This thesis deals with one-dimensional (1D) and two-dimensional nanomaterials (2D) in terms of their utilization for new types of gas sensors. Thesis focuses on study of sensing elements for gas sensors based on semiconductor metal oxide materials (MOX) and their manufacturing technology. The objective of the thesis is the design and implementation of a sensing elements formed by selected nanomaterials based on the structure of interdigital electrodes. The result of the practical part of the thesis is the characterization and comparison of materials in terms of their detection parameters in the presence of selected test gases. The first part of thesis hierarchically defines chemoresistive gas sensor, characterizes and explains its operation principle. Second part studies 1D and 2D nanomaterials of sensing elements for MOX chemoresistive gas sensors, contains a research of their properties and describes their methods of manufacturing and implementation. The last part deals with the implementation of the sensitive layer of the sensor with selected nanomaterials, characterizes and compares their detection properties.

The subject of my thesis is a static analysis of a different trusses of a great span length. The preface is devoted to the trusses their creation of plane models of a girder with the extent of 18 metres. The questions of construction´s joints are mainly solid. The conclusion is dedicated to the creation of the girder and joints´ formation.

abstract: Two-dimensional quantum materials have garnered increasing interest in a wide variety of applications due to their promising optical and electronic properties. These quantum materials are highly anticipated to make transformative quantum sensors and biosensors. Biosensors are currently considered among one of the most promising solutions to a wide variety of biomedical and environmental problems including highly sensitive and selective detection of difficult pathogens, toxins, and biomolecules. However, scientists face enormous challenges in achieving these goals with current technologies. Quantum biosensors can have detection with extraordinary sensitivity and selectivity through manipulation of their quantum states, offering extraordinary properties that cannot be attained with traditional materials. These quantum materials are anticipated to make significant impact in the detection, diagnosis, and treatment of many diseases. Despite the exciting promise of these cutting-edge technologies, it is largely unknown what the inherent toxicity and biocompatibility of two-dimensional (2D) materials are. Studies are greatly needed to lay the foundation for understanding the interactions between quantum materials and biosystems. This work introduces a new method to continuously monitor the cell proliferation and toxicity behavior of 2D materials. The cell viability and toxicity measurements coupled with Live/Dead fluorescence imaging suggest the biocompatibility of crystalline MoS2 and MoSSe monolayers and the significantly-reduced cellular growth of defected MoTe2 thin films and exfoliated MoS2 nanosheets. Results show the exciting potential of incorporating kinetic cell viability data of 2D materials with other assay tools to further fundamental understanding of 2D material biocompatibility. / Dissertation/Thesis / Masters Thesis Materials Science and Engineering 2019

The ozone decomposition reaction was performed in a 2.5cmx40cmx450cm two dimensional (2D) catalytic fluidized bed reactor. Commercial FCC catalyst impregnated with Fe2O3 was used at superficial gas velocities ranging between 0.006 m/s and 0.55 m/s. The onset velocity of the turbulent regime (uc) was determined as 0.4 m/s. The catalyst activity was optimized so that the effect of inter-phase mass transfer could be accentuated in the conversion reading. It was found that the general bubbling-turbulent model of Thompson et. al. (1999) combined with the mass transfer correlations of Kunii and Levenspiel (1991), Foka et. al. (1996) and Miyauchi et. al. (1980)gave reasonable predictions of the experimental data. The gradual improvement of reactor performance with an increase in superficial velocity (as predicted by the Thompson et. al. model) was not observed; instead a discontinuity of the reactor performance was noted in the vicinity of uc. More experimental work is required to substantiate this observation. Copyright / Dissertation (MEng)--University of Pretoria, 2009. / Chemical Engineering / unrestricted

Ce travail de thèse concerne l’étude de nouveaux matériaux hybrides organiques-inorganiques lamellaires magnétiques et luminescents synthétisés par voie hydrothermale. Ces matériaux ont été obtenus à partir de sels de métaux de transition de configuration électronique 3d (Cu2+, Co2+, Mn2+, Zn2+) et de molécules organiques de basse symétrie constituées d’au moins un acide phosphonique greffé sur une plateforme rigide aromatique (phényle ou naphtalène). Le choix du cation métallique ainsi que l’ajout d’autres fonctions (halogène : F, Cl, Br, I, acide carboxylique ou méthyle) sur ces systèmes cycliques ont conduit à des matériaux hybrides bidimensionnels aux architectures et propriétés physiques (luminescence, magnétisme et/ou couplage magnétoélectrique) diverses. La compréhension du lien entre les propriétés structurales et physiques de ces métallophosphonates ouvre la voie vers la conception de nouveaux matériaux multifonctionnels originaux. / This PhD work deals with the study of new lamellar magnetic and luminescent organic-inorganic hybrid materials synthesized by hydrothermal process. These materials were obtained from 3d transition metal salts (Cu2+, Co2+, Mn2+, Zn2+) and low symmetric organic molecules bearing at least one phosphonic acid function grafted onto a rigid aromatic platform (phenyl or naphthalene). The choice of the metal cation as well as additional functions (halogen: F, Cl, Br, I, carboxylic acid or methyl) on these cyclic systems led to two-dimensional hybrid materials with various architectures and physical properties (luminescence, magnetism and/or magnetoelectric coupling). Understanding the interconnections between the structural and physical properties of these metal phosphonates paves the way for the design of novel multifunctional materials.

Polymer brushes can be used to tailor the physical and chemical properties of materials on demand to meet potential applications. Therefore, fabrication of polymer brushes with well-defined structure and functional groups enables the engineering of new materials with diverse functions. In addition, two-dimensional (2D) materials have their unique physical/chemical properties and potential applications in (opt)electronics, catalysis, energy storage, sensing, and other related fields. However, the dispersibility, chemical stability, charge transport behavior, mechanical properties of the 2D materials hinder their further applications. Therefore, combining polymer brushes and 2D materials may bring in new properties which are not available by either of them alone. This thesis focuses on brushing up 2D materials (from inorganic to organic) with universal photografting techniques. (1) The first chapter introduces the outline and research content of the thesis. (2) The second chapter describes the background of 2D materials and polymer brushes. In particular, this chapter analyzes mechanisms, drawbacks and benefits of different polymerization methods, and also summarizes the general approaches to grow polymer brushes on 2D material surfaces, coupling with potential applications of polymer functionalized 2D materials. (3) The third chapter shows the motivation and aim of this thesis. (4) The fourth chapter discusses the results of the functionalization of hexagonal boron nitride (hBN), MoS2, graphitic-carbon nitride (gCN), alkyl-polydopamine (alkyl-PDA), and conjugated 2D polymers (2DPs) with polymer brushes by the same self-initiated photografting and photopolymerization (SIPGP) method and their related applications in detail, respectively. First, the direct photopolymerization of vinyl monomers results in the formation of thick and homogeneous polymer brushes covalently bounded to hBN. The brush layer mechanically and chemically stabilizes the material and allows facile handling as well as long-term use in water splitting hydrogen evolution reactions. Second, the chapter demonstrates the MoS2 can be directly modified with polymer brushes by SIPGP. After modifying MoS2 with polymer brushes, the dispersibility of polymer brushes-modified MoS2 was obviously improved. Third, the polymer brushes functionalized gCN significantly improves the dispersibility. Application of polymer brush functionalized gCN as excellent recyclable substrates for an outstanding SERS as well as photocatalytic degradation of dyes is demonstrated. Fourth, to directly obtain the 2D materials with functional groups, the chapter proposes a facile method to prepare amphiphilic polymeric Janus nanosheets with hydrophilic PDA and hydrophobic alkyl chains at both sides. Benefiting from the Janus property of the alkyl-PDA nanosheets, the nanosheets can be grafted polymer brushes through photografting and be conjugated Fe3O4 nanoparticles selectively onto the PDA side. Finally, the chapter shows that various polymer brushes can be directly grafted onto 2DPs and freestanding system is also obtained. Moreover, it is found that the morphology of freestanding system quickly and reversibly responds to solvent quality by shrinking/stretching. (5) The fifth chapter addresses the general conclusion and future prospective of the whole work. (6) The sixth chapter describes the experiment part of the whole thesis.

Keywords: Arabidopsis thaliana, phytoremediation, abiotic stress, ibuprofene, doxorubicin, two-dimensional electrophoresis Nowadays, develop of the pharmaceutical industry is very fast. Reason of this trend is ever-increasing number of diseases, lifestyle and still increasing demand for the drugs. With this trend growing interest in the analysis of the residues of pharmaceuticals in the environment which is result of incomplete wastewater treatment. This diploma thesis is studying effect of cytostatic drugs, specifically doxorubicin and one of the most widely used analgesics - ibuprofen, at the proteome level of the model plant Arabidopsis thaliana. Proteins isolated from plants exposed to the drugs were separated by two-dimensional electrophoresis. Comparing of protein maps by PDQest program (Bio-Rad, USA) was found several proteins whose expression was affected by the presence of drugs in the culture medium. Selected proteins were identified by LC - MS / MS.

Chemical substances are transferred between bumblebees of the species Bombus terrestris during their mating behavior. These substances are present mainly on the cuticle. The aim of this thesis was to identify and quantitatify differences in the amount of the compounds among defined groups of bumblebees - mated, non-mated and attempting to mate. Cuticular extracts were obtained by washing of the whole bumblebees bodies in hexane. These extracts were analyzed by using a two-dimensional gas chromatography with the time of fly mass spectrometr (GCxGC-TOF/MS). Cuticular hydrocarbons were identified and semi-quantified. Double bounds locations were determined in heptacosene and nonacosene. Five compounds were differed in the examined groups - β-springene, α-springene, dihydrofarnesyl-oleate, palmityl-palmitate and palmityl- palmitoleate. By comparing of the amount of these compounds differences between defined groups of bumblebees were determined. Analysis of the cutilar extracts showed that mated and non-mated bumblebees can be distinguished. Furthermore, there were statistically significant differences in the amounts of identified compounds in all defined groups of bumblebees. Key words: two-dimensional gas chromatography, Bombus terrestris, cutilar extract

Since the first successful isolation and subsequent characterization of graphene, the interest in two dimensional (2-D) materials has expanded exponentially. Despite the dozens of graphene-like van der Waals materials that have been found and their interesting properties, a significant obstacle in realizing their promise is their instability especially for monolayer and thin layers at elevated temperature. To overcome the obstacle of passivating the 2-D materials and study their properties at elevated temperature, we take advantage of the potential improvements afforded by assembling heterostructures by stacking the atomic thick 2-D materials together hexagonal boron nitride (ℎ-BN) which possess high chemical stability and thermal stability. In this dissertation, several experiments are described in detail in which we utilized h-BN encapsulation to passivate atomically-thin transition metal dichalcogenide and studied their properties at elevated temperature. In the first project we demonstrated that chemical vapor deposition (CVD)-grown flakes of high-quality monolayers of WS₂ can be stabilized at elevated temperatures by encapsulation with only top ℎ-BN layers in the presence of ambient air, N₂ or forming gas. The best passivation occurs for ℎ-BN covered samples with flowing N₂. In the second project, we demonstrated that encapsulating monolayer MoSe₂ and WS₂ with top and bottom ℎ-BN can improve their thermal stability at high temperature and increase their photoluminescence (PL). The increased PL likely occurs because impurities are laterally expelled from the TMD stack during heating. In the third project, we demonstrated the passivation of different modes of ℎ-BN encapsulation on thin layer FeSe sample by using temperature dependent Raman scattering. The complete encapsulation showed the best protection of thin layer FeSe. Finally, we utilized the temperature dependence of the Raman mode of thin-layer FeSe with complete encapsulation and applied a noncontact method to measure the thermal conductivity of the thin-layer FeSe.

<p>Technological advancements in electronics industry are driven by innovations in device fabrication techniques and development of novel materials. Halide perovskites are one of the latest additions to the semiconductor family. The performance of solid-state devices based on halide perovskites is now competing with other well-established semiconductors like silicon and gallium arsenide. However, the intrinsic instability of three-dimensional (3D) perovskites poses a great challenge in their widespread commercialization. The soft crystal lattice of hybrid halide perovskites facilitates anionic diffusion which impacts material stability, optoelectronic properties, and solid-state device performance.</p> <p>Two-dimensional (2D) halide perovskites with organic capping layers have been used for improving the extrinsic stability as well as suppressing intrinsic anionic diffusion. Nevertheless, a fundamental understanding of the role of compositional tuning, especially the impact of organic cations, in inhibiting anionic diffusion across the perovskite-ligand interface is missing. In our research, we first developed a library of atomically sharp and flat 2D heterostructures between two arbitrarily determined phase-pure halide perovskite single crystals. This platform was then used to perform a systematic investigation of anionic diffusion mechanism and quantify the impact of structural components on anionic inter-diffusion in halide perovskites. </p> <p>Stark differences were observed in anionic diffusion across 2D halide perovskite lateral and vertical heterostructures. Halide inter-diffusion in lateral heterostructures was found to be similar to the classical Fickian diffusion featuring continuous concentration profile evolution. However, vertical heterostructures show a “quantized” layer-by-layer diffusion behavior governed by a local free energy minimum and ion-blocking effects of the organic cations. For both lateral and vertical migrations, halide diffusion was found to be faster in perovskites with larger inorganic layer thickness. The increment becomes less apparent as the inorganic layer thickness increases, akin to the quantum confinement effect observed for band gaps. Furthermore, we found that bulkier and more rigid π-conjugated organic cations inhibit halide inter-diffusion much more effectively compared to short chain aliphatic cations. These results offer significant insights into the mechanism of anionic diffusion in 2D perovskites and provide a new materials platform for heterostructure assembly and device integration.</p>