommateur et constitue un critère de vente. Il y a de plus des normes à respecter. Les méthodes numériques permettent de prédire la propagation sonore et constitue dès lors un outil de conception incontournable pour réduire le temps et les coûts de développement d’un produit.<p><p>Cette dissertation considère la propagation d’ondes acoustiques dans le domaine fréquentiel en tenant compte de la présence d’un écoulement. Nous pouvons citer comme application industrielle, le rayonnement d’une nacelle de réacteur d’avion. Le but de la thèse est de proposer une nouvelle méthode et démontrer ses performances par rapport aux méthodes actuellement utilisées (i.e. la méthode des éléments finis).<p><p>L’originalité du travail consiste à étendre la méthode de partition de l’unité polynomiale dans le cadre de la propagation acoustique convectée, pour des domaines extérieurs. La simulation acoustique dans des domaines de dimensions infinies est réalisée dans ce travail à l’aide d’un couplage entre éléments finis et éléments infinis.<p><p>La dissertation présente la formulation de la méthode pour des applications axisymétriques et tridimensionnelles et vérifie la méthode en comparant les résultats numériques obtenus avec des solutions analytiques pour des applications académiques (i.e. propagation dans un conduit, rayonnement d’un multipole, bruit émis par la vibration d’un piston rigide, etc.). Les performances de la méthode sont ensuite analysées. Des courbes de convergences illustrent à une fréquence donnée, la précision de la méthode en fonction du nombre d’inconnues. Tandis que des courbes de performances présentent le temps de calcul nécessaire pour obtenir une solution d’une précision donnée en fonction de la fréquence d’excitation. Ces études de performances montrent l’intérêt de la méthode présentée.<p><p>Le rayonnement d’un réacteur d’avion a été abordé dans le but de vérifier la méthode sur une application de type industriel. Les résultats illustrent la propagation pour une nacelle axisymétrique en tenant compte de l’écoulement et la présence de matériau absorbant dans la nacelle et compare les résultats obtenus avec la méthode proposée et ceux obtenus avec la méthode des éléments finis.<p><p>Les performances de la méthode de la partition de l’unité dans le cadre de la propagation convectée en domaines infinis sont présentées pour des applications académiques et de type industriel. Le travail effectué illustre l’intérêt d’utiliser des fonctions polynomiales d’ordre élevé ainsi que les avantages à enrichir l’approximation localement afin d’améliorer la solution sans devoir créer un maillage plus fin.<p><p><p>Summary:<p><p>Environmental considerations are important in the design of many engineering systems and components. In particular, the environmental impact of noise is important over a very broad range of engineering applications and is increasingly perceived and regulated as an issue of occupational safety or health, or more simply as a public nuisance. The acoustic quality is then considered as a criterion in the product design process. Numerical prediction techniques allow to simulate vibro-acoustic responses. The use of such techniques reduces the development time and cost.<p><p>This dissertation focuses on acoustic convected radiation in outer domains such as it is the case for turbofan radiation. In the current thesis the mapped infinite partition of unity method is implemented within a coupled finite and infinite element model. This method allows to enrich the approximation with polynomial functions. <p><p>We present axisymmetric and three-dimensional formulations, verify and analyse the performance of the method. The verification compares computed results with the proposed method and analytical solutions for academic applications (i.e. duct propagation, multipole radiation, noise radiated by a vibrating rigid piston, etc.) .Performance analyses are performed with convergence curves plotting, for a given frequency, the accuracy of the computed solution with respect to the number of degrees of freedom or with performance curves, plotting the CPU time required to solve the application within a given accuracy, with respect to the excitation frequency. These performance analyses illustrate the interest of the mapped infinite partition of unity method.<p><p>We compute the radiation of an axisymmetric turbofan (convected radiation and acoustic treatments). The aim is to verify the method on an industrial application. We illustrate the radiation and compare the mapped infinite partition of unity results with finite element computations.<p><p>The dissertation presents the mapped partition of unity method as a computationally efficient method and illustrates its performances for academic as well as industrial applications. We suggest to use the method with high order polynomials and take the advantage of the method which allows to locally enrich the approximation. This last point improves the accuracy of the solution and prevent from creating a finer mesh.<p> / Doctorat en Sciences de l'ingénieur / info:eu-repo/semantics/nonPublished